Three-dimensional progressive failure modeling of glass fiber reinforced thermoplastic composites for impact simulation

2017 ◽  
Vol 176 ◽  
pp. 757-767 ◽  
Author(s):  
Do-Hyoung Kim ◽  
Ku-Hyun Jung ◽  
In-Gyu Lee ◽  
Hee-June Kim ◽  
Hak-Sung Kim
Keyword(s):  
Glass Fiber ◽  
Progressive Failure ◽  
Three Dimensional ◽  
Thermoplastic Composites ◽  
Fiber Reinforced ◽  
Impact Simulation ◽  
Failure Modeling ◽  
Glass Fiber Reinforced

Elastic properties of injection molded short glass fiber reinforced thermoplastic composites

2020 ◽  
Vol 254 ◽  
pp. 112850
Author(s):  
Yucheng Zhong ◽  
Ping Liu ◽  
Qingxiang Pei ◽  
Viacheslav Sorkin ◽  
Athanasius Louis Commillus ◽  
...  
Keyword(s):  
Glass Fiber ◽  
Elastic Properties ◽  
Thermoplastic Composites ◽  
Fiber Reinforced ◽  
Short Glass Fiber ◽  
Glass Fiber Reinforced ◽  
Injection Molded ◽  
Short Glass

CO2-laser-assisted processing of glass fiber-reinforced thermoplastic composites

2013 ◽  
Author(s):  
Christian Brecher ◽  
Michael Emonts ◽  
Richard Ludwig Schares ◽  
Joffrey Stimpfl
Keyword(s):  
Glass Fiber ◽  
Co2 Laser ◽  
Thermoplastic Composites ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced

On the mechanical properties of continuous fiber reinforced thermoplastic composites realized through vacuum infusion

2020 ◽  
Vol 54 (27) ◽  
pp. 4231-4239
Author(s):  
Vishal Gavande ◽  
Anoop Anand
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Catalyst Concentration ◽  
Low Velocity Impact ◽  
Thermoplastic Composites ◽  
Fiber Reinforced ◽  
Low Velocity ◽  
Continuous Glass ◽  
Continuous Glass Fiber ◽  
Glass Fiber Reinforced

Continuous glass fiber reinforced thermoplastic composites have been manufactured and their mechanical properties have been evaluated. A catalyzed monomer is infused through a stack of compacted dry reinforcement under vacuum. The monomer undergoes radical polymerization with a peroxide catalyst. Viscosity and reactivity profile have been characterized to determine the catalyst concentration and temperature of infusion. Glass fiber reinforced thermoplastic composites realized through this method have mechanical properties that are comparable with that of epoxy with an added advantage of excellent toughness and repairability. For example, the residual compressive strength of thermoplastic composites after low-velocity impact is found to be over 140% more than that of epoxy-based composites using the same reinforcement and realized under identical manufacturing methods.

scholarly journals Thermoplastic Reaction Injection Pultrusion for Continuous Glass Fiber-Reinforced Polyamide-6 Composites

Materials ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 463 ◽  
Author(s):  
Ke Chen ◽  
Mingyin Jia ◽  
Hua Sun ◽  
Ping Xue
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
High Speed ◽  
Flexural Modulus ◽  
Polyamide 6 ◽  
Thermoplastic Composites ◽  
Fiber Reinforced ◽  
Pultrusion Process ◽  
Glass Fiber Reinforced ◽  
Pultruded Composites

In this paper, glass fiber-reinforced polyamide-6 (PA-6) composites with up to 70 wt% fiber contents were successfully manufactured using a pultrusion process, utilizing the anionic polymerization of caprolactam (a monomer of PA-6). A novel thermoplastic reaction injection pultrusion test line was developed with a specifically designed injection chamber to achieve complete impregnation of fiber bundles and high speed pultrusion. Process parameters like temperature of injection chamber, temperature of pultrusion die, and pultrusion speed were studied and optimized. The effects of die temperature on the crystallinity, melting point, and mechanical properties of the pultruded composites were also evaluated. The pultruded composites exhibited the highest flexural strength and flexural modulus, reaching 1061 MPa and 38,384 MPa, respectively. Then, effects of fiber contents on the density, heat distortion temperature, and mechanical properties of the composites were analyzed. The scanning electron microscope analysis showed the great interfacial adhesion between fibers and matrix at 180 °C, which greatly improved the mechanical properties of the composites. The thermoplastic reaction injection pultrusion in this paper provided an alternative for the preparation of thermoplastic composites with high fiber content.

scholarly journals Long Chopped Glass Fiber Reinforced Low-Density Unsaturated Polyester Resin under Different Initiation

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7307
Author(s):  
Xinjun Fu ◽  
Xiaojun Wang ◽  
Jinjian Zhu ◽  
Minzhuang Chen
Keyword(s):  
Glass Fiber ◽  
Polyester Resin ◽  
Unsaturated Polyester ◽  
Three Dimensional ◽  
Unsaturated Polyester Resin ◽  
Curing Temperature ◽  
Low Density ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced ◽  
Composite Samples

