CO2 and R410A flow boiling heat transfer, pressure drop, and flow pattern at low temperatures in a horizontal smooth tube

2007 ◽  
Vol 30 (1) ◽  
pp. 166-178 ◽  
Author(s):  
C.Y. Park ◽  
P.S. Hrnjak
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Pattern ◽  
Low Temperatures ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Smooth Tube ◽  
Flow Boiling Heat Transfer ◽  
Transfer Pressure

Flow Boiling Heat Transfer, Pressure Drop, and Flow Pattern for CO2 in a 3.5mm Horizontal Smooth Tube

2009 ◽  
Vol 131 (9) ◽  
Author(s):  
Chang Yong Park ◽  
Pega Hrnjak
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Pattern ◽  
Mass Flux ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Flow Patterns ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Flow Boiling Heat Transfer

Abstract C O 2 flow boiling heat transfer coefficients and pressure drop in a 3.5mm horizontal smooth tube are presented. Also, flow patterns were visualized and studied at adiabatic conditions in a 3mm glass tube located immediately after a heat transfer section. Heat was applied by a secondary fluid through two brass half cylinders to the test section tubes. This research was performed at evaporation temperatures of −15°C and −30°C, mass fluxes of 200kg∕m2s and 400kg∕m2s, and heat flux from 5kW∕m2 to 15kW∕m2 for vapor qualities ranging from 0.1 to 0.8. The CO2 heat transfer coefficients indicated the nucleate boiling dominant heat transfer characteristics such as the strong dependence on heat fluxes at a mass flux of 200kg∕m2s. However, enhanced convective boiling contribution was observed at 400kg∕m2s. Surface conditions for two different tubes were investigated with a profilometer, atomic force microscope, and scanning electron microscope images, and their possible effects on heat transfer are discussed. Pressure drop, measured at adiabatic conditions, increased with the increase of mass flux and quality, and with the decrease of evaporation temperature. The measured heat transfer coefficients and pressure drop were compared with general correlations. Some of these correlations showed relatively good agreements with measured values. Visualized flow patterns were compared with two flow pattern maps and the comparison showed that the flow pattern maps need improvement in the transition regions from intermittent to annular flow.

The Characteristics of Flow Boiling Heat Transfer and Pressure Drop in Small Tube with the Pipe Sections Having Increased Diameters

2013 ◽  
Vol 651 ◽  
pp. 525-529
Author(s):  
Mao Yu Wen ◽  
Kang Jang Jang
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Small Diameter ◽  
Saturation Temperature ◽  
Smooth Tube ◽  
Flow Boiling Heat Transfer ◽  
Small Tube

This study presents an experimental investigation of the characteristics of the flow boiling heat transfer and pressure drop for refrigerant of R134a flowing in a small - diameter evaporative tube with the pipe sections having increased diameters. The experiments were performed at the saturation temperature of 5°C , heat flux of 5.12 ~ 10.96 ( KW/m2), mass flux of 200~600 ( kg/m2s), different length-to-diameter ratios of the test tubes and refrigerant quality of 0.07~0.78, and based on the same surface area of heat transfer. The enhancement performance ratios, θa/s for the tubes with the pipe sections having increased diameters relative to the smooth tube are higher than 1 (about 1.01~1.10). It means that the augmented tubes show the better overall performance than the smooth tube under study.

Augmented Performance of Flow Boiling Heat Transfer in a Tube With Axial Micro-Grooves and its Augmentation Mechanisms

1999 ◽  
Author(s):  
Lixin Cheng ◽  
Tingkuan Chen
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Axial Direction ◽  
Smooth Tube ◽  
Absolute Pressure ◽  
Transfer Coefficients ◽  
Frictional Pressure Drop ◽  
Flow Boiling Heat Transfer ◽  
Enhanced Tube

Abstract Experiments of upward flow boiling heat transfer with water in a vertical smooth tube and a tube with axial micro-grooves were respectively conducted. Both of the tested tubes have a length of 2.5 m, an inner diameter of 15 mm and an outlet diameter of 19 mm. The tube with axial micro grooves has many micro rectangle grooves in its inner wall along the axial direction. The grooves have a depth of 0.5 mm and a width of 0.3 mm. The tests were performed at an absolute pressure of 6 bar. The heat flux ranged from 0 to 550 kW/m2 and the mass flux was selected at 410, 610 and 810 kg/m2s, respectively. By comparison, flow boiling heat transfer coefficients in the enhanced tube are 1.6 ∼ 2.7 fold that in the smooth tube while the frictional pressure drop in the enhanced tube is slightly greater than that in the smooth tube. The augmentation of flow boiling heat transfer in the tube with axial micro-grooves is apparent. Based on the experimental data, a correlation of flow boiling heat transfer is proposed for the enhanced tube. Finally, the mechanisms of heat transfer enhancement are analyzed.

Sign in / Sign up

Export Citation Format

Share Document