Fatigue bearing failure of CFRP composite in biaxially loaded bolted joints at elevated temperature

2015 ◽  
Vol 127 ◽  
pp. 298-307 ◽  
Author(s):  
Zlatan Kapidžić ◽  
Hans Ansell ◽  
Joakim Schön ◽  
Kjell Simonsson
Keyword(s):  
Elevated Temperature ◽  
Bolted Joints ◽  
Bearing Failure ◽  
Cfrp Composite

Quasi-static bearing failure of CFRP composite in biaxially loaded bolted joints

2015 ◽  
Vol 125 ◽  
pp. 60-71 ◽  
Author(s):  
Zlatan Kapidžić ◽  
Hans Ansell ◽  
Joakim Schön ◽  
Kjell Simonsson
Keyword(s):  
Bolted Joints ◽  
Bearing Failure ◽  
Cfrp Composite

Strength Prediction of Double-Lap Bolted Joints of Woven Fabric CFRP Composite Plates Using Hashin Formulations

2015 ◽  
Vol 802 ◽  
pp. 290-294
Author(s):  
Hilton Ahmad ◽  
Mustafa Abbas Abed
Keyword(s):  
Failure Modes ◽  
Composite Plates ◽  
Bolted Joints ◽  
Woven Fabric ◽  
Strength Prediction ◽  
Bearing Failure ◽  
Bolted Joint ◽  
Element Analysis ◽  
Bearing Failures ◽  
Cfrp Composite

Failure modes in composite plates with bolted joint configuration include net-tension, shear-out and bearing failures. Few analytical and numerical approaches in strength prediction frameworks of composite plates with bolted joints were reported in the literatures. Present works are dealing with strength prediction in bearing failure of woven fabric CFRP plates with double lap bolted joint configurations by modeling 3D finite element analysis framework. The pre-processing stage is modeled using commercial ABAQUS CAE package and takes into account all parts interactions, clamping pressure and friction contact. Testing series are following the experimental works found from the literatures with variation of plate width to hole diameter (W/d) ratios and incorporated with finger-tight clamp-up. Hashin failure criterion was implemented as constitutive modeling in current analysis, based on ply-by-ply approaches found to be more appropriate phenomenon in bearing failure. The strength prediction results demonstrated good agreement with all experimental datasets particularly with bearing failures as compared with previously reported work, used stress concentration approach found to be accurate in net-tension failure only.

On-site monitoring of bearing failure in composite bolted joints using built-in eddy current sensing film

2020 ◽  
pp. 002199832097973
Author(s):  
Qijian Liu ◽  
Hu Sun ◽  
Yuan Chai ◽  
Jianjian Zhu ◽  
Tao Wang ◽  
...  
Keyword(s):  
Numerical Simulations ◽  
Eddy Current ◽  
Failure Modes ◽  
Bolted Joints ◽  
Bearing Failure ◽  
Monitoring Method ◽  
Current Sensing ◽  
Site Monitoring ◽  
Array Sensing ◽  
Bearing Damage

Bearing damage is one of the common failure modes in composite bolted joints. This paper describes the development of an on-site monitoring method based on eddy current (EC) sensing film to monitor the bearing damage in carbon fiber reinforced plastic (CFRP) single-lap bolted joints under tensile testing. Configuration design and operating principles of EC array sensing film are demonstrated. A series of numerical simulations are conducted to analyze the variation of EC when the bearing failure occurs around the bolt hole. The results of damage detection in the horizontal direction and through the thickness direction in the bolt hole with different exciting current directions are presented by the finite element method (FEM). Experiments are performed to prove the feasibility of the proposed EC array sensing film when the bearing failure occurs in CFRP single-lap bolted joints. The results of numerical simulations and experiments indicate that bearing failure can be detected according to the variation of EC in the test specimen.

Effect of Temperature Variation on Clamp Load of Bolted Joints

2014 ◽  
Vol 633-634 ◽  
pp. 1179-1186
Author(s):  
Shi Yuan Hou ◽  
Ri Dong Liao ◽  
Zheng Kun Cheng
Keyword(s):  
Mathematical Model ◽  
Elevated Temperature ◽  
Temperature Variation ◽  
Creep Behavior ◽  
Bolted Joints ◽  
Effect Of Temperature ◽  
Bolted Joint ◽  
One Dimensional ◽  
Nonlinear Variation ◽  
Relevant Factors

Considering the elastic-plastic and creep behavior of the material of bolted joint, and the nonlinear variation of its properties with temperature, this paper proposed a one-dimensional mathematical model for predicting clamp load variation with cyclic elevated-temperature. Then, relevant factors which may affect the process are studied, and some measures to enhance the threaded fitting reliability are proposed.

Sign in / Sign up

Export Citation Format

Share Document