scholarly journals Validation of low velocity impact modelling on different stacking sequences of CFRP laminates and influence of fibre failure

2013 ◽  
Vol 106 ◽  
pp. 549-559 ◽  
Author(s):  
N. Hongkarnjanakul ◽  
C. Bouvet ◽  
S. Rivallant
Keyword(s):  
Low Velocity Impact ◽  
Low Velocity ◽  
Velocity Impact ◽  
Fibre Failure ◽  
Cfrp Laminates ◽  
Impact Modelling

scholarly journals Experimental and Numerical Study of Low-Velocity Impact and Tensile after Impact for CFRP Laminates Single-Lap Joints Adhesively Bonded Structure

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 1016
Author(s):  
Chunxing Hu ◽  
Guibin Huang ◽  
Cheng Li
Keyword(s):  
Lap Joints ◽  
Low Velocity Impact ◽  
Adhesively Bonded ◽  
Low Velocity ◽  
Adhesive Film ◽  
Velocity Impact ◽  
Cfrp Laminates ◽  
Single Lap Joints ◽  
Impact Energies ◽  
The Impact

To investigate the mechanical behavior of the single-lap joints (SLJs) adhesively bonded structure of carbon fiber reinforced polymer (CFRP) laminates under the low-velocity impact (LVI) and tensile-after impact (TAI), tests and simulations were carried out. A finite element model (FEM) was established based on the cohesive zone model (CZM) and Hashin criterion to predict the damage evolution process of adhesive film, intra- and inter-laminar of the SLJs of CFRP laminates, and its effectiveness was verified by experiments. Moreover, three different overlap lengths (20 mm, 30 mm, and 40 mm) and four different impact energies (Intact joint, 10 J, 20 J, and 30 J) are considered in the present study. Finally, the effects of different impact energies and overlap lengths on the residual strength of SLJs after impact were discussed. The results divulged that numerical results of impact and TAI processes of SLJs were in good agreement with experiment results. During the impact process, the damage of the laminates was primarily fiber and matrix tensile damage, whereas the adhesive film was damaged cohesively; the areas of damage increased with the increase of impact energy, and the normal stress of the adhesive film expanded from the edge to the middle region with the increase of impact force. The influence of LVI on SLJs adhesively bonded structures was very significant, and it is not effective to obtain a higher impact resistance by increasing the overlap length. For the tensile process, the failure mode of TAI of the SLJs was interface failure, the surplus strength of the SLJs gradually decreased with the increase of the impact energy because of the smaller overlap length, the overlap length more than 30 mm, and the low energy impact has almost no effect on the residual strength of the SLJs.

scholarly journals Permanent indentation characterization for low-velocity impact modelling using three-point bending test

2013 ◽  
Vol 48 (20) ◽  
pp. 2441-2454 ◽  
Author(s):  
Natthawat Hongkarnjanakul ◽  
Samuel Rivallant ◽  
Christophe Bouvet ◽  
Arturo Miranda
Keyword(s):  
Low Velocity Impact ◽  
Bending Test ◽  
Low Velocity ◽  
Velocity Impact ◽  
Three Point Bending ◽  
Impact Modelling

scholarly journals Load and Strain Histories for CFRP Laminates under Low-Velocity Impact

1992 ◽  
Vol 35 (2) ◽  
pp. 159-164
Author(s):  
Joong-Suk KOOK ◽  
Masayuki SUZUKI ◽  
Tadaharu ADACHI ◽  
Sadayuki UJIHASHI ◽  
Hiroyuki MATSUMOTO
Keyword(s):  
Low Velocity Impact ◽  
Low Velocity ◽  
Velocity Impact ◽  
Cfrp Laminates

scholarly journals Load and strain histories for CFRP laminates under low-velocity impact.

1990 ◽  
Vol 56 (532) ◽  
pp. 2520-2525
Author(s):  
Joong Suk KOOK ◽  
Masayuki SUZUKI ◽  
Tadaharu ADACHI ◽  
Sadayuki UJIHASHI ◽  
Hiroyuki MATSUMOTO
Keyword(s):  
Low Velocity Impact ◽  
Low Velocity ◽  
Velocity Impact ◽  
Cfrp Laminates
Sign in / Sign up

Export Citation Format

Share Document