Long chopped glass fiber reinforced low-density unsaturated polyester resin (LCGFR-LDUPR) composite materials with light weight and excellent mechanical properties were prepared. It was proved that long chopped glass fiber, which was in length of 15.0 mm and chopped from ER4800-T718 plied yarn, was suitable for the preparation of LCGFR-LDUPR composite samples. With the coexistence of 1.50 parts per hundred of resin (phr) of methyl ethyl ketone peroxide (MEKP-II) and 0.05 phr of cobalt naphthenate, optimal preparation parameters were obtained, which were 20.00 phr of long chopped glass fiber, 2.50 phr of NH4HCO3, at a curing temperature of 58.0 °C. The lowest dosage of activated radicals produced by MEKP-II and cobalt naphthenate enabled the lower curing exothermic enthalpy and the slowest crosslinking for unsaturated polyester resin to carry out, resulting in a higher curing degree of resin. It was conducive to the formation, diffusion, and distribution of bubbles in uniform size, and also for the constitution of ideal three-dimensional framework of long glass fibers in the cured sample, which resulted in the LCGFR-LDUPR composite sample presenting the apparent density (ρ) of 0.68 ± 0.02 g/cm3, the compression strength (P) of 35.36 ± 0.38 MPa, and the highest specific compressive strength (Ps) of 52.00 ± 0.74 MPa/g·cm3. The work carried out an ideal three-dimensional framework of long chopped glass fiber in the reinforcement to low-density unsaturated polyester resin composite samples. It also presented the proper initiator/accelerator system of the lower curing exothermic enthalpy and the slowest crosslinking for unsaturated polyester resin.

scholarly journals The Effects of Strain Rates on Mechanical Properties and Failure Behavior of Long Glass Fiber Reinforced Thermoplastic Composites

Polymers ◽  
2019 ◽  
Vol 11 (12) ◽  
pp. 2019 ◽  
Author(s):  
Junjia Cui ◽  
Shaoluo Wang ◽  
Shuhao Wang ◽  
Guangyao Li ◽  
Peilin Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Ultimate Strength ◽  
Fracture Strain ◽  
Thermoplastic Composites ◽  
Strain Rates ◽  
Fiber Breakage ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced ◽  
Long Glass Fiber

Long glass fiber reinforced thermoplastic composites have been increasingly used in automotive parts due to their excellent mechanical properties and recyclability. However, the effects of strain rates on the mechanical properties and failure mechanisms of long glass fiber reinforced polypropylene composites (LGFRPPs) have not been studied systematically. In this study, the effects of strain rates (from 0.001 s−1 to 400 s−1) on the mechanical properties and failure mechanism of LGFRPPs were investigated. The results showed that ultimate strength and fracture strain of the LGFRPPs increased obviously, whereas the stiffness remained essentially unchanged with the strain rates from low to high. The micro-failure modes mainly consisted of fibers pulled out, fiber breakage, interfacial debonding, matrix cracking, and ductile to brittle (ductile pulling of fibrils/micro-fibrils) fracture behavior of the matrix. As the strain rates increased, the interfacial bonding properties of LGFRPPs increased, resulting in a gradual increase of fiber breakage at the fracture surface of the specimen and the gradual decrease of pull-out. In this process, more failure energy was absorbed, thus, the ultimate strength and fracture strain of LGFRPPs were improved.

Study on the Tensile Properties of Glass Fiber Reinforced Poly Cyclic Butylene Terephthalate Composites under and after High Temperature

2015 ◽  
Vol 727-728 ◽  
pp. 262-265
Author(s):  
Lu Zhang ◽  
Zhen Qing Wang ◽  
Ji Feng Zhang ◽  
Li Min Zhou
Keyword(s):  
High Temperature ◽  
Glass Fiber ◽  
Tensile Properties ◽  
Composite Laminates ◽  
Thermoplastic Composites ◽  
Fiber Reinforced ◽  
Melt Viscosity ◽  
Butylene Terephthalate ◽  
Glass Fiber Reinforced ◽  
Cyclic Butylene Terephthalate

A fatal disadvantage of continuously reinforced thermoplastic composites is the high melt viscosity of the matrix which hampers impregnation. However, the melt viscosity of low molecular weight cyclic butylene terephthalate resin can reach extremely low value, which simplifies impregnation and even allows for the use of thermoset production techniques resin transfer moulding. To solve the problem of the glass fiber reinforced poly cyclic butylene terephthalate composites applied in the environment of high temperature, the specimens of composite laminates were tested under and after different temperature. It has been observed that the tensile properties of GF/PCBT composites decrease with increasing temperature between room 25°C and 150°C and tend towards stability after the high temperature.

Sign in / Sign up

Export Citation Format

Share Document