In-plane and out-of-plane structural performance of fully grouted reinforced masonry walls with varying reinforcement ratio – A numerical study

2021 ◽  
Vol 248 ◽  
pp. 113288
Author(s):  
Sarkar Noor-E-Khuda ◽  
David P Thambiratnam
Keyword(s):  
Numerical Study ◽  
Reinforcement Ratio ◽  
Structural Performance ◽  
Masonry Walls ◽  
Reinforced Masonry ◽  
Out Of Plane

scholarly journals Experimental and Numerical Study of Behaviour of Reinforced Masonry Walls with NSM CFRP Strips Subjected to Combined Loads

Buildings ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 103
Author(s):  
Houria Hernoune ◽  
Benchaa Benabed ◽  
Antonios Kanellopoulos ◽  
Alaa Hussein Al-Zuhairi ◽  
Abdelhamid Guettala
Keyword(s):  
Failure Modes ◽  
Numerical Study ◽  
Masonry Wall ◽  
Brick Masonry ◽  
Masonry Walls ◽  
Near Surface ◽  
Combined Loads ◽  
Reinforced Masonry ◽  
Brick And Mortar ◽  
Near Surface Mounted

Near surface mounted (NSM) carbon fibers reinforced polymer (CFRP) reinforcement is one of the techniques for reinforcing masonry structures and is considered to provide significant advantages. This paper is composed of two parts. The first part presents the experimental study of brick masonry walls reinforced with NSM CFRP strips under combined shear-compression loads. Masonry walls have been tested under vertical compression, with different bed joint orientations 90° and 45° relative to the loading direction. Different reinforcement orientations were used including vertical, horizontal, and a combination of both sides of the wall. The second part of this paper comprises a numerical analysis of unreinforced brick masonry (URM) walls using the detailed micro-modelling approach (DMM) by means of ABAQUS software. In this analysis, the non-linearity behavior of brick and mortar was simulated using the concrete damaged plasticity (CDP) constitutive laws. The results proved that the application of the NSM-CFRP strips on the masonry wall influences significantly strength, ductility, and post-peak behavior, as well as changing the failure modes. The adopted DMM model provides a good interface to predict the post peak behavior and failure mode of unreinforced brick masonry walls.

On the out-of-plane flexural design of reinforced masonry walls

2020 ◽  
Vol 27 ◽  
pp. 100945 ◽  
Author(s):  
Sarkar Noor-E-Khuda ◽  
Manicka Dhanasekar
Keyword(s):  
Masonry Walls ◽  
Reinforced Masonry ◽  
Out Of Plane

scholarly journals Out-of-plane instability of reinforced masonry uniaxial specimens under reversed cyclic axial loading

2017 ◽  
Vol 44 (5) ◽  
pp. 367-376 ◽  
Author(s):  
Nazli Azimikor ◽  
Svetlana Brzev ◽  
Kenneth J. Elwood ◽  
Donald L. Anderson ◽  
William McEwen
Keyword(s):  
Axial Loading ◽  
Shear Walls ◽  
Reinforcement Ratio ◽  
Design Parameters ◽  
Key Factors ◽  
Cyclic Tension ◽  
Reinforced Masonry ◽  
Out Of Plane ◽  
Tension And Compression ◽  
Reversed Cyclic

Results of a study performed on the out-of-plane instability of reinforced masonry shear walls (RMSW) under seismic loading are presented. The study was conducted to gain understanding of the out-of-plane instability mechanism and the key factors influencing its development through the testing of five reinforced masonry uniaxial specimens under reversed cyclic tension and compression. The specimens represented the end zone of a RMSW. The design parameters considered in the study included longitudinal reinforcement ratio and height-to-thickness ratio for the test specimens. It was found that onset of out-of-plane instability is strongly influenced by the level of tensile strains developed in the specimens, the reinforcement ratio, and the bar size. In this case, out-of-plane instability occurred when out-of-plane displacements exceeded the critical value equal to half the wall thickness. A study on full-scale RMSW specimens subjected to reversed cyclic loading, also undertaken under this research program, is expected to verify the findings of this study and contribute towards development of design criteria for out-of-plane stability of RMSW.

Cyclic out-of-plane behaviour of tall reinforced masonry walls under P–Δ effects

2011 ◽  
Vol 33 (2) ◽  
pp. 287-297 ◽  
Author(s):  
Francesca da Porto ◽  
Flavio Mosele ◽  
Claudio Modena
Keyword(s):  
Masonry Walls ◽  
Reinforced Masonry ◽  
Out Of Plane

scholarly journals DEVELOPING A TEST SYSTEM FOR EVALUATING STRUCTURAL PERFORMANCE OF MASONRY WALLS UNDER OUT-OF-PLANE UNIFORM LOADS

2013 ◽  
Vol 19 (42) ◽  
pp. 591-594 ◽  
Author(s):  
Yulia HAYATI ◽  
Yasushi SANADA ◽  
So KASAHARA ◽  
Takuya TOMONAGA
Keyword(s):  
Test System ◽  
Structural Performance ◽  
Masonry Walls ◽  
Out Of Plane

Analysis of safety of slender concrete masonry walls in relation to CSA S304-14

2019 ◽  
Vol 46 (5) ◽  
pp. 424-438
Author(s):  
Andrea C. Isfeld ◽  
Anna Louisa Müller ◽  
Mark Hagel ◽  
Nigel G. Shrive
Keyword(s):  
Concrete Block ◽  
Masonry Wall ◽  
Masonry Walls ◽  
Effective Height ◽  
Design Standard ◽  
Euler Buckling ◽  
Concrete Masonry ◽  
Reinforced Masonry ◽  
Out Of Plane ◽  
Support Conditions

The Canadian masonry design standard appears to be overly conservative in determining the capacity of concrete block walls with slenderness ratios greater than 30. When assessing the potential for buckling of a masonry wall according to Euler buckling criteria, the effective height is determined in part from the end supports. In Euler theory only pinned, fixed and free support conditions are considered, and the Canadian standard considers the support conditions to be hinged, elastic or stiff. For a partially reinforced masonry wall a true hinged base support is expected to be difficult to achieve, as the width of the concrete block restrains rotation. The effect of the base support conditions on the deflected shape of partially grouted block walls was investigated under axial and out-of-plane loading. The results of this testing were compared with calculations based on the Canadian masonry standard. It becomes clear that the standard is overly conservative in many cases and the design of slender walls needs to be re-examined.

Sign in / Sign up

Export Citation Format

Share Document