Mechanical properties of laser beam welded similar and dissimilar aluminum alloys

2017 ◽  
Vol 29 ◽  
pp. 272-280 ◽  
Author(s):  
J. Enz ◽  
M. Kumar ◽  
S. Riekehr ◽  
V. Ventzke ◽  
N. Huber ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloys ◽  
Laser Beam ◽  
Dissimilar Aluminum Alloys

scholarly journals Mechanical properties of 5052/2017 dissimilar aluminum alloys deposit by friction surfacing

2004 ◽  
Vol 54 (9) ◽  
pp. 373-379
Author(s):  
Hiroshi TOKISUE ◽  
Kazuyoshi KATOH ◽  
Toshikatsu ASAHINA ◽  
Toshio USHIYAMA
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloys ◽  
Friction Surfacing ◽  
Dissimilar Aluminum Alloys

Evaluation of dissimilar joints properties of 5083-H12 and 6061-T6 aluminum alloys produced by tungsten inert gas and friction stir welding

2015 ◽  
Vol 231 (3) ◽  
pp. 297-308 ◽  
Author(s):  
Morteza Ghaffarpour ◽  
Mohammad Kazemi ◽  
Mohammad Javad Mohammadi Sefat ◽  
Ahmad Aziz ◽  
Kamran Dehghani
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Aluminum Alloys ◽  
Traverse Speed ◽  
Inert Gas ◽  
Dissimilar Joints ◽  
Friction Stir ◽  
Dissimilar Aluminum Alloys ◽  
The Difference ◽  
Welding Processes

In the present study, friction stir welding (FSW) and tungsten inert gas (TIG) techniques were used to join the dissimilar aluminum alloys of 5083-H12 and 6061-T6. The laboratory tests were designed using design of experiment (DOE) method. Variables for the FSW process were the rotational speed, traverse speed, shoulder diameter, and pin diameter. They changed in ranges of 700–2500 r/min, 25–400 mm/min, 10–14 mm, and 2–4 mm, respectively. In the case of TIG process, the variables were current intensity, traverse speed, and tilt angle. These parameters varied from 80 to 90 A, 200 to 400 mm/min, and 3° to 12°, respectively. The optimum amounts of parameters were obtained using response surface methodology (RSM). The RSM-based model was developed to predict ultimate tensile strength (UTS) of the welds produced. In FSW, the difference between predicted and measured UTS was about 1.28% and in TIG it was 1.78%. The good agreement between experimental and predicted results indicates the high accuracy of the developed model. Mechanical properties and also the microstructure of the welds were compared after optimizing both welding processes using RSM. The results showed that the welds produced by FSW indicated a considerably higher quality and also improved mechanical properties compared to TIG. Properties of the joints obtained by FSW in single-sided joints were more desirable. In the double-sided welds obtained by FSW these differences were of an even higher significance.

Investigation of structural and mechanical properties of magnetic pulse welded dissimilar aluminum alloys

2019 ◽  
Vol 37 ◽  
pp. 292-304 ◽  
Author(s):  
Mehdi Pourabbas ◽  
Amir Abdollah-zadeh ◽  
Morteza Sarvari ◽  
Majid Pouranvari ◽  
Reza Miresmaeili
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloys ◽  
Magnetic Pulse ◽  
Dissimilar Aluminum Alloys

Metallurgical Studies on the Friction Stir Welding of Dissimilar A356 and A413 Alloys

2012 ◽  
Vol 488-489 ◽  
pp. 345-349
Author(s):  
G. Elatharasan ◽  
V.S. Senthil Kumar
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Aluminum Alloys ◽  
Structural Characteristics ◽  
Grain Structure ◽  
Cast Aluminum ◽  
Friction Stir ◽  
Dissimilar Aluminum Alloys ◽  
Cast Aluminum Alloys ◽  
Welding Defects

Friction stir welding is a technique useful for joining aluminum alloys that are difficult to weld. In recent years, however the focuses has been on welding dissimilar aluminum alloys, and analyze their mechanical properties and micro-structural characteristics. In the present study, the less investigated welding of cast aluminum alloys is considered. Cast aluminum alloys, A356 and A413, commonly used in automotive and aerospace industries, were friction-stir welded and their mechanical properties and micro-structural characteristics were analyzed. On testing their welded region, no welding defects were observed. The welded region exhibited a maximum tensile strength of 90 N/mm2 and Vickers micro-hardness of 56.8. The micro-structural observations at the nugget region revealed a refined grain structure.

Sign in / Sign up

Export Citation Format

Share Document