Impact of selected parameters on refrigerant flow boiling heat transfer and pressure drop in minichannels

2015 ◽  
Vol 56 ◽  
pp. 198-212 ◽  
Author(s):  
Magdalena Piasecka
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Flow Boiling Heat Transfer

Flow Boiling Heat Transfer, Pressure Drop, and Flow Pattern for CO2 in a 3.5mm Horizontal Smooth Tube

2009 ◽  
Vol 131 (9) ◽  
Author(s):  
Chang Yong Park ◽  
Pega Hrnjak
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Pattern ◽  
Mass Flux ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Flow Patterns ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Flow Boiling Heat Transfer

Abstract C O 2 flow boiling heat transfer coefficients and pressure drop in a 3.5mm horizontal smooth tube are presented. Also, flow patterns were visualized and studied at adiabatic conditions in a 3mm glass tube located immediately after a heat transfer section. Heat was applied by a secondary fluid through two brass half cylinders to the test section tubes. This research was performed at evaporation temperatures of −15°C and −30°C, mass fluxes of 200kg∕m2s and 400kg∕m2s, and heat flux from 5kW∕m2 to 15kW∕m2 for vapor qualities ranging from 0.1 to 0.8. The CO2 heat transfer coefficients indicated the nucleate boiling dominant heat transfer characteristics such as the strong dependence on heat fluxes at a mass flux of 200kg∕m2s. However, enhanced convective boiling contribution was observed at 400kg∕m2s. Surface conditions for two different tubes were investigated with a profilometer, atomic force microscope, and scanning electron microscope images, and their possible effects on heat transfer are discussed. Pressure drop, measured at adiabatic conditions, increased with the increase of mass flux and quality, and with the decrease of evaporation temperature. The measured heat transfer coefficients and pressure drop were compared with general correlations. Some of these correlations showed relatively good agreements with measured values. Visualized flow patterns were compared with two flow pattern maps and the comparison showed that the flow pattern maps need improvement in the transition regions from intermittent to annular flow.

Effect of Inlet Restriction on Flow Boiling Heat Transfer in a Horizontal Microtube

2013 ◽  
Vol 135 (2) ◽  
Author(s):  
YanFeng Fan ◽  
Ibrahim Hassan
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Drop ◽  
Critical Heat Flux ◽  
Mass Flux ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Mass Fluxes ◽  
Flow Boiling Heat Transfer ◽  
Low Mass

Flow boiling heat transfer in a horizontal microtube with inlet restriction (orifice) under uniform heating condition is experimentally investigated using FC-72 as working fluid. A stainless steel microtube with an inner diameter of 889 μm is selected as main microtube. Two microtubes with smaller diameters are assembled at the inlet of main microtube to achieve the restriction ratios of 50% and 20%. The experimental measurement is carried out at mass fluxes ranging from 160 to 870 kg/m2·s, heat fluxes varying from 6 to 170 kW/m2, inlet temperatures of 23 and 35 °C, and saturation pressures of 10 and 45 kPa. The effects of the orifices on two-phase pressure drop, critical heat flux (CHF), and flow boiling heat transfer coefficient are studied. The results show that the pressure drop caused by the orifice takes a considerable portion in the total pressure drop at low mass fluxes. This ratio decreases as the vapor quality or mass flux increases. The difference of normal critical heat flux in the microtubes with different orifice sizes is negligible. In the aspect of flow boiling heat transfer, the orifice is able to enhance the heat transfer at low mass flux and high saturation pressure, which indicates the contribution of orifice in the nucleate boiling dominated regime. However, the effect of orifice on flow boiling heat transfer is negligible in the forced convective boiling dominated regime.

Sign in / Sign up

Export Citation Format

Share Document