Cross-section behavior of cold-formed steel elliptical hollow sections – A numerical study

2019 ◽  
Vol 201 ◽  
pp. 109797 ◽  
Author(s):  
Ye Yao ◽  
Wai-Meng Quach ◽  
Ben Young
Keyword(s):  
Cross Section ◽  
Numerical Study ◽  
Cold Formed Steel

Boundary element method in numerical study of three-dimensional Stokes flows in channels of arbitrary shape

2012 ◽  
Vol 9 (1) ◽  
pp. 94-97
Author(s):  
Yu.A. Itkulova
Keyword(s):  
Boundary Element Method ◽  
Boundary Element ◽  
Cross Section ◽  
Numerical Study ◽  
Three Dimensional ◽  
Cylindrical Tube ◽  
Variable Cross Section ◽  
Variable Cross ◽  
Periodic Flows ◽  
Element Method

In the present work creeping three-dimensional flows of a viscous liquid in a cylindrical tube and a channel of variable cross-section are studied. A qualitative triangulation of the surface of a cylindrical tube, a smoothed and experimental channel of a variable cross section is constructed. The problem is solved numerically using boundary element method in several modifications for a periodic and non-periodic flows. The obtained numerical results are compared with the analytical solution for the Poiseuille flow.

Pin-Fin Heat Sink With Horizontal Base and Blocked Edges

2008 ◽  
Author(s):  
D. Sahray ◽  
H. Shmueli ◽  
N. Segal ◽  
G. Ziskind ◽  
R. Letan
Keyword(s):  
Heat Transfer ◽  
Free Convection ◽  
Contact Resistance ◽  
Cross Section ◽  
Heat Input ◽  
Heat Sink ◽  
Numerical Study ◽  
Heat Sinks ◽  
Transfer Enhancement ◽  
Pin Fin

In the present work, horizontal-base pin fin heat sinks exposed to free convection in air are studied. They are made of aluminum, and there is no contact resistance between the base and the fins. For the same base dimensions the fin height and pitch vary. The fins have a constant square cross-section. The edges of the sink are blocked: the surrounding insulation is flush with the fin tips. The effect of fin height and pitch on the performance of the sink is studied experimentally and numerically. In the experiments, the heat sinks are heated using foil electrical heaters. The heat input is set, and temperatures of the base and fins are measured. In the corresponding numerical study, the sinks and their environment are modeled using the Fluent 6 software. The results show that heat transfer enhancement due to the fins is not monotonic. The differences between sparsely and densely populated sinks are analyzed for various fin heights. Also assessed are effects of the blocked edges as compared to the previously studied cases where the sink edges were exposed to the surroundings.

scholarly journals NUMERICAL STUDY OF RADIATIVE CORRECTIONS IN THE LOW Q2 REGION AT HERA

1994 ◽  
Vol 09 (18) ◽  
pp. 3229-3244
Author(s):  
K. CHARCHULA ◽  
J. GAJEWSKI
Keyword(s):  
Cross Section ◽  
Numerical Study ◽  
Radiative Corrections ◽  
Hadronic Final State ◽  
Radiative Effects ◽  
Final State ◽  
Cross Section Measurement ◽  
Photoproduction Cross Section ◽  
Section Measurement

A detailed numerical study of radiative corrections in the low Q2 region at the HERA ep collider was performed. The specific case of the total photoproduction cross section measurement was taken as an example. Two different programs, TERAD91 and HER-ACLES4.2, were used to get an estimate of the size of radiative effects. It was found that radiative corrections can be quite large at some points of the space of leptonic (x, y) variables. However, after imposing experimentally feasible cuts on the radiated photon and the hadronic final state one gets corrections at the level of a few per cent.

scholarly journals Steady and unsteady flow of non-newtonian fluid in curved pipe with triangular

2006 ◽  
Vol 3 (3) ◽  
pp. 470-480
Author(s):  
Baghdad Science Journal
Keyword(s):  
Unsteady Flow ◽  
Pressure Gradient ◽  
Secondary Flow ◽  
Cross Section ◽  
Numerical Study ◽  
Equations Of Motion ◽  
Curved Pipe ◽  
First Case ◽  
Stable Flow ◽  
Flow Cross

This paper deals with numerical study of the flow of stable and fluid Allamstqr Aniotina in an area surrounded by a right-angled triangle has touched particularly valuable secondary flow cross section resulting from the pressure gradient In the first case was analyzed stable flow where he found that the equations of motion that describe the movement of the fluid

scholarly journals Experimental and Numerical Study on Ultimate Shear Load Carrying Capacity of Corroded RC Beams

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Zhanzhan Tang ◽  
Zhixiang He ◽  
Zheng Chen ◽  
Lingkun Chen ◽  
Hanyang Xue ◽  
...  
Keyword(s):  
Shear Strength ◽  
Bearing Capacity ◽  
Cross Section ◽  
Loss Rate ◽  
Numerical Study ◽  
Rc Beams ◽  
Load Carrying ◽  
Shear Bearing Capacity ◽  
The Cross ◽  
The Impact

For an RC beam, the strength of steel rebar, the bonding strength between the concrete and reinforcement, and the bite action between the aggregates will deteriorate significantly due to corrosion. In the present study, 10 RC beams were designed to study the impact of corrosion on the shear bearing capacity. The mechanism of corrosion for stirrups and longitudinal bars and their effects were analyzed. Based on the existing experimental data, the correlation between the stirrup corrosion factor and the cross section loss rate was obtained. An effective prediction formula on the shear bearing capacity of the corroded RC beams was proposed and validated by the experimental results. Moreover, a numerical analysis approach based on the FE technique was proposed for the prediction of the shear strength. The results show that corrosion of the reinforcements could reduce the shear strength of the RC beams. The corrosion of stirrups can be numerically simulated by the reduction of the cross section. The formulae in the literature are conservative and the predictions are very dispersed, while the predictions by the proposed formula agree very well with the experiment results.

Sign in / Sign up

Export Citation Format

Share Document