The influence of the stress–strain behavior of non-cohesive soils on the geometry of shear band systems under extensional strain

2006 ◽  
Vol 28 (13) ◽  
pp. 1760-1773 ◽  
Author(s):  
H. Wolf ◽  
D. König ◽  
Th. Triantafyllidis
Keyword(s):  
Shear Band ◽  
Cohesive Soils ◽  
Stress Strain ◽  
Strain Behavior ◽  
Extensional Strain

Effect of OCR on sampling disturbance of cohesive soils and evaluation of laboratory reconsolidation procedures

2005 ◽  
Vol 42 (2) ◽  
pp. 459-474 ◽  
Author(s):  
Marika Santagata ◽  
John T Germaine
Keyword(s):  
Effective Means ◽  
Triaxial Tests ◽  
Single Element ◽  
Cohesive Soils ◽  
Stress Strain ◽  
Overconsolidation Ratio ◽  
Strain Behavior ◽  
Preconsolidation Pressure ◽  
Strength Behavior ◽  
Undrained Strength

The paper presents the results of an experimental investigation of sampling disturbance in cohesive soils through single-element triaxial tests on resedimented Boston blue clay (RBBC). The first part of the paper discusses the effect of the overconsolidation ratio (OCR) (1–8) of the soil on postdisturbance compression and undrained shear behavior. The results demonstrate that sensitivity to disturbance decreases markedly with OCR. It is also found that for the medium-sensitivity soil tested, the estimate of the preconsolidation pressure is not significantly affected by OCR. The second part of the paper discusses laboratory reconsolidation procedures. For OCR1 RBBC, the recompression method is not effective in recovering the stress–strain behavior of the soil and, for greater disturbance, provides an increasingly unsafe estimate of the strength. For OCR4, provided the reconsolidation path reproduces the path that occurred in the field, this procedure succeeds in recovering the intact stress–strain–strength behavior of the soil. SHANSEP reconsolidation was investigated for normally consolidated RBBC only. For modest levels of disturbance, this is an effective means of evaluating both the stress–strain and the strength behavior of the soil. For greater levels of disturbance, the stress–strain behavior is not fully recovered, but the method continues to provide conservative estimates of the undrained strength.Key words: sampling disturbance, clays, overconsolidation ratio, undrained strength, recompression, SHANSEP.

Experimental Study of Dynamic Resilient Modulus of Cohesive Soils in Henan

2014 ◽  
Vol 971-973 ◽  
pp. 2092-2095
Author(s):  
Yu Peng Wang ◽  
Liang Zhou
Keyword(s):  
Experimental Study ◽  
Resilient Modulus ◽  
Henan Province ◽  
Additional Analysis ◽  
Cohesive Soils ◽  
Test Results ◽  
Stress Strain ◽  
Strain Behavior ◽  
The Past ◽  
Subgrade Soil

Subgrade soil is very important materials to support highways. Resilient modulus (MR) has been used for characterizing stress-strain behavior of base or subbase subjected to repeated traffic loadings. Several methods to estimate the resilient modulus were suggested in the past years. The main objective of this study was to test the resilient modulus in the laboratory. The Subgrade soil was selected in Henan province. Resilient modulus tests were conducted with UTM. Additional analysis was performed to discuss the factors of the test results.

Stress Strain Behavior of Steel Fibre Based Concrete in Compression

2012 ◽  
Vol 1 (3) ◽  
pp. 32-38
Author(s):  
Tantary M.A ◽  
◽  
Upadhyay A ◽  
Prasad J ◽  
◽  
...  
Keyword(s):  
Steel Fibre ◽  
Stress Strain ◽  
Strain Behavior

Cord/Rubber Material Properties

1985 ◽  
Vol 58 (4) ◽  
pp. 830-856 ◽  
Author(s):  
R. J. Cembrola ◽  
T. J. Dudek
Keyword(s):  
Finite Element ◽  
Material Model ◽  
Rubber Composites ◽  
Stress Strain ◽  
Element Analysis ◽  
Rubber Layer ◽  
Strain Behavior ◽  
Nonlinear Stress ◽  
Interlaminar Shear ◽  
Mechanics Of Composite Materials

Abstract Recent developments in nonlinear finite element methods (FEM) and mechanics of composite materials have made it possible to handle complex tire mechanics problems involving large deformations and moderate strains. The development of an accurate material model for cord/rubber composites is a necessary requirement for the application of these powerful finite element programs to practical problems but involves numerous complexities. Difficulties associated with the application of classical lamination theory to cord/rubber composites were reviewed. The complexity of the material characterization of cord/rubber composites by experimental means was also discussed. This complexity arises from the highly anisotropic properties of twisted cords and the nonlinear stress—strain behavior of the laminates. Micromechanics theories, which have been successfully applied to hard composites (i.e., graphite—epoxy) have been shown to be inadequate in predicting some of the properties of the calendered fabric ply material from the properties of the cord and rubber. Finite element models which include an interply rubber layer to account for the interlaminar shear have been shown to give a better representation of cord/rubber laminate behavior in tension and bending. The application of finite element analysis to more refined models of complex structures like tires, however, requires the development of a more realistic material model which would account for the nonlinear stress—strain properties of cord/rubber composites.

Compressive stress–strain behavior of steel fiber reinforced-recycled aggregate concrete

2014 ◽  
Vol 46 ◽  
pp. 65-72 ◽  
Author(s):  
Jodilson Amorim Carneiro ◽  
Paulo Roberto Lopes Lima ◽  
Mônica Batista Leite ◽  
Romildo Dias Toledo Filho
Keyword(s):  
Compressive Stress ◽  
Steel Fiber ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Fiber Reinforced ◽  
Stress Strain ◽  
Aggregate Concrete ◽  
Strain Behavior
Sign in / Sign up

Export Citation Format

Share Document