Modified friction stir clinching of dissimilar AA2024-T3 to AA7075-T6: Effect of tool rotational speed and penetration depth

2019 ◽  
Vol 47 ◽  
pp. 157-171 ◽  
Author(s):  
Moslem Paidar ◽  
Sara Ghavamian ◽  
Olatunji Oladimeji Ojo ◽  
Ali Khorram ◽  
Amirhosein Shahbaz
Keyword(s):  
Penetration Depth ◽  
Rotational Speed ◽  
Tool Rotational Speed ◽  
Friction Stir

Comparison of response surface methodology with artificial neural network for prediction of the tensile properties of friction stir-processed surface composites

2021 ◽  
pp. 095440892110368
Author(s):  
Ravi Butola ◽  
Ranganath M. Singari ◽  
Qasim Murtaza ◽  
Lakshay Tyagi
Keyword(s):  
Neural Network ◽  
Artificial Neural Network ◽  
Tensile Strength ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Rotational Speed ◽  
Total Elongation ◽  
Tool Rotational Speed ◽  
Friction Stir ◽  
Artificial Neural

In the present work, nanoboron carbide is integrated in the aluminum matrix using friction stir processing: by varying process parameters, that is, tool pin profile, tool rotational speed and tool traverse speed, based on Taguchi L16 design of experiment. A self-assembled monolayer is successfully developed on the substrate to homogeneously and uniformly distribute the reinforcement particles. Response surface methodology and artificial neural network models are developed using ultimate tensile strength and total elongation as responses. Percentage absolute error between the experimental and predicted values of ultimate tensile strength and total elongation for the response surface methodology model is 3.537 and 2.865, respectively, and for artificial neural network is 2.788 and 2.578, respectively. For both the developed models experimental and forecasted values are in close approximation. The artificial neural network model showed slightly better predictive capacity compared to the response surface methodology model. From the scanning electron microscopy micrograph, it is evident that throughout the matrix B4C reinforcement particles are well distributed also; with increasing tool rotational speed grain size decreases up to 1200 r/min; on further increasing the tool rotational speed particles starts clustering.

Effect of Al2O3 nanoparticles on microstructure and mechanical properties of friction stir-welded dissimilar aluminum alloys AA7075-T6 and AA6061-T6

2021 ◽  
pp. 095440892110655
Author(s):  
Sumit Jain ◽  
R.S. Mishra
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Particle Dispersion ◽  
Al2o3 Nanoparticles ◽  
Tool Rotational Speed ◽  
Micro Hardness ◽  
Friction Stir ◽  
Dissimilar Aluminum Alloys

In this research, a defect-free dissimilar weld joint of AA7075-T6 and AA6061-T6 reinforced with Al2O3 nanoparticles was fabricated via friction stir welding (FSW). The influence of tool rotational speed (700, 900 and 1100 rpm), traverse speed (40, 50 and 60 mm/min) with varying volume fractions of Al2O3 nanoparticles (4%, 7% and 10%) on microstructural evolution and mechanical properties were investigated. The augmentation of various mechanical properties is based on the homogeneity of particle dispersion and grains refinement in the SZ of the FSWed joint. The findings revealed that the remarkable reduction in grain size in the SZ was observed owing to the incorporation of Al2O3 nanoparticles produces the pinning effect, which prevents the growth of grain boundaries by dynamic recrystallization (DRX). The increasing volume fraction of Al2O3 nanoparticles enhanced the mechanical properties such as tensile strength, % elongation and micro-hardness. Agglomeration of particles was observed in the SZ of the FSWed joints produced at lower tool rotational speed of 700 rpm and higher traverse speed of 60 mm/min due to unusual material flow. Homogenous particle dispersion and enhanced material mixing ensue at higher rotational speed of 1100 rpm and lower traverse speed of 40 mm/min exhibit higher tensile strength and micro-hardness.

scholarly journals Microstructure and Mechanical Properties of Friction Stir Welded Joints Between Commercially Pure Copper and Al 6351 Alloy

2017 ◽  
Vol 62 (3) ◽  
pp. 1819-1825
Author(s):  
V.C. Sinha ◽  
S. Kundu ◽  
S. Chatterjee
Keyword(s):  
Mechanical Properties ◽  
Welded Joints ◽  
Rotational Speed ◽  
Pure Copper ◽  
Stir Zone ◽  
Tool Rotational Speed ◽  
Friction Stir ◽  
Commercially Pure ◽  
Microstructure And Mechanical Properties ◽  
Commercially Pure Copper

AbstractIn the present study, the effect of tool rotational speed on microstructure and mechanical properties of friction stir welded joints between commercially pure copper and 6351 Al alloy was carried out in the range of tool rotational speeds of 300-900 rpm in steps of 150 rpm at 30 mm/minutes travel speed. Up to 450 rpm, the interface of the joints is free from intermetallics and Al4Cu9intermetallic has been observed at the stir zone. However, Al4Cu9intermetallic was observed both at the interface and the stir zone at 600 rpm. At 750 and 900 rpm tool rotational speed, the layers of AlCu, Al2Cu3and Al4Cu9intermetallics were observed at the interface and only Al4Cu9intermetallics has been observed in the stir zone. The maximum ultimate tensile strength of ~207 MPa and yield strength of ~168 MPa along with ~6.2% elongation at fracture of the joint have been obtained when processed at 450 rpm tool rotational speed.

Sign in / Sign up

Export Citation Format

Share Document