Exact matching at a joint of multiply-connected box beams under out-of-plane bending and torsion

2016 ◽  
Vol 124 ◽  
pp. 96-112 ◽  
Author(s):  
Soomin Choi ◽  
Yoon Young Kim
Keyword(s):  
Exact Matching ◽  
Multiply Connected ◽  
Out Of Plane ◽  
Box Beams ◽  
Plane Bending

Exact Matching Condition at a Joint of Thin-Walled Box Beams Under Out-of-Plane Bending and Torsion

2012 ◽  
Vol 79 (5) ◽  
Author(s):  
Soomin Choi ◽  
Gang-Won Jang ◽  
Yoon Young Kim
Keyword(s):  
Beam Theory ◽  
Matching Condition ◽  
Higher Order ◽  
Transformation Matrix ◽  
Exact Matching ◽  
Box Beam ◽  
Out Of Plane ◽  
Box Beams ◽  
Thin Walled ◽  
Plane Bending

To take into account the flexibility resulting from sectional deformations of a thin-walled box beam, higher-order beam theories considering warping and distortional degrees of freedom (DOF) in addition to the Timoshenko kinematic degrees have been developed. The objective of this study is to derive the exact matching condition consistent with a 5-DOF higher-order beam theory at a joint of thin-walled box beams under out-of-plane bending and torsion. Here we use bending deflection, bending/shear rotation, torsional rotation, warping, and distortion as the kinematic variables. Because the theory involves warping and distortion that do not produce any force/moment resultant, the joint matching condition cannot be obtained just by using the typical three equilibrium conditions. This difficulty poses considerable challenges because all elements of the 5×5 transformation matrix relating the field variables of one beam to those in another beam should be determined. The main contributions of the investigation are to propose additional necessary conditions to determine the matrix and to derive it exactly. The validity of the derived joint matching transformation matrix is demonstrated by showing good agreement between the shell finite element results and those obtained by the present box beam analysis in various angle box beams.

Comparison of Failure Modes of Piping Systems With Wall Thinning Subjected to In-Plane, Out-of-Plane, and Mixed Mode Bending Under Seismic Load: An Experimental Approach

2010 ◽  
Vol 132 (3) ◽  
Author(s):  
Izumi Nakamura ◽  
Akihito Otani ◽  
Masaki Shiratori
Keyword(s):  
Dynamic Behavior ◽  
Failure Modes ◽  
Seismic Load ◽  
Piping System ◽  
Shake Table ◽  
Shake Table Tests ◽  
Wall Thinning ◽  
Piping Systems ◽  
Out Of Plane ◽  
Plane Bending

Pressurized piping systems used for an extended period may develop degradations such as wall thinning or cracks due to aging. It is important to estimate the effects of degradation on the dynamic behavior and to ascertain the failure modes and remaining strength of the piping systems with degradation through experiments and analyses to ensure the seismic safety of degraded piping systems under destructive seismic events. In order to investigate the influence of degradation on the dynamic behavior and failure modes of piping systems with local wall thinning, shake table tests using 3D piping system models were conducted. About 50% full circumferential wall thinning at elbows was considered in the test. Three types of models were used in the shake table tests. The difference of the models was the applied bending direction to the thinned-wall elbow. The bending direction considered in the tests was either of the in-plane bending, out-of-plane bending, or mixed bending of the in-plane and out-of-plane. These models were excited under the same input acceleration until failure occurred. Through these tests, the vibration characteristic and failure modes of the piping models with wall thinning under seismic load were obtained. The test results showed that the out-of-plane bending is not significant for a sound elbow, but should be considered for a thinned-wall elbow, because the life of the piping models with wall thinning subjected to out-of-plane bending may reduce significantly.

Stresses in Curved, Circular Thin-Wall Tubes

1963 ◽  
Vol 30 (1) ◽  
pp. 134-135
Author(s):  
E. A. Utecht
Keyword(s):  
Thin Wall ◽  
Bending Moments ◽  
Circular Tubes ◽  
Out Of Plane ◽  
Thin Walled ◽  
Plane Bending

Curves are presented which give stress intensification factors for curved, thin-walled circular tubes under various combinations of in-plane and out-of-plane bending moments.

Sign in / Sign up

Export Citation Format

Share Document