Analytical solutions for laminated beams subjected to non-uniform temperature boundary conditions

2021 ◽  
pp. 115044
Author(s):  
Hai Qian ◽  
Yuexiang Qiu ◽  
Chunhua Lu ◽  
Xin Sha
Keyword(s):  
Boundary Conditions ◽  
Analytical Solutions ◽  
Uniform Temperature ◽  
Laminated Beams ◽  
Temperature Boundary

Sidewall finite-conductivity effects in confined turbulent thermal convection

2002 ◽  
Vol 473 ◽  
pp. 201-210 ◽  
Author(s):  
ROBERTO VERZICCO
Keyword(s):  
Boundary Conditions ◽  
Thermal Convection ◽  
Lateral Wall ◽  
Finite Conductivity ◽  
Mean Flow ◽  
Number Range ◽  
Additional Heat ◽  
Low Aspect Ratio ◽  
Temperature Boundary ◽  
The Mean

The effects of a sidewall with finite thermal conductivity on confined turbulent thermal convection has been investigated using direct numerical simulation. The study is motivated by the observation that the heat flowing through the lateral wall is not always negligible in the low-aspect-ratio cells of several recent experiments. The extra heat flux modifies the temperature boundary conditions of the flow and therefore the convective heat transfer. It has been found that, for usual sidewall thicknesses, the heat travelling from the hot to the cold plates directly through the sidewall is negligible owing to the additional heat exchanged at the lateral fluid/wall interface. In contrast, the modified temperature boundary conditions alter the mean flow yielding significant Nusselt number corrections which, in the low Rayleigh number range, can change the exponent of the Nu vs. Ra power law by 10%.

Laminar Forced Convection in Annular Microchannels With Slip Flow Regime

2009 ◽  
Author(s):  
Arman Sadeghi ◽  
Abolhassan Asgarshamsi ◽  
Mohammad Hassan Saidi
Keyword(s):  
Nusselt Number ◽  
Fluid Flow ◽  
Aspect Ratio ◽  
Boundary Conditions ◽  
Knudsen Number ◽  
Gas Flow ◽  
Slip Flow ◽  
Outer Wall ◽  
Graphical Form ◽  
Uniform Temperature

Fluid flow and heat transfer at microscale have attracted an important research interest in recent years due to the rapid development of microelectromechanical systems (MEMS). Fluid flow in microdevices has some characteristics which one of them is rarefaction effect related with gas flow. In this research, hydrodynamically and thermally fully developed laminar rarefied gas flow in annular microducts is studied using slip flow boundary conditions. Two different cases of the thermal boundary conditions are considered, namely: uniform temperature at the outer wall and adiabatic inner wall (Case A) and uniform temperature at the inner wall and adiabatic outer wall (Case B). Using the previously obtained velocity distribution, energy conservation equation subjected to relevant boundary conditions is numerically solved using fourth order Runge-Kutta method. The Nusselt number values are presented in graphical form as well as tabular form. It is realized that for the case A increasing aspect ratio results in increasing the Nusselt number, while the opposite is true for the case B. The effect of aspect ratio on Nusselt number is more notable at smaller values of Knudsen number, while its effect becomes slighter at large Knudsen numbers. Also increasing Knudsen number leads to smaller values of Nusselt number for the both cases.

The Effect of Biot Number on a One-Dimensional General Conduction Solution

2021 ◽  
Author(s):  
Robert L. McMasters ◽  
Filippo de Monte ◽  
James V. Beck
Keyword(s):  
Boundary Condition ◽  
Analytical Solution ◽  
Boundary Conditions ◽  
Biot Number ◽  
Analytical Solutions ◽  
Heat Fluxes ◽  
Graphical Form ◽  
Large Temperature ◽  
Convection Coefficient ◽  
General Analytical Solution

Abstract Analytical solutions for thermal conduction problems are extremely important, particularly for verification of numerical codes. Temperatures and heat fluxes can be calculated very precisely, normally to eight or ten significant figures, even in situations involving large temperature gradients. It can be convenient to have a general analytical solution for a transient conduction problem in rectangular coordinates. The general solution is based on the principle that the three primary types of boundary conditions (prescribed temperature, prescribed heat flux, and convective) can all be handled using convective boundary conditions. A large convection coefficient closely approximates a prescribed temperature boundary condition and a very low convection coefficient closely approximates an insulated boundary condition. Since a dimensionless solution is used in this research, the effect of various values of dimensionless convection coefficients, or Biot number, are explored. An understandable concern with a general analytical solution is the effect of the choice of convection coefficients on the precision of the solution, since the primary motivation for using analytical solutions is the precision offered. An investigation is made in this study to determine the effects of the choices of large and small convection coefficients on the precision of the analytical solutions generated by the general convective formulation. Results are provided, in tablular and graphical form, to illustrate the effects of the choices of convection coefficients on the precision of the general analytical solution.

Implementation of partial slip boundary conditions in an open-source finite-volume-based computational library

2019 ◽  
Vol 39 (4) ◽  
pp. 377-387 ◽  
Author(s):  
Célio Fernandes ◽  
Luís Lima Ferrás ◽  
Florian Habla ◽  
Olga Sousa Carneiro ◽  
João Miguel Nóbrega
Keyword(s):  
Boundary Conditions ◽  
Open Source ◽  
Analytical Solutions ◽  
Plug Flow ◽  
Flow Distribution ◽  
Polymer Processing ◽  
Partial Slip ◽  
Slip Boundary Conditions ◽  
Slip Boundary ◽  
Extra Stress Tensor

Abstract This paper reports the implementation of slip boundary conditions in the open-source computational library OpenFOAM. The linear and nonlinear Navier slip laws, which are newly implemented in this paper, can be used both for Newtonian and viscoelastic constitutive models. For the former case, the Couette flow assumption near the wall is employed, and for the latter, the cell-centered extra-stress tensor components are linearly extrapolated to the wall. The validation is performed by comparing the numerical results obtained for Newtonian and simplified Phan-Thien-Tanner constitutive model fluids in Couette and Poiseuille flows, with existing analytical solutions. The results obtained using different slip factors were shown to be in agreement with the analytical solutions, even for the most extreme cases where the slip factor is high enough to induce a plug flow pattern for the velocity field. The newly implemented boundary conditions are also used to study the influence of slip in polymer processing, namely in the production of an extruded profile. The results obtained show that the developed slip boundary conditions are able to deal with complex geometrical problems, and are an important tool to support the search of a balanced flow distribution in the design of profile extrusion dies.

Sign in / Sign up

Export Citation Format

Share Document