Prediction of the tensile strength of hybrid polymer composites filled with spherical particles and short fibers

2018 ◽  
Vol 187 ◽  
pp. 509-517 ◽  
Author(s):  
Hong-Liang Dai ◽  
Zheng-Wei Huang ◽  
Chao Mei ◽  
Zhong-Yan Lin
Keyword(s):  
Tensile Strength ◽  
Polymer Composites ◽  
Spherical Particles ◽  
Hybrid Polymer ◽  
Short Fibers

Prediction of the tensile strength of polymer composites filled with aligned short fibers

2019 ◽  
Vol 38 (14) ◽  
pp. 658-668 ◽  
Author(s):  
Yang Yang ◽  
Jian Pang ◽  
Hong-Liang Dai ◽  
Xiao-Min Xu ◽  
Xing-Quan Li ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Polymer Composites ◽  
Short Fibers

Effect of quasi-static and intermediate strain rates on the tensile properties of hybrid polymer composites

2021 ◽  
pp. 095440622110288
Author(s):  
Fatih Balikoglu ◽  
Tayfur K Demircioglu ◽  
Ege A Diler ◽  
Akın Ataş
Keyword(s):  
Tensile Strength ◽  
Strain Rate ◽  
Polymer Composites ◽  
Hybrid Composites ◽  
Uniaxial Tensile ◽  
Tensile Behaviour ◽  
Strain Rates ◽  
Hybrid Polymer ◽  
Hybrid Laminates ◽  
Intermediate Strain Rates

This study presents the results of an investigation on the tensile behaviour of hybrid polymer composites under different strain rates. Glass/carbon, aramid/carbon, glass/aramid, and glass/aramid/carbon hybrid laminates were produced using vacuum assisted resin transfer molding method with epoxy resin system. Uniaxial tensile testing was performed to determine the tensile strength, modulus and failure strain of the hybrid laminates under quasi static (0.001 s‒1) and intermediate (5 and 10 s‒1) strain rates. Tensile strength and elastic modulus of hybrid composites increased with increasing the strain rate. Hybrid laminates with glass fibre were more sensitive to the strain rate. Carbon layers located at the centre of the hybrid laminates resulted in increased tensile strength, indicating the major role of stacking sequence on the behaviour of hybrid composites. Scanning electron microscope (SEM) was used to examine the fracture surfaces of the laminates. The extent of damage propagation was significantly broader at intermediate strain rates.

Hybrid polymer composite materials. Part 2. Preparation technology

2020 ◽  
pp. 8-13
Keyword(s):  
Composite Materials ◽  
Impact Toughness ◽  
Polymer Composites ◽  
The Other ◽  
Polymer Materials ◽  
Hybrid Polymer ◽  
Preparation Technology ◽  
Advantages And Disadvantages ◽  
Hybrid Polymer Composite ◽  
The One

The main methods (pressing and winding) of the processing of hybrid polymer composites to obtain items were examined. Advantages and disadvantages of the methods were noted. Good combinations of different-module fibers (carbon, glass, boron, organic) in hybrid polymer materials are described, which allow one to prepare materials with high compression strength on the one hand, and to increase fracture energy of samples and impact toughness on the other hand.

scholarly journals Tunable Crystalline Phases in UV-Curable PEG-Grafted Ladder-Structured Silsesquioxane/Polyimide Composites

Materials ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2295 ◽  
Author(s):  
Ryung Il Kim ◽  
Ju Ho Shin ◽  
Jong Suk Lee ◽  
Jung-Hyun Lee ◽  
Albert S. Lee ◽  
...  
Keyword(s):  
Polymer Composites ◽  
Surface Properties ◽  
Weight Ratio ◽  
Hybrid Polymer ◽  
Water Contact ◽  
Uv Curable ◽  
Wide Range ◽  
Drastic Increase ◽  
Polyimide Composites ◽  
Crystalline Polyethylene

