The influence of reinforcement on load carrying capacity and cracking of the reinforced concrete deep beam joint

2016 ◽  
Vol 107 ◽  
pp. 23-33 ◽  
Author(s):  
Anna Kopańska ◽  
Krystyna Nagrodzka-Godycka
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Load Carrying Capacity ◽  
Deep Beam ◽  
Load Carrying

scholarly journals Effect of Size and Location of Square Web Openings on the Entire Behavior of Reinforced Concrete Deep Beams

2019 ◽  
Vol 5 (1) ◽  
pp. 209 ◽  
Author(s):  
Waleed A. Jasim ◽  
Abbas A. Allawi ◽  
Nazar Kamil Ali Oukaili
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Shear Capacity ◽  
Load Carrying Capacity ◽  
Deep Beam ◽  
Deep Beams ◽  
Web Openings ◽  
Shear Span ◽  
Load Carrying

This paper presents an experimental and numerical study which was carried out to examine the influence of the size and the layout of the web openings on the load carrying capacity and the serviceability of reinforced concrete deep beams. Five full-scale simply supported reinforced concrete deep beams with two large web openings created in shear regions were tested up to failure. The shear span to overall depth ratio was (1.1). Square openings were located symmetrically relative to the midspan section either at the midpoint or at the interior boundaries of the shear span. Two different side dimensions for the square openings were considered, mainly, (200) mm and (230) mm. The strength results proved that the shear capacity of the deep beam is governed by the size and location of web openings. The experimental results indicated that the reduction of the shear capacity may reach (66%). ABAQUS finite element software program was used for simulation and analysis. Numerical analyses provided un-conservative estimates for deep beam load carrying capacity in the range between (5-21%). However, the maximum scatter of the finite element method predictions for first diagonal and first flexural cracking loads was not exceeding (17%). Also, at service load the numerical of midspan deflection was greater than the experimental values by (9-18%).

scholarly journals Strengthening of Reinforced Concrete Beams Subjected to Concentrated Loads

2022 ◽  
Author(s):  
Paolo Foraboschi
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Concrete Beams ◽  
Shear Capacity ◽  
Reinforced Concrete Beams ◽  
Load Carrying Capacity ◽  
Reinforced Concrete Structure ◽  
Concentrated Loads ◽  
Concentrated Load ◽  
Load Carrying

Renovation, restoration, remodeling, refurbishment, and retrofitting of build-ings often imply modifying the behavior of the structural system. Modification sometimes includes applying forces (i.e., concentrated loads) to beams that before were subjected to distributed loads only. For a reinforced concrete structure, the new condition causes a beam to bear a concentrated load with the crack pattern that was produced by the distributed loads that acted in the past. If the concentrated load is applied at or near the beam’s midspan, the new shear demand reaches the maximum around the midspan. But around the midspan, the cracks are vertical or quasi-vertical, and no inclined bar is present. So, the actual shear capacity around the midspan not only is low, but also can be substantially lower than the new demand. In order to bring the beam capacity up to the demand, fiber-reinforced-polymer composites can be used. This paper presents a design method to increase the concentrated load-carrying capacity of reinforced concrete beams whose load distribution has to be changed from distributed to concentrated, and an analytical model to pre-dict the concentrated load-carrying capacity of a beam in the strengthened state.

scholarly journals Flexural strengthening of Reinforced Concrete (RC) Beams Retrofitted with Corrugated Glass Fiber Reinforced Polymer (GFRP) Laminates

2015 ◽  
Vol 2 (1) ◽  
Author(s):  
N. Aravind ◽  
Amiya K. Samanta ◽  
Dilip Kr. Singha Roy ◽  
Joseph V. Thanikal
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Fiber Reinforced Polymer ◽  
Load Carrying Capacity ◽  
Rc Beams ◽  
Glass Fiber Reinforced Polymer ◽  
Flexural Strengthening ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced ◽  
Load Carrying

