Effects of Ni addition and cyclic sintering on microstructure and mechanical properties of coarse grained WC–10Co cemented carbides

2016 ◽  
Vol 57 ◽  
pp. 64-69 ◽  
Author(s):  
Xiang Zhang ◽  
Jianhua Zhou ◽  
Nan Lin ◽  
Kun Li ◽  
Kun Fu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Coarse Grained ◽  
Cemented Carbides ◽  
Microstructure And Mechanical Properties ◽  
Ni Addition

scholarly journals Study on Microstructure and Mechanical Properties of WC-10Ni3Al Cemented Carbide Prepared by Different Ball-Milling Suspension

Materials ◽  
2019 ◽  
Vol 12 (14) ◽  
pp. 2224 ◽  
Author(s):  
Minai Zhang ◽  
Zhun Cheng ◽  
Jingmao Li ◽  
Shengguan Qu ◽  
Xiaoqiang Li
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Ball Milling ◽  
Grain Growth ◽  
Organic Solvents ◽  
Crack Deflection ◽  
Cemented Carbides ◽  
Powder Metallurgy Method ◽  
Microstructure And Mechanical Properties ◽  
Α Al2o3

In this paper, WC-10Ni3Al cemented carbides were prepared by the powder metallurgy method, and the effects of ball-milling powders with two different organic solvents on the microstructure and mechanical properties of cemented carbides were studied. We show that the oxygen in the organic solvent can be absorbed into the mixed powders by ball-milling when ethanol (CH3CH2OH) is used as a ball-milling suspension. This oxygen leads to the formation of α-Al2O3 during sintering, which improves the fracture toughness, due to crack deflection and bridging, while the formation of η-phase (Ni3W3C) inhibits the grain growth and increases the hardness. Alternatively, samples milled using cyclohexane (C6H12) showed grain growth during processing, which led to a decrease in hardness. Therefore, the increase of oxygen content from using organic solvents during milling improves the properties of WC-Ni3Al composites. The growth of WC grains can be inhibited and the hardness can be improved without loss of toughness by self-generating α-Al2O3 and η-phase (Ni3W3C).

Effect of carbon content on microstructure and mechanical properties of WC-10Co cemented carbides with plate-like WC grain

2020 ◽  
Vol 46 (2) ◽  
pp. 1824-1829 ◽  
Author(s):  
Qiumin Yang ◽  
Shusheng Yu ◽  
Chaoliang Zheng ◽  
Jiaxi Liao ◽  
Jinzhong Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Content ◽  
Cemented Carbides ◽  
Microstructure And Mechanical Properties

scholarly journals Effect of Cooling Rate on Microstructure and Mechanical Properties in the CGHAZ of Electroslag Welded Pearlitic Rail Steel

Metals ◽  
2019 ◽  
Vol 9 (7) ◽  
pp. 742 ◽  
Author(s):  
Khan ◽  
Yu ◽  
Wang ◽  
Jiang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Cooling Rate ◽  
Rail Steel ◽  
Interlamellar Spacing ◽  
Coarse Grained ◽  
Microstructure And Mechanical Properties ◽  
Confocal Scanning Laser ◽  
Start Temperature ◽  
Pearlitic Rail Steel

The effect of cooling rate, ranging from 6 to 1 °C/s, on microstructure and mechanical properties in the coarse-grained heat affected zone (CGHAZ) of electroslag welded pearlitic rail steel has been investigated by using confocal scanning laser microcopy (CSLM) and Gleeble 3500 thermo-mechanical simulator. During heating, the formed austenite was inhomogeneous with fractions of untransformed ferrite, which has influenced the pearlite transformation during cooling by providing additional nucleation sites to pearlite. During cooling, at 6 °C/s, the microstructure was composed of martensite and bainite with little pearlite. From 4 to 1 °C/s, microstructures were completely pearlite. Lowering the cooling rate of the CGHAZ from 4 to 1 °C/s increased the pearlite start temperature and reduced the pearlite growth rate. Meanwhile, this increase in pearlite start temperature enlarged the pearlite interlamellar spacing. Alternatively, increasing pearlite interlamellar spacing in the CGHAZ by lowering the cooling rate from 6 to 1 °C/s reduced the hardness and tensile strength, whereas toughness was found unaffected by the pearlite interlamellar spacing. It has been found that a cooling rate of 4 °C/s leads to the formation of pearlite with fine interlamellar spacing of 117 nm in the CGHAZ of electroslag welded pearlitic rail steel where hardness is 425 HV, tensile strength is 1077 MPa, and toughness is 9.1 J.

Effect of VC Addition on Microstructure and Mechanical Properties of Ultrafine Grained WC-Co Alloys

2014 ◽  
Vol 893 ◽  
pp. 444-448 ◽  
Author(s):  
Xue Mei Liu ◽  
Xiao Yan Song ◽  
Hai Bin Wang ◽  
Yang Gao ◽  
Yao Wang
Keyword(s):  
Mechanical Properties ◽  
Composite Powder ◽  
Cemented Carbides ◽  
Comprehensive Properties ◽  
Microstructure And Mechanical Properties ◽  
Plasma Sintering ◽  
Ultrafine Grained ◽  
Spark Plasma ◽  
Co Alloys

This study was focused on the effect of VC addition on the microstructure and mechanical properties of the prepared ultrafine grained cemented carbides. VC was added to the rawoxide materials which were synthesized to the WC-Co composite powder by the in-situ reduction and carbonization process. The ultrafine grained WC-Co alloys were fabricated by the spark plasma sintering technique using the prepared WC-Co composite powder. The phase constitution, microstructure characteristics and mechanical properties of the sintered ultrafine grained cemented carbides were analyzed quantitatively. The study proposed that VC plays a significant role in decreaseing the grain size of the prepared WC-Co alloy. The ultrafine grained WC-Co alloy with high comprehensive properties can be obtained as an appropriate addition of VC in the developed process.

Sign in / Sign up

Export Citation Format

Share Document