Flexural response and load capacity of reinforced concrete beams strengthened with reinforced mortar layer

2021 ◽  
Vol 245 ◽  
pp. 112884
Author(s):  
Y.M. Alharthi ◽  
M. Emara ◽  
A.S. Elamary ◽  
I.A. Sharaky
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Load Capacity ◽  
Reinforced Concrete Beams ◽  
Flexural Response

scholarly journals Finite element analysis of reinforced concrete deep beam with large opening

2021 ◽  
Vol 10 (1) ◽  
Author(s):  
Elsayed Ismail ◽  
Mohamed S. Issa ◽  
Khaled Elbadry
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Load Capacity ◽  
Reinforced Concrete Beams ◽  
The Other ◽  
Deep Beam ◽  
Web Openings ◽  
Design Load ◽  
Large Opening

Abstract Background A series of nonlinear finite element (FE) analyses was performed to evaluate the different design approaches available in the literature for design of reinforced concrete deep beam with large opening. Three finite element models were developed and analyzed using the computer software ATENA. The three FE models of the deep beams were made for details based on three different design approaches: (Kong, F.K. and Sharp, G.R., Magazine of Concrete Res_30:89-95, 1978), (Mansur, M. A., Design of reinforced concrete beams with web openings, 2006), and Strut and Tie method (STM) as per ACI 318-14 (ACI318 Committee, Building Code Requirements for Structural Concrete (ACI318-14), 2014). Results from the FE analyses were compared with the three approaches to evaluate the effect of different reinforcement details on the structural behavior of transfer deep beam with large opening. Results The service load deflection is the same for the three models. The stiffnesses of the designs of (Mansur, M. A., Design of reinforced concrete beams with web openings, 2006) and STM reduce at a load higher than the ultimate design load while the (Kong, F.K. and Sharp, G.R., Magazine of Concrete Res_30:89-95, 1978) reduces stiffness at a load close to the ultimate design load. The deep beam designed according to (Mansur, M. A., Design of reinforced concrete beams with web openings, 2006) model starts cracking at load higher than the beam designed according to (Kong, F.K. and Sharp, G.R., Magazine of Concrete Res_30:89-95, 1978) method. The deep beam detailed according to (Kong, F.K. and Sharp, G.R., Magazine of Concrete Res_30:89-95, 1978) and (Mansur, M. A., Design of reinforced concrete beams with web openings, 2006) failed due to extensive shear cracks. The specimen detailed according to STM restores its capacity after initial failure. The three models satisfy the deflection limit. Conclusion It is found that the three design approaches give sufficient ultimate load capacity. The amount of reinforcement given by both (Mansur, M. A., Design of reinforced concrete beams with web openings, 2006) and (Kong, F.K. and Sharp, G.R., Magazine of Concrete Res_30:89-95, 1978) is the same. The reinforcement used by the STM method is higher than the other two methods. Additional reinforcement is needed to limit the crack widths. (Mansur, M. A., Design of reinforced concrete beams with web openings, (2006)) method gives lesser steel reinforcement requirement and higher failure load compared to the other two methods.

Performance of Reinforced Concrete Beams with Multiple Openings

2020 ◽  
Vol 857 ◽  
pp. 162-168
Author(s):  
Haidar Abdul Wahid Khalaf ◽  
Amer Farouk Izzet
Keyword(s):  
Reinforced Concrete ◽  
Ultimate Load ◽  
Concrete Beams ◽  
Load Capacity ◽  
Reinforced Concrete Beams ◽  
Design Parameters ◽  
Ultimate Load Capacity ◽  
Concentrated Load ◽  
Simply Supported ◽  
Group I

The present investigation focuses on the response of simply supported reinforced concrete rectangular-section beams with multiple openings of different sizes, numbers, and geometrical configurations. The advantages of the reinforcement concrete beams with multiple opening are mainly, practical benefit including decreasing the floor heights due to passage of the utilities through the beam rather than the passage beneath it, and constructional benefit that includes the reduction of the self-weight of structure resulting due to the reduction of the dead load that achieves economic design. To optimize beam self-weight with its ultimate resistance capacity, ten reinforced concrete beams having a length, width, and depth of 2700, 100, and 400 mm, respectively were fabricated and tested as simply supported beams under one incremental concentrated load at mid-span until failure. The design parameters were the configuration and size of openings. Three main groups categorized experimental beams comprise the same area of openings and steel reinforcement details but differ in configurations. Three different shapes of openings were considered, mainly, rectangular, parallelogram, and circular. The experimental results indicate that, the beams with circular openings more efficient than the other configurations in ultimate load capacity and beams stiffness whereas, the beams with parallelogram openings were better than the beams with rectangular openings. Commonly, it was observed that the reduction in ultimate load capacity, for beams of group I, II, and III compared to the reference solid beam ranged between (75 to 93%), (65 to 93%), and (70 to 79%) respectively.

