Closed-form approximations of interaction diagrams for assessment and design of reinforced concrete columns and concrete-filled steel tubes with circular cross-section

2016 ◽  
Vol 127 ◽  
pp. 594-601 ◽  
Author(s):  
Francesco Trentadue ◽  
Giuseppe Quaranta ◽  
Giuseppe C. Marano
Keyword(s):  
Reinforced Concrete ◽  
Closed Form ◽  
Cross Section ◽  
Circular Cross Section ◽  
Concrete Columns ◽  
Steel Tubes ◽  
Reinforced Concrete Columns ◽  
Concrete Filled Steel Tubes

STRESS-STRAIN STATE OF ECCENTRICALLY COMPRESSED REINFORCED CONCRETE COLUMNS OF CIRCULAR CROSS-SECTION

2018 ◽  
Vol 8 (1) ◽  
pp. 4-9
Author(s):  
Sergey S. MORDOVSKY ◽  
Rustam I. DAVLIKAMOV
Keyword(s):  
Reinforced Concrete ◽  
Cross Section ◽  
Nonlinear Deformation ◽  
Strain State ◽  
Circular Cross Section ◽  
Concrete Columns ◽  
Deformation Model ◽  
Stress Strain ◽  
Reinforced Concrete Columns ◽  
Nonlinear Deformation Model

Theoretical studies of reinforced concrete eccentrically compressed columns of circular cross-section on strength indexes are analyzed. These studies rely on the use of a nonlinear deformation model that approximates the work of concrete to real experimental conditions. A comparative analysis of the results of calculating the strength of reinforced concrete columns of circular cross-section is carried out according to the methodology proposed in the current set of rules, is the author’s program for determining the stress-strain state of a reinforced concrete column of circular cross-section implemented in the MathCad software environment. The results of a numerical experiment are compared in the form of a fi nite-element model in the Lira-CAD program complex using a nonlinear deformation model. Calculations and schemes are given taking into account the possibility of conducting an experimental study.

SETTING A DIAGRAM APPROACH TO CALCULATING VIBRATED, CENTRIFUGED AND VIBROCENTRIFUGED REINFORCED CONCRETE COLUMNS WITH A VARIATROPIC STRUCTURE

2020 ◽  
pp. 22-34
Author(s):  
Л. Р. Маилян ◽  
С. А. Стельмах ◽  
Е. М. Щербань ◽  
М. П. Нажуев
Keyword(s):  
Experimental Data ◽  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Cross Section ◽  
Concrete Columns ◽  
Reinforced Concrete Columns ◽  
The Cross ◽  
Concrete Elements ◽  
Diagram Approach

Состояние проблемы. Железобетонные элементы изготавливаются, как правило, по трем основным технологиям - вибрированием, центрифугированием и виброцентрифугированием. Однако все основные расчетные зависимости для определения их несущей способности выведены, исходя из основного постулата - постоянства и равенства характеристик бетона по сечению, что реализуется лишь в вибрированных колоннах. Результаты. В рамках диаграммного подхода предложены итерационный, приближенный и упрощенный способы расчета несущей способности железобетонных вибрированных, центрифугированных и виброцентрифугированных колонн. Выводы. Расчет по диаграммному подходу показал существенно более подходящую сходимость с опытными данными, чем расчет по методике норм, а также дал лучшие результаты при использовании дифференциальных характеристик бетона, чем при использовании интегральных и, тем более, нормативных характеристик бетона. Statement of the problem. Reinforced concrete elements are typically manufactured according to three basic technologies - vibration, centrifugation and vibrocentrifugation. However, all the basic calculated dependencies for determining their bearing capacity were derived using the main postulate, i.e., the constancy and equality of the characteristics of concrete over the cross section, which is implemented only in vibrated columns. Results. Within the framework of the diagrammatic approach, iterative, approximate and simplified methods of calculating the bearing capacity of reinforced concrete vibrated, centrifuged and vibrocentrifuged columns are proposed. Conclusions. The calculation according to the diagrammatic approach showed a significantly better convergence with the experimental data than that using the method of norms, and also performs better when using differential characteristics of concrete than when employing integral and particularly standard characteristics of concrete.

scholarly journals Behavior of reinforced concrete columns strenghtened by partial jacketing

2016 ◽  
Vol 9 (1) ◽  
pp. 1-21 ◽  
Author(s):  
D. B. FERREIRA ◽  
R. B. GOMES ◽  
A. L. CARVALHO ◽  
G. N. GUIMARÃES
Keyword(s):  
Reinforced Concrete ◽  
Cross Section ◽  
Rectangular Cross Section ◽  
Concrete Columns ◽  
The Other ◽  
Self Compacting Concrete ◽  
Reinforced Concrete Columns ◽  
Compressive Stresses ◽  
Concrete Layer ◽  
Ultimate Resistance