A series of UV-curable hybrid composite blends containing a carboxylic acid functionalized polyimidewith varying amounts of high molecular weight (~1 K) PEG-grafted ladder-structured polysilsesquioxanes copolymerized with methacryl groups were fabricated and their structural, thermal, mechanical, and surface properties characterized. At a composite weight ratio of polyimide above 50 wt.%, a stark shift from amorphous to crystalline polyethylene glycol (PEG) phases were observed, accompanied by a drastic increase in both surface moduli and brittleness index. Moreover, fabricated composites were shown to have a wide range water contact angle, 9.8°–73.8°, attesting to the tunable surface properties of these amphiphilic hybrid polymer composites. The enhanced mechanical properties, combined with the utility of tunable surface hydrophilicity allows for the possible use of these hybrid polymer composites to be utilized as photosensitive polyimide negative photoresists for a myriad of semiconductor patterning processes.

Influence of the Composition of Cement Mortars Modified by Lime or Polymers on the Mechanical Properties and Microstructure of Mortars

2013 ◽  
Vol 592-593 ◽  
pp. 647-650 ◽  
Author(s):  
Małgorzata Lenart
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Reinforced Concrete ◽  
Flexural Strength ◽  
Polyvinyl Alcohol ◽  
Polymer Composites ◽  
Adhesion Strength ◽  
Hardened Cement ◽  
Cement Mortars ◽  
Styrene Butadiene

Cement – polymer composites are nowadays widely used in repair systems not only in case of concrete or reinforced concrete constructions but also in masonry. Polymers addition for example already at 5% m.c. modifies the structure of the cement – polymer composite in a way that many of the mechanical properties such as flexural strength, tensile strength or adhesion to substrates are improved. The paper presents the results of tests such as flexural, compressive or adhesion strength to ceramic substrate of hardened cement mortars with different composition, as well as selected cement mortars modified by two polymers: polyvinyl alcohol and styrene – butadiene polymer dosed at 5 % m.c. Four types of cement mortars modified by lime (component used in historical constructions as well as in contemporary masonry mortars) are also examined for comparison.

Effect of Li on Mechanical Properties and Electrical Conductivity of the Al–Zn–Cu–Mg Based Alloys

2021 ◽  
Vol 21 (9) ◽  
pp. 4897-4901
Author(s):  
Hyo-Sang Yoo ◽  
Yong-Ho Kim ◽  
Hyeon-Taek Son
Keyword(s):  
Mechanical Properties ◽  
Electrical Conductivity ◽  
Grain Size ◽  
Tensile Strength ◽  
Spherical Particles ◽  
Al Alloy ◽  
High Angle ◽  
Average Grain Size ◽  
Strength Improvement ◽  
Li Content

In this study, changes in the microstructure, mechanical properties, and electrical conductivity of cast and extruded Al–Zn–Cu–Mg based alloys with the addition of Li (0, 0.5 and 1.0 wt.%) were investigated. The Al–Zn–Cu–Mg–xLi alloys were cast and homogenized at 570 °C for 4 hours. The billets were hot extruded into rod that were 12 mm in diameter with a reduction ratio of 38:1 at 550 °C. As the amount of Li added increased from 0 to 1.0 wt.%, the average grain size of the extruded Al alloy increased from 259.2 to 383.0 µm, and the high-angle grain boundaries (HGBs) fraction decreased from 64.0 to 52.1%. As the Li content increased from 0 to 1.0 wt.%, the elongation was not significantly different from 27.8 to 27.4% and the ultimate tensile strength (UTS) was improved from 146.7 to 160.6 MPa. As Li was added, spherical particles bonded to each other, forming an irregular particles. It is thought that these irregular particles contribute to the strength improvement.