Application of a Reinforced Self-Compacting Concrete Jacket in Damaged Reinforced Concrete Beams under Monotonic and Repeated Loading

2013 ◽  
Vol 2013 ◽  
pp. 1-12 ◽  
Author(s):  
Constantin E. Chalioris ◽  
Constantin P. Papadopoulos ◽  
Constantin N. Pourzitidis ◽  
Dimitrios Fotis ◽  
Kosmas K. Sideris
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Small Diameter ◽  
Structural Response ◽  
Reinforced Concrete Beams ◽  
Repeated Loading ◽  
Test Results ◽  
Self Compacting Concrete ◽  
Loading Test ◽  
Flexural Response

This paper presents the findings of an experimental study on the application of a reinforced self-compacting concrete jacketing technique in damaged reinforced concrete beams. Test results of 12 specimens subjected to monotonic loading up to failure or under repeated loading steps prior to total failure are included. First, 6 beams were designed to be shear dominated, constructed by commonly used concrete, were initially tested, damaged, and failed in a brittle manner. Afterwards, the shear-damaged beams were retrofitted using a self-compacting concrete U-formed jacket that consisted of small diameter steel bars and U-formed stirrups in order to increase their shear resistance and potentially to alter their initially observed shear response to a more ductile one. The jacketed beams were retested under the same loading. Test results indicated that the application of reinforced self-compacting concrete jacketing in damaged reinforced concrete beams is a promising rehabilitation technique. All the jacketed beams showed enhanced overall structural response and 35% to 50% increased load bearing capacities. The ultimate shear load of the jacketed beams varied from 39.7 to 42.0 kN, whereas the capacity of the original beams was approximately 30% lower. Further, all the retrofitted specimens exhibited typical flexural response with high values of deflection ductility.

scholarly journals Strengthening of Reinforced Concrete Members using Post-Tension Cables: A Parametric Research

2019 ◽  
Vol 8 (2S3) ◽  
pp. 1334-1338
Keyword(s):  
Reinforced Concrete ◽  
Parametric Study ◽  
Concrete Beams ◽  
Load Capacity ◽  
Reinforced Concrete Beams ◽  
Design Parameters ◽  
Internal Stresses ◽  
Force Magnitude ◽  
Post Tensioning ◽  
Post Tension

In building construction, post-tensioning allows longer clear spans, thinner slabs than the reinforced concrete beams. This paper presents a theoretical investigation on the behavior of existing reinforced concrete beams strengthened with post-tensioning cable(s) for increasing their load capacity. The proposed post-tensioning technique consists of stressing cable passing through a structural beam element starting from the top/bottom side and traversing the beam to the bottom/top side and then return back to the original side. A theoretical parametric study is conducted to study the effect of post-tensioning parameters on the internal stresses to optimize the design parameters. An excel spread sheet program was developed to calculate the internal straining actions at critical sections of the beam. A parametric study including the cable length, inclination angle of the cable and pre-stressing force magnitude was performed by using this program. This parametric study, led to well-defined guidelines for the proper use of the strengthening of beams by pre-stressing cables with adequate geometrical conditions of the cables

scholarly journals Post-strengthening of reinforced concrete beams with prestressed CFRP strips. Part 1: analysis under static loading

2012 ◽  
Vol 5 (3) ◽  
pp. 343-361
Author(s):  
M. R. Garcez ◽  
G. L. C. P. Silva Filho ◽  
Urs Meier
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Load Capacity ◽  
Experimental Studies ◽  
Reinforced Concrete Beams ◽  
Experimental Program ◽  
Existing Structures ◽  
Flexural Tests ◽  
Strengthening Technique ◽  
Epoxy Matrices

Different FPR post-strengthening techniques have been developed and applied in existing structures aiming to increase their load capacity. Most of the FRP systems used nowadays consist of carbon fibers embedded in epoxy matrices (CFRP). Regardless of the advantages and the good results shown by the CFRP post-strengthen technique, experimental studies show that, in most cases, the failure of post-strengthened structures is premature. Aiming to better use the tensile strength of the carbon fiber strips used as post-strengthening material, the application of prestressed CFRP strips started to be investigated. The main purpose of this paper is to analyze the effects of the composite prestressing in the performance of the CFRP post strengthening technique. The experimental program was based on flexural tests on post-strengthened reinforced concrete beams subjected to static - part 1 and cyclic - part 2 loading. Experimental results allowed the analysis of the quality and shortcomings of post-strengthen system studied, which resulted in valuable considerations about the analyzed post-strengthened beams.

The Behavior of Reinforced and Pre-Stressed Concrete Beams under Elevated Temperature

2020 ◽  
Vol 47 ◽  
pp. 15-30
Author(s):  
Amr H. Badawy ◽  
Ahmed Hassan ◽  
Hala El-Kady ◽  
L.M. Abd-El Hafez
Keyword(s):  
Reinforced Concrete ◽  
Elevated Temperature ◽  
Prestressed Concrete ◽  
Mechanical Performance ◽  
Concrete Beams ◽  
Load Capacity ◽  
Reinforced Concrete Beams ◽  
Flexural Behavior ◽  
Second Phase ◽  
Prestressed Beam

The behavior of unbounded post tension and reinforced concrete beams under elevated temperature was presented. The experimental work was consisted of two major phases. In the first phase, the objective was studying the mechanical performance of prestressed beam, prestressed beam with steel addition and reinforced concrete beams respectively were studied. In the second phase, the residual mechanical performance of prestressed beam, prestressed beam with steel addition and reinforced concrete beams under elevated 400oC, for 120 minutes durations. The failure mechanisms, ultimate load capacity, and deflection at critical sections were monitored. The numerical prediction of the flexural behavior of the tested specimens is presented in this paper. This includes a comparison between the numerical and experimental test results according to ANSYS models. The results indicate that the prestressed beam with steel addition and reinforced concrete beams had higher resistance to beams under elevated 400oC than that of prestressed concrete beam in terms of ultimate capacity. It is also shown that the reinforced concrete beams have higher resistance to beams under elevated temperature than that of prestressed beam, prestressed beam with steel addition.

Sign in / Sign up

Export Citation Format

Share Document