Negative bending behavior of novel U-shaped steel and concrete composite beams

2021 ◽  
Vol 237 ◽  
pp. 112217
Author(s):  
Yi Zhao ◽  
Xuhong Zhou ◽  
Yuanlong Yang ◽  
Jiepeng Liu ◽  
Yohchia Frank Chen
Keyword(s):  
Composite Beams ◽  
Bending Behavior ◽  
Negative Bending

scholarly journals Experimental investigation on composite beams under combined negative bending and torsional moments

2020 ◽  
pp. 136943322098166
Author(s):  
Weiwei Lin
Keyword(s):  
Ultimate Load ◽  
Mechanical Performance ◽  
Composite Beams ◽  
Strain Development ◽  
Shear Connectors ◽  
Load Carrying ◽  
Interface Slip ◽  
Negative Bending ◽  
Support Conditions ◽  
Main Girder

In this study, straight composite steel-concrete beams were tested to investigate their mechanical performance under combined negative bending and torsional moments. Two specimens were used in this study, and different ratios between the applied negative bending and torsional moments were induced. Load and deflection relationships, strain development on the steel main girder and shear connectors (stud), and the slip development on the steel-concrete interface were recorded in the test and reported in this paper. The results indicate that increase of torsional moment will result in the significant decrease of the load-carrying capacities (e.g. yield load and ultimate load) of the specimens. It was also found that the normal strains of stud shear connectors in such beams are very large and non-negligible compared to their shear strains. In addition, the maximum interface slip was found occurring at around the 1/4 span, and the support conditions and serious crack of the concrete were considered to be the main causes. The research results obtained in this study can provide references for the design and analysis of steel-concrete composite beams subjected to the combined negative bending and torsional moments.

scholarly journals Lateral distortional buckling of cellular composite-beams

2018 ◽  
Vol 11 (2) ◽  
pp. 331-356 ◽  
Author(s):  
A. D. PIASSI ◽  
J. V. DIAS ◽  
A. F. G. CALENZANI ◽  
F. C. C. MENANDRO
Keyword(s):  
Flexural Rigidity ◽  
Lateral Displacement ◽  
Limit State ◽  
Composite Beams ◽  
Bottom Flange ◽  
Distortional Buckling ◽  
Critical Moment ◽  
Negative Moment ◽  
Resistant Moment ◽  
Negative Bending

Abstract In the region of negative bending moments of continuous and semi-continuous steel and concrete composite beams, the inferior portion of the steel section is subjected to compression while the top flange is restricted by the slab, which may cause a global instability limit state know as lateral distortional buckling (LDB) characterized by a lateral displacement and rotation of the bottom flange with a distortion of the section’s web when it doesn’t have enough flexural rigidity. The ABNT NBR 8800:2008 provides an approximate procedure for the verification of this limit state, in which the resistant moment to LDB is obtained from the elastic critical moment in the negative moment region. One of the essential parameters for the evaluation of the critical moment is the composite beam’s rotational rigidity. This procedure is restricted only to to steel and concrete composite beams with sections that have plane webs. In this paper, an equation for the calculation of the rotational rigidity of cellular sections was developed in order to determine the LDB elastic critical moment. The formulation was verified by numerical analyses performed in ANSYS and its efficiency was confirmed. Finally, the procedure described in ABNT NBR 8800:2008 for the calculation of the critical LDB moment was expanded to composite beams with cellular sections in a numerical example with the appropriate modifications in geometric properties and rotational rigidity.

Study on the Crack in Concrete Flange of Outer-Plated Steel-Concrete Continuous Composite Beams

2012 ◽  
Vol 166-169 ◽  
pp. 1023-1028 ◽  
Author(s):  
Li Hua Chen ◽  
Qi Liang Jin ◽  
Haiyu Si
Keyword(s):  
Crack Width ◽  
Static Load ◽  
Bending Moment ◽  
Structural Features ◽  
Composite Beams ◽  
Test Results ◽  
Load Tests ◽  
Reversed Loading ◽  
Negative Bending ◽  
Stress Block

Static load tests were conducted on two reversed-loading simply supported and two continuous outer-plated steel-concrete composite beams to study the formation and development of cracks in such beams under negative bending moment. The test results show that based on the plane section assumption, it is an effective and economical method to calculate the cracking moment of the composite beams assuming a rectangular stress block for concrete in tension zone. Considering the structural features of outer-plated steel-concrete composite beams, the formula for calculating crack width of concrete flange of outer-plated steel-concrete composite beams is discussed and presented, and the calculated values of crack width agree well with the experimental results.

Behaviour and design of composite beams subjected to negative bending and compression

2012 ◽  
Vol 79 ◽  
pp. 34-47 ◽  
Author(s):  
G. Vasdravellis ◽  
B. Uy ◽  
E.L. Tan ◽  
B. Kirkland
Keyword(s):  
Composite Beams ◽  
Negative Bending

Research on Key Issues in Design of Outer-Plated Steel-Concrete Continuous Composite Beams

2012 ◽  
Vol 166-169 ◽  
pp. 414-419
Author(s):  
Li Hua Chen ◽  
Fei Xiao ◽  
Qi Liang Jin
Keyword(s):  
Composite Beam ◽  
Bending Moment ◽  
Longitudinal Shear ◽  
Structural Features ◽  
Composite Beams ◽  
Steel Beam ◽  
Negative Moment ◽  
Key Issues ◽  
Negative Bending ◽  
The Moment

Based on the theoretical analysis and testing results, some key issues in design of outer-plated steel-concrete continuous composite beams are discussed. The influence of the form of steel beam upper flange on the behavior of composite beam is analyzed. The requirements about longitudinal reinforcement strength in the concrete flange of the negative moment region are given. It is suggested that the moment-shear interaction should be neglected when calculating the flexural capacity of outer-plated steel-concrete composite beams under negative bending moment. The behavior of longitudinal shear resistance at the interface between the concrete flange and web of composite beam is studied, and the related calculating formula is put forward based on the structural features of the composite beam.

Sign in / Sign up

Export Citation Format

Share Document