Load-carrying capacity of timber joints with multiple glued-in steel rods loaded parallel to grain

2020 ◽  
Vol 225 ◽  
pp. 111302
Author(s):  
Bo-Han Xu ◽  
Dong-Feng Li ◽  
Yan-Hua Zhao ◽  
Abdelhamid Bouchaïr
Keyword(s):  
Carrying Capacity ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
Timber Joints

Load-carrying capacity of steel-to-timber joints with a pretensioned bolt

2008 ◽  
Vol 54 (5) ◽  
pp. 362-368 ◽  
Author(s):  
Ali Awaludin ◽  
Takuro Hirai ◽  
Toshiro Hayashikawa ◽  
Yoshihisa Sasaki
Keyword(s):  
Carrying Capacity ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
Timber Joints

Prediction of the load carrying capacity of bolted timber joints

1999 ◽  
Vol 33 (1) ◽  
pp. 15-29 ◽  
Author(s):  
L. Daudeville ◽  
L. Davenne ◽  
M. Yasumura
Keyword(s):  
Carrying Capacity ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
Timber Joints

Influence of Yield Strength Variability over Cross-Section to Steel Beam Load-Carrying Capacity

2005 ◽  
Vol 10 (2) ◽  
pp. 151-160 ◽  
Author(s):  
J. Kala ◽  
Z. Kala
Keyword(s):  
Yield Strength ◽  
Cross Section ◽  
Carrying Capacity ◽  
Bending Moment ◽  
Statistical Characteristics ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
Strength Variability ◽  
Hot Rolled ◽  
Hot Rolled Steel

Authors of article analysed influence of variability of yield strength over cross-section of hot rolled steel member to its load-carrying capacity. In calculation models, the yield strength is usually taken as constant. But yield strength of a steel hot-rolled beam is generally a random quantity. Not only the whole beam but also its parts have slightly different material characteristics. According to the results of more accurate measurements, the statistical characteristics of the material taken from various cross-section points (e.g. from a web and a flange) are, however, more or less different. This variation is described by one dimensional random field. The load-carrying capacity of the beam IPE300 under bending moment at its ends with the lateral buckling influence included is analysed, nondimensional slenderness according to EC3 is λ¯ = 0.6. For this relatively low slender beam the influence of the yield strength on the load-carrying capacity is large. Also the influence of all the other imperfections as accurately as possible, the load-carrying capacity was determined by geometrically and materially nonlinear solution of very accurate FEM model by the ANSYS programme.

Fuzzy Sets Theory in Comparison with Stochastic Methods to Analyse Nonlinear Behaviour of a Steel Member under Compression

2005 ◽  
Vol 10 (1) ◽  
pp. 65-75 ◽  
Author(s):  
Z. Kala
Keyword(s):  
Fuzzy Sets ◽  
Carrying Capacity ◽  
Stochastic Methods ◽  
Nonlinear Behaviour ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
Input Parameters ◽  
Stochastic Solution ◽  
Fuzzy Solution ◽  
Sets Theory

The load-carrying capacity of the member with imperfections under axial compression is analysed in the present paper. The study is divided into two parts: (i) in the first one, the input parameters are considered to be random numbers (with distribution of probability functions obtained from experimental results and/or tolerance standard), while (ii) in the other one, the input parameters are considered to be fuzzy numbers (with membership functions). The load-carrying capacity was calculated by geometrical nonlinear solution of a beam by means of the finite element method. In the case (ii), the membership function was determined by applying the fuzzy sets, whereas in the case (i), the distribution probability function of load-carrying capacity was determined. For (i) stochastic solution, the numerical simulation Monte Carlo method was applied, whereas for (ii) fuzzy solution, the method of the so-called α cuts was applied. The design load-carrying capacity was determined according to the EC3 and EN1990 standards. The results of the fuzzy, stochastic and deterministic analyses are compared in the concluding part of the paper.

Pavement Damage Due to Conventional and New Generation of Wide-Base Super Single Tires

2005 ◽  
Vol 33 (4) ◽  
pp. 210-226 ◽  
Author(s):  
I. L. Al-Qadi ◽  
M. A. Elseifi ◽  
P. J. Yoo ◽  
I. Janajreh
Keyword(s):  
Carrying Capacity ◽  
Material Properties ◽  
Three Dimensional ◽  
Fe Analysis ◽  
Load Carrying Capacity ◽  
Inflation Pressure ◽  
3D Finite Element ◽  
Load Carrying ◽  
Pavement Damage ◽  
New Generation

Abstract The objective of this study was to quantify pavement damage due to a conventional (385/65R22.5) and a new generation of wide-base (445/50R22.5) tires using three-dimensional (3D) finite element (FE) analysis. The investigated new generation of wide-base tires has wider treads and greater load-carrying capacity than the conventional wide-base tire. In addition, the contact patch is less sensitive to loading and is especially designed to operate at 690kPa inflation pressure at 121km/hr speed for full load of 151kN tandem axle. The developed FE models simulated the tread sizes and applicable contact pressure for each tread and utilized laboratory-measured pavement material properties. In addition, the models were calibrated and properly validated using field-measured stresses and strains. Comparison was established between the two wide-base tire types and the dual-tire assembly. Results indicated that the 445/50R22.5 wide-base tire would cause more fatigue damage, approximately the same rutting damage and less surface-initiated top-down cracking than the conventional dual-tire assembly. On the other hand, the conventional 385/65R22.5 wide-base tire, which was introduced more than two decades ago, caused the most damage.

Load carrying capacity of cylindrical shells

2020 ◽  
Vol 2020 (21) ◽  
pp. 146-153
Author(s):  
Anatolii Dekhtyar ◽  
◽  
Oleksandr Babkov ◽  
Keyword(s):  
Carrying Capacity ◽  
Cylindrical Shells ◽  
Load Carrying Capacity ◽  
Load Carrying
Sign in / Sign up

Export Citation Format

Share Document