scholarly journals Research into mechanical properties of an ablative composite on a polymer matrix base with aerogel particles

2021 ◽  
pp. 114855
Author(s):  
Robert Szczepaniak ◽  
Andrzej Komorek ◽  
Paweł Przybyłek ◽  
Aneta Krzyżak ◽  
Marek Roskowicz ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Polymer Matrix ◽  
Matrix Base

Effect of fibre content on the mechanical properties of hemp fibre woven fabrics/polypropylene composite laminates

2021 ◽  
pp. 096739112110239
Author(s):  
Sheedev Antony ◽  
Abel Cherouat ◽  
Guillaume Montay
Keyword(s):  
Mechanical Properties ◽  
Polymer Matrix ◽  
Composite Laminates ◽  
Volume Fraction ◽  
Fibre Volume Fraction ◽  
Fibre Volume ◽  
Woven Fabrics ◽  
Fibre Content ◽  
Viscoelastic Behaviour ◽  
Hemp Fibre

Nowadays natural fibre composites have gained great significance as reinforcements in polymer matrix composites. Composite material based on a polymer matrix reinforced with natural fibres is extensively used in industry due to their biodegradability, recyclability, low density and high specific properties. A study has been carried out here to investigate the fibre volume fraction effect of hemp fibre woven fabrics/PolyPropylene (PP) composite laminates on the tensile properties and impact hammer impact test. Initially, composite sheets were fabricated by the thermal-compression process with desired number of fabric layers to obtain composite laminates with different fibre volume fraction. Uniaxial, shear and biaxial tensile tests were performed and mechanical properties were calculated. Impact hammer test was also carried out to estimate the frequency and damping parameters of stratified composite plates. Scanning Electron Microscope (SEM) analysis was performed to observe the matrix and fibre constituent defects. Hemp fabrics/PP composite laminates exhibits viscoelastic behaviour and as the fibre volume fraction increases, the viscoelastic behaviour decreases to elastic behaviour. Due to this, the tensile strength increases as the fibre content increases. On the other hand, the natural frequency increases and damping ratio decrease as the fibre volume fraction increases.

Effects of the Mould Pressure and Mould Pressing Time on the Properties of Graphite/Phenolic Resin Composites

2013 ◽  
Vol 706-708 ◽  
pp. 95-98
Author(s):  
Mi Dan Li ◽  
Dong Mei Liu ◽  
Lu Lu Feng ◽  
Huan Niu ◽  
Yao Lu
Keyword(s):  
Mechanical Properties ◽  
Electrical Conductivity ◽  
Flexural Strength ◽  
Polymer Matrix ◽  
Phenolic Resin ◽  
Polymer Matrix Composites ◽  
Resin Composites ◽  
Matrix Composites ◽  
Natural Graphite ◽  
Pressing Time

Polymer matrix composites made from phenolic resin are filled with natural graphite powders. They are fabricated by compression molding technique. The density, electrical conductivity and flexural strength of composite are analyzed to determine the influences of mould pressure and mould pressing time on the physical, electrical and mechanical properties of composite. It is found that the density, electrical conductivity and flexural strength of composites increased with increasing mould pressure. Under pressure of 40 MPa for 60 min, the density, electrical conductivity and flexural strength of composites were 1.85 g/cm3, 4.35  103 S/cm and 70 MPa, respectively. The decreased gaps could be the main reason for the increasing of density, electrical conductivity and flexural strength as mould pressure increases. The results also show that the density of composites increased with increasing mould pressing time.

Morphology and Mechanical Properties of Poly(Lactic Acid) and Propylene-Ethylene Copolymer Blends: Effect of Organoclay Types

2017 ◽  
Vol 737 ◽  
pp. 269-274
Author(s):  
Sirirat Wacharawichanant ◽  
Chaninthon Ounyai ◽  
Ployvaree Rassamee
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Tensile Properties ◽  
Polymer Matrix ◽  
Poly Lactic Acid ◽  
Dispersed Phase ◽  
Copolymer Blends ◽  
Morphology Analysis ◽  
Ethylene Copolymer ◽  
Morphology And Mechanical Properties

The effects of four types of organoclay on morphology and mechanical properties of poly(lactic acid) (PLA)/propylene-ethylene copolymer (PEC) blends were investigated. The ratio of PLA and PEC was 80/20 by weight and the organoclay content was 5 phr. The morphology analysis showed that the addition of all oganocaly types could improve the miscibility of PLA and PEC blends due to the decreased of the domain sizes of PEC dispersed phase in the polymer matrix. The tensile properties showed Young’s modulus of the PLA/PEC blends was improved after adding clay treated surface with 25-30 wt% trimethyl stearyl ammonium.

