Coupled effect of temperature and impact loading on tensile strength of ultra-high performance fibre reinforced concrete

2019 ◽  
Vol 229 ◽  
pp. 111432 ◽  
Author(s):  
Xiangwei Liang ◽  
Chengqing Wu ◽  
Yekai Yang ◽  
Cheng Wu ◽  
Zhongxian Li
Keyword(s):  
Tensile Strength ◽  
Reinforced Concrete ◽  
Impact Loading ◽  
High Performance ◽  
Effect Of Temperature ◽  
Fibre Reinforced Concrete ◽  
Coupled Effect ◽  
High Performance Fibre

scholarly journals Performance of ultra-high performance fibre reinforced concrete plates under impact loads

2021 ◽  
Author(s):  
Hesham Othman
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Fracture Energy ◽  
High Performance ◽  
Steel Reinforcement ◽  
Fibre Content ◽  
Fibre Reinforced Concrete ◽  
Concrete Plates ◽  
High Performance Fibre

The next generation of concrete, Ultra-High Performance Fibre Reinforced Concrete (UHP-FRC), exhibits exceptional mechanical characteristics. UHP-FRC has a compressive strength exceeding 150 MPa, tensile strength in the range of 8-12 MPa, and fracture energy of several orders of magnitudes of traditional concrete. The focus of this research is to investigate and analyze the advantage of using UHP - FRC in impact resistance structures. To achieve these goals, two experimental testing programs and major numerical investigations have been conducted. The material experimental investigation has been conducted to determine the effects of strain rate on UHP - FRC. Two parameters are investigated, namely: compressive strength (80, 110, 130, and 150 MPa); and steel fibre content (0, 1, 2, and 3%). Experimental results showed that the rate sensitivity decreases with the increase in the compressive strength ; and the dynamic enhancement of tensile strength is inversely proportional to the fibre content. The structural impact testing program focuses on the dynamic response of full - scale reinforced concrete plates as well as generating precise impact measurements. Twelve reinforced plates with identical dimensions are tested under high-mass low-velocity multi-impacts. The investigated parameters include: concrete type (NSC, HSC, and UHP - FRC), fibre volume content, and steel reinforcement ratio. The results showed that the use of UHP -FRC instead of NSC or HSC is able to change the failure mode from punching to pure flexural; and UHP -FRC containing 3% fibre has superior dynamic properties. For plates with identical steel reinforcement, the total impact energy of UHP-FRC plate containing 3% fibres is double the capacity of UHP - FRC plate containing 2% fibres , and 18 times the capacity of NSC plate. A three-dimensional finite element analysis has been performed using ABAQUS/Explicit to model multi-impacts on RC plates and the applicability is verified using existing experimental data. Concrete damage plasticity (CDP) model is adapted to define UHP - FRC. The CDP constitutive model parameters for the new material are calibrated through a series of parametric studies. Computed responses are sensitive to CDP parameters related to the tension, fracture energy, and expansion properties. The analytical results showed that the existing CDP model can predict the response and crack pattern of UHP - FRC reasonably well.

Behaviour of Different Types of Concrete under Impact and Quasi-Static Loading

2013 ◽  
Vol 486 ◽  
pp. 295-300 ◽  
Author(s):  
Petr Máca ◽  
Petr Konvalinka ◽  
Manfred Curbach
Keyword(s):  
Tensile Strength ◽  
Reinforced Concrete ◽  
Impact Loading ◽  
High Performance ◽  
High Performance Concrete ◽  
Fibre Reinforced Concrete ◽  
Static Conditions ◽  
Direct Tensile ◽  
Direct Tensile Strength ◽  
The Impact

This paper describes mixture formulation of Ultra High Performance Fibre Reinforced Concrete (UHPFRC) with 2% of fibres by volume and its response to quasi-static and dynamic impact loading. The UHPFRC mixture was prepared using locally available constituents and no special curing or mixing methods were used for its production. In addition, the mechanical parameters of three other types of concrete, i.e. normal strength concrete (NSC), fibre reinforced concrete (FRC) and high performance concrete (HPC) is compared. The main properties assessed throughout the experimental work are compressive, flexural and direct tensile strength as well as response of tested concretes to impact flexural loading. The impact loading is produced by a vertically falling weight of 24 kg from the height of 1 m on concrete prisms. The strain rate increase corresponds to low-velocity impacts such as vehicle crash or falling rocks. Compressive strength of UHPFRC exceeded 130 MPa and its direct tensile strength was 10.3 MPa. This type of concrete also exhibited strain hardening both in flexure under quasi-static conditions and during impact. Based on the comparison of impact reactions, it was concluded that the resistance of UHPFRC to impact loading is superior compared to the referent types of concretes (NSC, FRC, HPC).