AbstractStrengthening the structural members of old buildings using advanced materials is a contemporary research in the field of repairs and rehabilitation. Many researchers used plain Glass Fiber Reinforced Polymer (GFRP) sheets for strengthening Reinforced Concrete (RC) beams. In this research work, rectangular corrugated GFRP laminates were used for strengthening RC beams to achieve higher flexural strength and load carrying capacity. Type and dimensions of corrugated profile were selected based on preliminary study using ANSYS software. A total of twenty one beams were tested to study the load carrying capacity of control specimens and beams strengthened with plain sheets and corrugated laminates using epoxy resin. This paper presents the experimental and theoretical study on flexural strengthening of Reinforced Concrete (RC) beams using corrugated GFRP laminates and the results are compared. Mathematical models were developed based on the experimental data and then the models were validated.

scholarly journals Rebars for Durable Concrete Construction: Points to Ponder

2021 ◽  
Author(s):  
Anil K. Kar
Keyword(s):  
Reinforced Concrete ◽  
Carbon Steel ◽  
Carrying Capacity ◽  
High Strength Steel ◽  
Global Climate ◽  
High Strength ◽  
Load Carrying Capacity ◽  
Glass Fiber Reinforced ◽  
Load Carrying ◽  
Total Failure

Reinforced concrete is the number one medium of construction. It is important to have good quality concrete and reinforcing bar (rebar). It is equally important to have competent bond between rebar and concrete. About six decades ago ribbed rebars of high strength steel started replacing plain round bars of mild steel, the use of which had made reinforced concrete constructions durable. It was overlooked that ribbed rebars of carbon steel would be highly susceptible to corrosion at accelerated rates. That would not only make reinforced concrete constructions reach states of distress early, that could also destroy or reduce bond between ribbed rebars and concrete. The continued use of ribbed rebars of high strength carbon steel demonstrates a widespread lack of understanding of the phenomenon of bond between rebars and concrete. This lack of understanding of bond has led to the introduction of epoxy coated ribbed rebars, ribbed stainless steel bars and glass fiber reinforced and granite reinforced polymer rebars, all of which permit reinforced concrete carry static loads because of engagement between such rebars and concrete. But the load-carrying capacity of reinforced concrete elements is impaired, and such elements become vulnerable to local or even total failure during vibratory loads. The use of PSWC-BAR, characterized by its plain surface and wave-type configuration, permits the use of medium strength and high strength steel. In the absence of ribs, the rate of corrosion is greatly reduced. The use of PSWC-BARs, at no added effort or cost, in lieu of conventional ribbed bars, leads to enhancement of effective bond or engagement between such rebars and concrete, thereby leading to increased load-carrying capacity, several-fold higher life span, ductility and energy-absorbing capacity, and great reduction in life cycle cost and adverse impact of construction on the environment and the global climate. In keeping with a lack of understanding of bond between rebars and concrete, there is arbitrariness in the selection of the required level of percent elongation and ductility of rebars.

Guidelines for flexural design of FRP reinforced concrete beams

2020 ◽  
pp. 002199832097373
Author(s):  
Fares Jnaid
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Concrete Beams ◽  
Large Diameter ◽  
Reinforced Concrete Beams ◽  
Load Carrying Capacity ◽  
Concrete Compressive Strength ◽  
Load Carrying ◽  
Multiple Variables

This paper investigates the effects of different parameters on the live load carrying capacity of concrete beams reinforced with FRP bars. The author performed a parametric study utilizing an innovative numerical approach to inspect the effects of multiple variables such as reinforcement ratio, concrete compressive strength, span to depth ratio, FRP type, and bar diameter on load carrying capacity of FRP reinforced concrete beams. This study concluded that unless the span to height ratio is smaller than 8, tension-controlled sections are impractical as they do not meet code requirements for serviceability. In addition, it is recommended to use higher reinforcement ratios when using larger span to depth ratios and/or when using CFRP reinforcing bars. Moreover, larger number of bars with small diameter is more practical than fewer large diameter bars. Furthermore, this research suggests that increasing the concrete compressive strength is associated with a significant increase in the ultimate flexural capacity of FRP reinforced beams.

Sign in / Sign up

Export Citation Format

Share Document