This article presents the study of reinforced concrete columns strengthened using a partial jacket consisting of a 35mm self-compacting concrete layer added to its most compressed face and tested in combined compression and uniaxial bending until rupture. Wedge bolt connectors were used to increase bond at the interface between the two concrete layers of different ages. Seven 2000 mm long columns were tested. Two columns were cast monolithically and named PO (original column) e PR (reference column). The other five columns were strengthened using a new 35 mm thick self-compacting concrete layer attached to the column face subjected to highest compressive stresses. Column PO had a 120mm by 250 mm rectangular cross section and other columns had a 155 mm by 250mm cross section after the strengthening procedure. Results show that the ultimate resistance of the strengthened columns was more than three times the ultimate resistance of the original column PO, indicating the effectiveness of the strengthening procedure. Detachment of the new concrete layer with concrete crushing and steel yielding occurred in the strengthened columns.

scholarly journals Analysis of the behavior of reinforced concrete columns strengthened with sleeve wedge bolts and a self compacting concrete layer

2015 ◽  
Vol 8 (2) ◽  
pp. 88-99
Author(s):  
M. G. Marques ◽  
A. P. A. R. Liserre ◽  
R. B. Gomes ◽  
G. N. Guimarães
Keyword(s):  
Reinforced Concrete ◽  
Cross Section ◽  
Rectangular Cross Section ◽  
Concrete Columns ◽  
Concrete Surface ◽  
Self Compacting Concrete ◽  
Reinforced Concrete Columns ◽  
Concrete Layer ◽  
Strength Capacity ◽  
Strengthening Technique

Strengthening of reinforced concrete columns by jacketing is one of the most common structural rehabilitation techniques in Brazil. For adequate performance, it is necessary, among others, to avoid detachment of the new concrete layer (strengthening material) from the old concrete substrate when the strengthened member is again in service conditions. This paper describes the test results of eight reinforced concrete rectangular columns subjected to combined compression and one-axis bending to evaluate the efficiency of using sleeve wedge bolts across the new concrete/old concrete interface to avoid detachment. The strengthening technique, in this case, consists of adding a layer of self-compacting concrete to one face of the column. Two columns tested were monolithic and named PO (original column) e PR (reference column). The other six columns were strengthened using a new 35 mm thick self-compacting concrete layer attached to the column face subjected to highest compressive stresses. Column PO had a 120mm by 250 mm rectangular cross section and its results gave information about column behavior without the use of strengthening. Column PR had a 155mm by 250 mm rectangular cross section and its cross section dimensions matched the strengthened columns but it was cast monolithically. To improve bond conditions between the existing concrete and the new concrete, the concrete surface was roughened and the outermost aggregate was exposed using hydro jetting. Holes along the concrete surface were made to insert the wedge bolts responsible for increasing the bond between the two concrete surfaces. The difference among the six strengthened columns was the position and amount of bolts used. Results indicate that the position and amount of the bolts alters significantly the strength capacity of the columns, since premature rupture by concrete detachment was delayed.

scholarly journals Investigation of Parameters Affecting the Equivalent Yield Curvature of Reinforced Concrete Columns

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1594
Author(s):  
Umut Hasgul
Keyword(s):  
Reinforced Concrete ◽  
Cross Section ◽  
Axial Load ◽  
Concrete Columns ◽  
Load Level ◽  
Combined Effects ◽  
Reinforced Concrete Columns ◽  
Independent Effects ◽  
Equivalent Yield ◽  
Section Dimension

In this study, the response quantities affecting the equivalent yield curvature, which is important in the deformation-based seismic design and assessment of structural systems, are investigated for reinforced concrete columns with a square cross-section. In this context, the equivalent yield curvatures were determined by conducting moment–curvature analyses on various column models, in which the axial load level, cross-section dimension, longitudinal reinforcement ratio, and concrete compression strength were changed parametrically, and the independent and/or combined effects of the relevant parameters were discussed. Depending on the axial load levels of P/Agfc′ < 0.3, P/Agfc′ = 0.3, and P/Agfc′ > 0.3 for the considered columns, the yielding of reinforcement, yielding of reinforcement and/or concrete crushing, and concrete crushing governed the yield conditions, respectively. It can be noted that the cross-section dimension and axial load level became the primary parameters. Even though the independent effects with regard to particular parameters remained at minimal levels, the combined effects of them with the axial load became important in terms of the equivalent yield curvature.

scholarly journals Transverse Reinforcement in Reinforced Concrete Columns

2013 ◽  
Vol 8 (2) ◽  
pp. 41-50
Author(s):  
Štefan Gramblička ◽  
Peter Veróny
Keyword(s):  
Reinforced Concrete ◽  
Cross Section ◽  
Concrete Columns ◽  
Transverse Reinforcement ◽  
Transverse Deformation ◽  
Reinforced Concrete Columns

Abstract In the article we are dealing with the influence of transverse reinforcement to the resistance of a cross-section of the reinforced concrete columns and also with the effective detailing of the column reinforcement. We are verifying the correctness of design guides for detailing of transverse reinforcement. We are also taking into account the diameter of stirrups and its influence over transverse deformation of column.

Sign in / Sign up

Export Citation Format

Share Document