Experimental procedure for determination of the energy dissipation capacity of ultra-high-performance fibre-reinforced concrete under localized impact loading

2019 ◽  
Vol 10 (2) ◽  
pp. 251-265 ◽  
Author(s):  
Petr Konrád ◽  
Radoslav Sovják
Keyword(s):  
Reinforced Concrete ◽  
Impact Loading ◽  
High Performance ◽  
Volume Fraction ◽  
Concrete Specimen ◽  
Basic Material ◽  
Fibre Reinforced Concrete ◽  
Significant Difference ◽  
The Impact ◽  
High Performance Fibre

Research presented in this article is aimed to investigate the ability of ultra-high-performance fibre-reinforced concrete to absorb and dissipate mechanical energy at elevated strain rate loading. Specimens made of ultra-high-performance fibre-reinforced concrete were subjected to the low-velocity impact using the new testing procedure where no fixed supports that hold the sample during the impact were applied. The fibre volume fraction of the ultra-high-performance fibre-reinforced concrete was set as the main test variable in the framework of this study and the volumetric fraction of fibres was ranging from 0.125% to 2%. A high-speed camera was used to measure velocities of the impactor and the ultra-high-performance fibre-reinforced concrete specimen before and after the impact. Consequently, the energy dissipated by the ultra-high-performance fibre-reinforced concrete specimen during the impact was calculated using a simple energy balance equation. To determine the basic material properties of ultra-high-performance fibre-reinforced concrete, quasi-static loading rate was applied and conventional methods were used. A significant difference between the values of dissipated energies for different loading rates and various fibre volumetric fractions was observed. It can be noted that the new procedure shows a reasonable approach for testing the fibre-reinforced cementitious composites under localized impact loading and is worthy of further optimization.

scholarly journals Performance of ultra-high performance fibre reinforced concrete plates under impact loads

2021 ◽  
Author(s):  
Hesham Othman
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Fracture Energy ◽  
High Performance ◽  
Steel Reinforcement ◽  
Fibre Content ◽  
Fibre Reinforced Concrete ◽  
Concrete Plates ◽  
High Performance Fibre

The next generation of concrete, Ultra-High Performance Fibre Reinforced Concrete (UHP-FRC), exhibits exceptional mechanical characteristics. UHP-FRC has a compressive strength exceeding 150 MPa, tensile strength in the range of 8-12 MPa, and fracture energy of several orders of magnitudes of traditional concrete. The focus of this research is to investigate and analyze the advantage of using UHP - FRC in impact resistance structures. To achieve these goals, two experimental testing programs and major numerical investigations have been conducted. The material experimental investigation has been conducted to determine the effects of strain rate on UHP - FRC. Two parameters are investigated, namely: compressive strength (80, 110, 130, and 150 MPa); and steel fibre content (0, 1, 2, and 3%). Experimental results showed that the rate sensitivity decreases with the increase in the compressive strength ; and the dynamic enhancement of tensile strength is inversely proportional to the fibre content. The structural impact testing program focuses on the dynamic response of full - scale reinforced concrete plates as well as generating precise impact measurements. Twelve reinforced plates with identical dimensions are tested under high-mass low-velocity multi-impacts. The investigated parameters include: concrete type (NSC, HSC, and UHP - FRC), fibre volume content, and steel reinforcement ratio. The results showed that the use of UHP -FRC instead of NSC or HSC is able to change the failure mode from punching to pure flexural; and UHP -FRC containing 3% fibre has superior dynamic properties. For plates with identical steel reinforcement, the total impact energy of UHP-FRC plate containing 3% fibres is double the capacity of UHP - FRC plate containing 2% fibres , and 18 times the capacity of NSC plate. A three-dimensional finite element analysis has been performed using ABAQUS/Explicit to model multi-impacts on RC plates and the applicability is verified using existing experimental data. Concrete damage plasticity (CDP) model is adapted to define UHP - FRC. The CDP constitutive model parameters for the new material are calibrated through a series of parametric studies. Computed responses are sensitive to CDP parameters related to the tension, fracture energy, and expansion properties. The analytical results showed that the existing CDP model can predict the response and crack pattern of UHP - FRC reasonably well.

scholarly journals Behaviour of UHPFRCs in compression under high stress-rates

2018 ◽  
Vol 183 ◽  
pp. 02005
Author(s):  
Ezio Cadoni ◽  
Matteo Dotta ◽  
Daniele Forni
Keyword(s):  
Reinforced Concrete ◽  
Mechanical Behaviour ◽  
High Performance ◽  
High Stress ◽  
Slight Reduction ◽  
Fibre Reinforcement ◽  
Fibre Reinforced Concrete ◽  
Dynamic Event ◽  
The Matrix ◽  
High Performance Fibre

The paper presents the results obtained on cylindrical Ultra High Performance Fibre Reinforced Concrete specimens with diameter of 30mm and a height of 60mm under compression at high stress rate (1.7–2.3 TPa/s). Four different percentages of fibre reinforcement are considered (1, 2, 3, and 4% fibre content) and compared with the results of the matrix (UHPC). A slight reduction of the strength and fracture time with the introduction of fibres is observed. The experimental results are analysed and discussed with the intent to better understand the mechanical behaviour of UHPFRC materials in case of dynamic event under service loading conditions.

Sign in / Sign up

Export Citation Format

Share Document