Extended sandwich model for reinforced concrete slabs: Shear strength with transverse reinforcement

2014 ◽  
Vol 74 ◽  
pp. 218-228 ◽  
Author(s):  
Thomas Jaeger
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Concrete Slabs ◽  
Transverse Reinforcement ◽  
Reinforced Concrete Slabs ◽  
Sandwich Model

Critical shear crack theory-based punching shear model for FRP-reinforced concrete slabs

2020 ◽  
pp. 136943322097814
Author(s):  
Xing-lang Fan ◽  
Sheng-jie Gu ◽  
Xi Wu ◽  
Jia-fei Jiang
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Shear Crack ◽  
Concrete Strength ◽  
Weight Ratio ◽  
Punching Shear ◽  
Concrete Slabs ◽  
Crack Theory ◽  
Reinforced Concrete Slabs ◽  
Rc Slabs

Owing to their high strength-to-weight ratio, superior corrosion resistance, and convenience in manufacture, fiber-reinforced polymer (FRP) bars can be used as a good alternative to steel bars to solve the durability issue in reinforced concrete (RC) structures, especially for seawater sea-sand concrete. In this paper, a theoretical model for predicting the punching shear strength of FRP-RC slabs is developed. In this model, the punching shear strength is determined by the intersection of capacity and demanding curve of FRP-RC slabs. The capacity curve is employed based on critical shear crack theory, while the demand curve is derived with the help of a simplified tri-linear moment-curvature relationship. After the validity of the proposed model is verified with experimental data collected from the literature, the effects of concrete strength, loading area, FRP reinforcement ratio, and effective depth of concrete slabs are evaluated quantitatively.

Critical Review of Design Procedures for Reinforced Concrete Slabs as per IRC 112-2011

2019 ◽  
Vol 969 ◽  
pp. 349-354 ◽  
Author(s):  
J. Chithra ◽  
Praveen Nagarajan ◽  
A.S. Sajith ◽  
R.A. Roshan
Keyword(s):  
Reinforced Concrete ◽  
Critical Review ◽  
Concrete Slab ◽  
Concrete Slabs ◽  
Reinforced Concrete Slab ◽  
Finite Element Software ◽  
Reinforced Concrete Slabs ◽  
Distributed Load ◽  
Uniformly Distributed Load ◽  
Sandwich Model

Nowadays finite element software is used for the design and analysis of reinforced concrete slabs. This paper intends to have a critical review based on a comparison study between the three design methods and to estimate the amount of reinforcement to be provided in each case. The three methods discussed are; the three-layer sandwich model (IRC 112-2011), Wood Armer method (EN1992-1-1:2004) and the conventional design method as per IS 456-2000. In the recently revised code for bridges IRC 112-2011, there is a recommendation to adopt three-layer sandwich model for the design of reinforced concrete slab. In this paper, a critical review of this method is done, and it is used for slabs subjected to uniformly distributed load. This method is illustrated by considering the design of rectangular slab subjected to uniformly distributed load. The results of this method are compared with the results obtained using Wood Armer method and using the moment coefficients suggested in IS 456-2000.

Punching shear strength of reinforced concrete slabs with plastic void formers

2017 ◽  
Vol 145 ◽  
pp. 518-527 ◽  
Author(s):  
Juozas Valivonis ◽  
Tomas Skuturna ◽  
Mykolas Daugevičius ◽  
Arnoldas Šneideris
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Punching Shear ◽  
Concrete Slabs ◽  
Reinforced Concrete Slabs

scholarly journals Evaluation of punching shear strength of flat slabs supported on rectangular columns

2018 ◽  
Vol 33 ◽  
pp. 02007 ◽  
Author(s):  
Valery Filatov
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Concrete Slab ◽  
Structural Parameters ◽  
Experimental Studies ◽  
Punching Shear ◽  
Design Solution ◽  
Concrete Slabs ◽  
Reinforced Concrete Slabs ◽  
Rectangular Columns

The article presents the methodology and results of an analytical study of structural parameters influence on the value of punching force for the joint of columns and flat reinforced concrete slab. This design solution is typical for monolithic reinforced concrete girderless frames, which have a wide application in the construction of high-rise buildings. As the results of earlier studies show the punching shear strength of slabs at rectangular columns can be lower than at square columns with a similar length of the control perimeter. The influence of two structural parameters on the punching strength of the plate is investigated - the ratio of the side of the column cross-section to the effective depth of slab C/d and the ratio of the sides of the rectangular column Cmax/Cmin. According to the results of the study, graphs of reduction the control perimeter depending on the structural parameters are presented for columns square and rectangular cross-sections. Comparison of results obtained by proposed approach and MC2010 simplified method are shown, that proposed approach gives a more conservative estimate of the influence of the structural parameters. A significant influence of the considered structural parameters on punching shear strength of reinforced concrete slabs is confirmed by the results of experimental studies. The results of the study confirm the necessity of taking into account the considered structural parameters when calculating the punching shear strength of flat reinforced concrete slabs and further development of code design methods.

scholarly journals Consideration on punching shear strength of steel-fiber-reinforced concrete slabs

2015 ◽  
Vol 7 (5) ◽  
pp. 168781401558425 ◽  
Author(s):  
Hyunjin Ju ◽  
Na-Rae Cheon ◽  
Deuck Hang Lee ◽  
Jae-Yuel Oh ◽  
Jin-Ha Hwang ◽  
...  
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Steel Fiber ◽  
Fiber Reinforced Concrete ◽  
Punching Shear ◽  
Concrete Slabs ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Reinforced Concrete Slabs
Sign in / Sign up

Export Citation Format

Share Document