Iodide/triiodide electrochemistry in ionic liquids: Effect of viscosity on mass transport, voltammetry and scanning electrochemical microscopy

2011 ◽  
Vol 56 (28) ◽  
pp. 10313-10320 ◽  
Author(s):  
Andinet Ejigu ◽  
Kevin R.J. Lovelock ◽  
Peter Licence ◽  
Darren A. Walsh
Keyword(s):  
Ionic Liquids ◽  
Mass Transport ◽  
Scanning Electrochemical Microscopy ◽  
Electrochemical Microscopy

Effect of Viscosity on Steady-State Voltammetry and Scanning Electrochemical Microscopy in Room Temperature Ionic Liquids

2010 ◽  
Vol 114 (13) ◽  
pp. 4442-4450 ◽  
Author(s):  
Kevin R. J. Lovelock ◽  
Frances N. Cowling ◽  
Alasdair W. Taylor ◽  
Peter Licence ◽  
Darren A. Walsh
Keyword(s):  
Ionic Liquids ◽  
Steady State ◽  
Room Temperature ◽  
Scanning Electrochemical Microscopy ◽  
Room Temperature Ionic Liquids ◽  
Electrochemical Microscopy

Prospects for the Application of Scanning Electrochemical Microscopy in Ionic Liquids

2007 ◽  
Vol 60 (1) ◽  
pp. 29 ◽  
Author(s):  
Maurizio Carano ◽  
Alan M. Bond
Keyword(s):  
Ionic Liquid ◽  
Ionic Liquids ◽  
Steady State ◽  
Aqueous Media ◽  
Scanning Electrochemical Microscopy ◽  
State Theory ◽  
Glass Substrates ◽  
State Behaviour ◽  
Ag Substrate ◽  
Electrochemical Microscopy

Prospects have been assessed for the application of the technique of scanning electrochemical microscopy (SECM) in viscous ionic liquids. Use of the Fc0/+ redox couple (Fc = ferrocene) to obtain microelectrode approach curves revealed that the required steady state behaviour needed for analysis of data relevant to conducting platinum and insulating glass substrates is moderately easy to achieve in a 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM][BF4]) ionic liquid. However, in the more highly viscous 1-butyl-3-methylimidazolium hexafluorophosphate ionic liquid, where significantly lower diffusion coefficients are encountered, approach-curve data that conform to steady state theory are only found with very small microelectrodes (e.g., ≤2 μm diameter), very slow electrode–substrate approach rates (e.g., ≤0.05 μm s–1), and long equilibration times (e.g., 50 s). A comparison is provided with SECM approach curves acquired in aqueous media. SECM images of an Ag substrate in contact with [BMIM][BF4] also are presented and are of only slightly inferior quality to images obtained in water.

Mass Transport in Porous Electrodes Studied by Scanning Electrochemical Microscopy: Example of Nanoporous Gold

2019 ◽  
Vol 6 (12) ◽  
pp. 3160-3166 ◽  
Author(s):  
Mareike Haensch ◽  
Luis Balboa ◽  
Matthias Graf ◽  
Alex Ricardo Silva Olaya ◽  
Jörg Weissmüller ◽  
...  
Keyword(s):  
Mass Transport ◽  
Scanning Electrochemical Microscopy ◽  
Porous Electrodes ◽  
Nanoporous Gold ◽  
Electrochemical Microscopy

scholarly journals Use of Amperometric and Potentiometric Probes in Scanning Electrochemical Microscopy for the Spatially-Resolved Monitoring of Severe Localized Corrosion Sites on Aluminum Alloy 2098-T351

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1132 ◽  
Author(s):  
Rejane M. P. da Silva ◽  
Javier Izquierdo ◽  
Mariana X. Milagre ◽  
Abenchara M. Betancor-Abreu ◽  
Isolda Costa ◽  
...  
Keyword(s):  
Scanning Electrochemical Microscopy ◽  
Oxygen Depletion ◽  
Localized Corrosion ◽  
Alloy Surface ◽  
Al Alloy ◽  
Spatially Resolved ◽  
Lower Oxygen ◽  
Local Ph ◽  
Electrochemical Microscopy

Amperometric and potentiometric probes were employed for the detection and characterization of reactive sites on the 2098-T351 Al-alloy (AA2098-T351) using scanning electrochemical microscopy (SECM). Firstly, the probe of concept was performed on a model Mg-Al galvanic pair system using SECM in the amperometric and potentiometric operation modes, in order to address the responsiveness of the probes for the characterization of this galvanic pair system. Next, these sensing probes were employed to characterize the 2098-T351 alloy surface immersed in a saline aqueous solution at ambient temperature. The distribution of reactive sites and the local pH changes associated with severe localized corrosion (SLC) on the alloy surface were imaged and subsequently studied. Higher hydrogen evolution, lower oxygen depletion and acidification occurred at the SLC sites developed on the 2098-T351 Al-alloy.

Local electrochemical activity of transition metal dichalcogenides and their heterojunctions on 3D-printed nanocarbon surfaces

Nanoscale ◽  
2021 ◽  
Author(s):  
Katarina A. Novčić ◽  
Christian Iffelsberger ◽  
Siowwoon Ng ◽  
Martin Pumera
Keyword(s):  
Transition Metal ◽  
Electrochemical Performance ◽  
Transition Metal Dichalcogenides ◽  
Scanning Electrochemical Microscopy ◽  
Electrochemical Activity ◽  
Thermally Activated ◽  
Metal Dichalcogenides ◽  
3D Printed ◽  
Electrochemical Microscopy

MoS2 and WS2 and their heterojunctions are used to modify thermally activated 3D-printed nanocarbon structures. Herein, the local electrochemical performance for HER of the modified structures is demonstrated by scanning electrochemical microscopy.

scholarly journals Simultaneous Intelligent Imaging of Nanoscale Reactivity and Topography by Scanning Electrochemical Microscopy

2021 ◽  
Author(s):  
Dylan T. Jantz ◽  
Ryan J. Balla ◽  
Siao-Han Huang ◽  
Niraja Kurapati ◽  
Shigeru Amemiya ◽  
...  
Keyword(s):  
Scanning Electrochemical Microscopy ◽  
Electrochemical Microscopy
Sign in / Sign up

Export Citation Format

Share Document