The influence of functionalization time of carbon nanotube on the mechanical properties of the epoxy composites

2017 ◽  
Vol 51 (12) ◽  
pp. 1693-1701 ◽  
Author(s):  
EA Zakharychev ◽  
EN Razov ◽  
Yu D Semchikov ◽  
NS Zakharycheva ◽  
MA Kabina
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Carbon Nanotube ◽  
Composite Materials ◽  
Polymer Composites ◽  
Epoxy Composites ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

This paper investigates the structure, length, and percentage of functional groups of multi-walled carbon nanotubes (CNT) depending on the time taken for functionalization in HNO3 and H2SO4 mixture. The carbon nanotube content and influence of functionalization time on mechanical properties of polymer composite materials based on epoxy matrix are studied. The extreme dependencies of mechanical properties of carbon nanotube functionalization time of polymer composites were established. The rise in tensile strength of obtained composites reaches 102% and elastic modulus reaches 227% as compared to that of unfilled polymer. The composites exhibited best mechanical properties by including carbon nanotube with 0.5 h functionalization time.

Bulk and nano-mechanical behavior of silver and silver-CNT-reinforced hybrid polymer composites

2015 ◽  
Vol 37 (8) ◽  
pp. 2581-2587 ◽  
Author(s):  
Himel Chakraborty ◽  
Dipa Ray ◽  
Partha Protim Chattopadhyay
Keyword(s):  
Mechanical Behavior ◽  
Polymer Composites ◽  
Hybrid Polymer

Post-Fatigue Creep and Stress Relaxation Response of a Hybrid Polymer Composite

2017 ◽  
Author(s):  
Raghu V. Prakash ◽  
Monalisha Maharana
Keyword(s):  
Stress Relaxation ◽  
Polymer Composites ◽  
Polymer Composite ◽  
Fatigue Loading ◽  
Synthetic Fiber ◽  
Relaxation Response ◽  
Hybrid Polymer ◽  
Fatigue Cycling ◽  
Creep And Stress Relaxation ◽  
Hybrid Polymer Composite

Polymer composites have a characteristic, composition specific visco-elastic property which influences the damage progression during fatigue cycling. While some researchers have studied the time dependent constitutive response of polymer composites during the first cycle of fatigue loading, very few have experimentally investigated the dependence of visco-elastic response of built-up polymer composite materials at various stages of fatigue cycling [1]. Our earlier studies on fatigue response of polymer composites focused primarily on the stiffness degradation as a function of applied cycles of loading, which represents the gross response of the material [2]. While doing such an experiment, complimentary experimental techniques to measure the temperature evolution was attempted through the use of infrared thermal imaging technique, which gave some insight into the change in temperature response as a function of fatigue cycling. However, there was no systematic measurement of creep and stress relaxation response of the composite material as a function of induced fatigue damage. The present paper describes the results of creep and stress-relaxation obtained during uni-axial fatigue loading of a hybrid polymer composite material. For this purpose, a woven carbon fiber mat was chosen as the synthetic fiber and Flax fiber in the unidirectional form was chosen as the natural fiber that is laid between the two layers of woven carbon fiber mat. Epoxy LY 556 and hardener Araldite® was used for building up of composite laminate by hand-lay-up technique. Dog-bone shaped tensile specimens with a gage width of 13 mm and gage length of 57 mm were extracted from the 250 × 250 mm sq. plate laminate of 2.1 mm thickness using a numerical controlled milling machine. The specimens were tested at 35% of their median tensile strengths under fatigue at a positive stress ratio (Pmin/Pmax) of 0.1 in tension-tension loading. Prior to start of fatigue loading, the specimens were held in load control and the strain in the gage length was measured for understanding the creep response over 2500 seconds. For stress-relaxation characterization, the specimens were held in extensometer control over a period of 2500 sec. The creep and stress relaxation tests were carried out after periodic intervals of fatigue cycling. It was observed that in the case of un-impacted specimens, the creep rate is consistent with the stiffness variation, which in turn, is dependent on the number of fatigue cycles - till it showed signs of de-lamination. Thereafter it was governed by the woven synthetic fiber response. Similarly, the stress relaxation response was found to decrease with increasing fatigue cycles. In case of impacted specimens, the local deformation had a prominent role in terms of creep and stress relaxation response.

Sign in / Sign up

Export Citation Format

Share Document