scholarly journals Effect of Silane Functionalization on Properties of Poly(Lactic Acid)/Palygorskite Nanocomposites

Inorganics ◽  
2021 ◽  
Vol 9 (1) ◽  
pp. 3
Author(s):  
Anton Kasprzhitskii ◽  
Georgy Lazorenko ◽  
Alexander Kruglikov ◽  
Irina Kuchkina ◽  
Vadim Gorodov
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Polymer Matrix ◽  
Covalent Bond ◽  
Poly Lactic Acid ◽  
Hydroxyl Groups ◽  
Good Dispersion ◽  
Melt Compounding

Poly(lactic acid) (PLA)/palygorskite (Paly) nanocomposites were prepared using the melt compounding technique. Paly modified by 3-aminopropyltriethoxysilane (APTES) and vinyltrimethoxysilane (VTMS) was used as nanofiller for PLA with concentrations in the 1–7 wt% range. It has been found that the functionalization allows a covalent bond between the hydroxyl groups of the Paly and the PLA matrix, evidenced by the improvement in mechanical properties. Paly modification with VTMS has better properties compared with Pale modification with APTES. This indicates a better adhesion between the Paly-VTMS and PLA matrix, and a good dispersion of the nanofiller in the polymer matrix.

Synthesis and Characterizations of Poly(Butylene Succinate) Copolyester

2014 ◽  
Vol 1015 ◽  
pp. 381-384
Author(s):  
Li Liu ◽  
Li Hai Cai ◽  
Dan Liu ◽  
Jun Xu ◽  
Bao Hua Guo
Keyword(s):  
Mechanical Properties ◽  
Polymer Matrix ◽  
Crystallization Temperature ◽  
In Situ Polymerization ◽  
Nucleating Agent ◽  
Single Fiber ◽  
Butylene Succinate ◽  
Crystallization Behaviors ◽  
Polymerization Method

The poly (butylene succinate) (PBS) and 3 wt% attapulgite (ATP) reinforced PBS/ATP nanocomposites with 1,6-hexanediol were fabricated using an in situ polymerization method. The crystallization behaviors indicated that ATP had effectively acted as nucleating agent, resulting in the enhancement on the crystallization temperature. The SEM results showed a superior interfacial linkage between ATP and PBS. Also, ATP could disperse as a single fiber and embed in the polymer matrix, which resulted in the improved mechanical properties.

scholarly journals MICROSTRUCTURE RESEARCH OF THE UNIDIRECTIONAL ORGANOPLASTIC BASED ON RUSAR-NT ARAMID FIBERS AND EPOXY-POLYSULFONE BINDER

2020 ◽  
pp. 19-26
Author(s):  
E.N. Kablov ◽  
◽  
G.S. Kulagina ◽  
G.F. Zhelezina ◽  
S.L. Lonskii ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Material ◽  
Polymer Matrix ◽  
Packing Density ◽  
Tensile Tests ◽  
Polymer Composite Material ◽  
Aramid Fibers ◽  
Before And After ◽  
Binder Structure

This paper studies a polymer composite material - a unidirectional organoplastic based on Rusar-NT aramid fiber and a melt epoxy-polysulfone binder. Organoplastic has the following mechanical properties: tensile strength 2060 MPa, Young's modulus 101 GPa. The microstructure of the fiber and the polymer matrix in the organoplastic samples was studied before and after tensile tests. The features of the formation of the binder structure depending on the packing density of the fibers in organoplastics have been determined. The nature of the destruction of fibers and polymer matrix caused by the uniaxial tension has been studied.

Development of Some Promising Approaches for The Toughening of High-Temperature Polymers

1998 ◽  
Vol 519 ◽  
Author(s):  
C. Kumudinie ◽  
J. K. Premachandra ◽  
J. E. Mark ◽  
T. D. Dang ◽  
M. R. Unroe ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Optical Properties ◽  
Thermal Properties ◽  
High Temperature ◽  
Polymer Matrix ◽  
Hybrid Material ◽  
Arylene Ether ◽  
Rubbery Phase ◽  
Maximum Extensibility

AbstractHigh-temperature poly(arylene ether) and hydroxypolybenzoxazole polymers were toughened using dispersed rubbery phases. This rubbery phase was a hybrid material which was in-situ generated within the polymer matrix using mixtures of partially-hydrolyzable trialkoxy and dialkoxy organosilanes with a fully hydrolyzable tetraalkoxysilane. The resulting materials were characterized with regard to their structures, mechanical properties (modulus, ultimate strength, maximum extensibility, and toughness), thermal properties, optical properties, and tendencies to absorb water. Some of the results are presented here.

Sign in / Sign up

Export Citation Format

Share Document