Erratum to “A generalized correlation for refrigerant mass flow rate through adiabatic capillary tubes”[International Journal of Refrigeration 26 (2003) 881–888]

2004 ◽  
Vol 27 (4) ◽  
pp. 449
Author(s):  
Jongmin Choi ◽  
Yongchan Kim ◽  
Ho Young Kim
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Capillary Tubes ◽  
Generalized Correlation

Experimental Investigation on Flow Characteristic of Stepped Capillary Tube for Heat Pump Type Air Conditioner with R410A

2014 ◽  
Vol 960-961 ◽  
pp. 643-647
Author(s):  
Yan Sheng Xu
Keyword(s):  
Mass Flow Rate ◽  
Heat Pump ◽  
Mass Flow ◽  
Flow Rate ◽  
Capillary Tube ◽  
Coefficient Of Performance ◽  
Tube Length ◽  
Air Conditioner ◽  
Capillary Tubes ◽  
Tube Assembly

A stepped capillary tube consisting of two serially connected capillary tubes with different diameters is invented to replace the conventional expansion device. The mass flow rate of refrigerant R410A in stepped capillary tubes with different size were tested. The model of stepped capillary tube is proposed, and its numerical algorithm for tube length and mass flow rate is developed. The experimental results show that the performance comparing between stepped capillary tube system and capillary tube assembly system, the cooling capacity is reduced by 0.3%, the energy efficiency ratio (EER) is equal to each other, the heating capacity is increased by 0.3%, the coefficient of performance (COP) is decreased by 0.3%. That is to say, the performance index of the two kinds of throttle mechanism is almost identical. It indicates that the stepped capillary tube can replace the capillary tube assembly in the R410A heat pump type air conditioner absolutely. The model is validated with experimental data, and the results show that the model can be used for sizing and rating stepped capillary tube.

Effect of surface roughness on the mass flow rate predictions for adiabatic capillary tubes

2020 ◽  
Vol 118 ◽  
pp. 269-278 ◽  
Author(s):  
Thiago Torres Martins Rocha ◽  
Cleison Henrique de Paula ◽  
Vinícius Melo Cangussu ◽  
Antônio Augusto Torres Maia ◽  
Raphael Nunes de Oliveira
Keyword(s):  
Surface Roughness ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Capillary Tubes ◽  
Effect Of Surface

Assessment of Dimensionless Correlations for Prediction of Refrigerant Mass Flow Rate Through Capillary Tubes — A Review

2017 ◽  
Vol 25 (04) ◽  
pp. 1730004 ◽  
Author(s):  
Mehdi Rasti ◽  
Ji Hwan Jeong
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Capillary Tube ◽  
Capillary Tubes ◽  
Two Phase ◽  
Comprehensive Review ◽  
Wide Range ◽  
Inlet Conditions ◽  
Dimensionless Correlations

Capillary tubes are widely used as expansion devices in small-capacity refrigeration systems. Since the refrigerant flow through the capillary tubes is complex, many researchers presented empirical dimensionless correlations to predict the refrigerant mass flow rate. A comprehensive review of the dimensionless correlations for the prediction of refrigerants mass flow rate through straight and coiled capillary tubes depending on their geometry and adiabatic or diabatic capillary tubes depending on the flow configurations has been discussed. A comprehensive review shows that most of previous dimensionless correlations have problems such as discontinuity at the saturated lines or ability to predict the refrigerant mass flow rate only for the capillary tube subcooled inlet condition. The correlations suggested by Rasti et al. and Rasti and Jeong appeared to be general and continuous and these correlations can be used to predict the refrigerant mass flow rate through all the types of capillary tubes with wide range of capillary tube inlet conditions including subcooled liquid, two-phase mixture, and superheated vapor conditions.

General Equation for the Design of Capillary Tubes

1996 ◽  
Vol 118 (1) ◽  
pp. 150-154 ◽  
Author(s):  
Tuncay Yilmaz ◽  
Saban U¨nal
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
General Equation ◽  
Capillary Tube ◽  
Analytical Equation ◽  
Tube Length ◽  
Capillary Tubes

Capillary tubes are used widely in small refrigeration systems. It is necessary to design the capillary tube, but there does not exist any analytical equation which allows the determination of capillary tube length or mass flow rate for all refrigerants. In this work, an analytical equation is derived which allows to design the capillary tubes. The comparison with existing methods and experimentally obtained values using the refrigerants R12, R22, R113, R114, R134a, and R600a has turned out to be satisfactory.

Critical Mass Flow Rate Through Capillary Tubes

2010 ◽  
Author(s):  
A. Nouri-Borujerdi ◽  
P. Javidmand
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Numerical Study ◽  
Critical Mass ◽  
Small Diameter ◽  
Critical Conditions ◽  
Tube Length ◽  
Capillary Tubes ◽  
Drift Flux Model

This paper presented a numerical study that predicts critical mass flow rate, pressure, vapor quality, and void fraction along a very long tube with small diameter or capillary tub under critical condition by the drift flux model. Capillary tubes are simple expansion devices and are necessary to design and optimization of refrigeration systems. Using dimensional analysis by Buckingham’s π theory, some generalized correlations are proposed for prediction of flow parameters as functions of flow properties and tube sizes under various critical conditions. This study is performed under the inlet pressure in the range of 0.8 ≤ pin ≤ 1.5Mpa, subcooling temperature between 0 ≤ ΔTsub ≤ 10 °C. The tube diameter is in the range of 0.5 ≤ D ≤ 1.5mm and tube length between 1 ≤ L ≤ 2m for water, ammonia, refrigerants R-12, R-22 and R-134 as working fluids. Comparison between the results of the present work and some experimental data indicates a good agreement. Cluster of data close to the fitted curves also shows satisfactory results.

Sign in / Sign up

Export Citation Format

Share Document