Parametric study on the thermal response of curved integral abutment bridges

2012 ◽  
Vol 43 ◽  
pp. 129-138 ◽  
Author(s):  
Emre Kalayci ◽  
Scott A. Civjan ◽  
Sergio F. Breña
Keyword(s):  
Parametric Study ◽  
Thermal Response ◽  
Integral Abutment ◽  
Integral Abutment Bridges ◽  
Abutment Bridges

Simple Approach to Calculate Displacements and Rotations in Integral Abutment Bridges

2015 ◽  
Vol 2522 (1) ◽  
pp. 39-46 ◽  
Author(s):  
Suhail Albhaisi ◽  
Hani Nassif
Keyword(s):  
Parametric Study ◽  
Thermal Loading ◽  
Three Dimensional ◽  
Field Measurements ◽  
Simple Approach ◽  
Fe Model ◽  
Integral Abutment ◽  
Foundation Soil ◽  
Integral Abutment Bridges ◽  
Abutment Bridges

This paper presents a simple approach to calculate the displacements and the rotations induced by thermal loading in integral abutment bridges (IABs). The approach was derived from the results of a parametric study that investigated the effect of substructure stiffness on the performance of short- and medium-length steel IABs built on clay and sand under thermal load effects. Various parameters, such as pile size and orientation, pile material, and foundation soil stiffness, were considered in the study. Detailed three-dimensional (3-D) finite element (FE) models using the software LUSAS were developed to capture the overall behavior of IABs. The developed 3-D FE model was calibrated with field measurements obtained from a previous study. A parametric study was carried out with the calibrated models to study the effects of the above parameters on the performance of IABs under thermal loading using the AASHTO load and resistance factor design temperature ranges. The study showed that most parameters have significant effects on the displacement and rotation of the abutment and the supporting piles. Also, for relatively wide IABs, there were significant variations in the displacement and rotations in the substructure elements between interior and exterior locations. This approach, which used simple equations and charts and included parameters such as the length of the bridge, the stiffness of the foundation soil, and the pile location, provided results that were comparable with those of a detailed FE analysis.

Parametric Study of Concrete Integral Abutment Bridges

2008 ◽  
Vol 13 (5) ◽  
pp. 511-526 ◽  
Author(s):  
Jimin Huang ◽  
Carol K. Shield ◽  
Catherine E. W. French
Keyword(s):  
Parametric Study ◽  
Integral Abutment ◽  
Integral Abutment Bridges ◽  
Abutment Bridges

Parametric Study on the Approach Problem of an Integral Abutment Bridge Subjected to Cyclic Loading due to Temperature Changes

2016 ◽  
Vol 846 ◽  
pp. 421-427
Author(s):  
Ahmed S. Alqarawi ◽  
Chin J. Leo ◽  
D.S. Liyanapathirana ◽  
Sanka Ekanayake
Keyword(s):  
Parametric Study ◽  
Earth Pressure ◽  
Expanded Polystyrene ◽  
Integral Abutment ◽  
Bridge Abutments ◽  
Integral Abutment Bridges ◽  
Expansion Joints ◽  
Temperature Changes ◽  
Abutment Bridges ◽  
Lateral Earth Pressure

Integral Abutment Bridges are widely utilized around the world because they offer a design alternative minimizing the potential construction and maintenance difficulties associated with expansion joints in other types of bridges. However, integral bridge systems also have certain issues that result from the absence of expansion joints. This is because temperature changes induce cycles of elongations and shortenings in the bridge deck which lead to rotational movements in bridge abutments against and away from the retained soil. This phenomenon may develop long term problems in terms of settlement of the backfill at the bridge approach and escalation in the lateral earth pressure acting on the bridge abutments. This paper aims to investigate the approach settlement and lateral earth pressure development in integral bridges abutments using finite element modelling of a concrete bridge abutment and the adjoining soil using the ABAQUS software. The paper presents a parametric study of the effects imposed by abutment movements on the retained soil. This study also investigates the effectiveness of using expanded polystyrene (EPS) geofoam inclusions as a remedial measure to minimize the approach settlement and lateral stress ratcheting effects in Integral Abutment Bridges.

scholarly journals Influence of Construction Joint and Bridge Geometry on Integral Abutment Bridges

2021 ◽  
Vol 11 (11) ◽  
pp. 5031
Author(s):  
Wooseok Kim ◽  
Jeffrey A. Laman ◽  
Farzin Zareian ◽  
Geunhyung Min ◽  
Do Hyung Lee
Keyword(s):  
Prestressed Concrete ◽  
Extreme Temperature ◽  
Bending Moment ◽  
Design Guidelines ◽  
Time Dependent ◽  
Steel Bridge ◽  
Integral Abutment ◽  
Integral Abutment Bridges ◽  
Construction Joint ◽  
Abutment Bridges

Although integral abutment bridges (IABs) have become a preferred construction choice for short- to medium-length bridges, they still have unclear bridge design guidelines. As IABs are supported by nonlinear boundaries, bridge geometric parameters strongly affect IAB behavior and complicate predicting the bridge response for design and assessment purposes. This study demonstrates the effect of four dominant parameters: (1) girder material, (2) bridge length, (3) backfill height, and (4) construction joint below girder seats on the response of IABs to the rise and fall of AASHTO extreme temperature with time-dependent effects in concrete materials. The effect of factors influencing bridge response, such as (1) bridge construction timeline, (2) concrete thermal expansion coefficient, (3) backfill stiffness, and (4) pile-soil stiffness, are assumed to be constant. To compare girder material and bridge geometry influence, the study evaluates four critical superstructure and substructure response parameters: (1) girder axial force, (2) girder bending moment, (3) pile moment, and (4) pile head displacement. All IAB bridge response values were strongly related to the four considered parameters, while they were not always linearly proportional. Prestressed concrete (PSC) bridge response did not differ significantly from the steel bridge response. Forces and moments in the superstructure and the substructure induced by thermal movements and time-dependent loads were not negligible and should be considered in the design process.

Behaviour of H-piles supporting an integral abutment bridge

2014 ◽  
Vol 51 (7) ◽  
pp. 713-734 ◽  
Author(s):  
Shelley A. Huntley ◽  
Arun J. Valsangkar
Keyword(s):  
Axial Load ◽  
Integral Abutment ◽  
Integral Abutment Bridges ◽  
Expansion Joints ◽  
Thermal Bridge ◽  
Double Curvature ◽  
Abutment Bridges ◽  
Integral Abutments ◽  
Integral Abutment Bridge ◽  
Lateral Displacements

Integral abutment bridges accommodate thermal superstructure movements through flexible foundations rather than expansion joints. While these structures are a common alternative to conventional design, the literature on measured field stresses in piles supporting integral abutments appears to be quite limited. Therefore, field data from strain gauges installed on the abutment foundation piles of a 76 m long; two-span integral abutment bridge are the focus of this paper. Axial load, weak- and strong-axis bending moments of the foundation piles, as well as abutment movement and backfill response, are presented and discussed. Results indicate that the abutment foundation piles are bending in double curvature about the weak axis, as a result of thermal bridge movements, and bending also about the strong axis due to tilting of the abutments. A simple subgrade modulus approach is used to show its applicability in predicting behaviour under lateral loading. In the past, much emphasis has been placed on the lateral displacements of piles and less on variations of axial load. In this paper, a new hypothesis, which offers insight into the mechanisms behind the observed thermal variations in axial load, is proposed and assessed. The data from the field monitoring are also compared with the limited data reported in the literature.

Sign in / Sign up

Export Citation Format

Share Document