Laser induced graphene for in-situ ballistic impact damage and delamination detection in aramid fiber reinforced composites

2021 ◽  
Vol 202 ◽  
pp. 108551
Author(s):  
Kelsey Steinke ◽  
LoriAnne Groo ◽  
Henry A. Sodano
Keyword(s):  
Impact Damage ◽  
Ballistic Impact ◽  
Aramid Fiber ◽  
Fiber Reinforced Composites ◽  
Reinforced Composites ◽  
Fiber Reinforced ◽  
Delamination Detection

Sulfone-functionalized poly(p-phenylene terephthalamide) copolymer fibers with improved interfacial adhesion to epoxy matrices

2021 ◽  
pp. 095400832110089
Author(s):  
Ting Li ◽  
Zengxiao Wang ◽  
Hao Zhang ◽  
Yutong Cao ◽  
Zuming Hu ◽  
...  
Keyword(s):  
Interfacial Adhesion ◽  
Interfacial Shear Strength ◽  
Aramid Fiber ◽  
Fiber Reinforced Composites ◽  
Epoxy Composites ◽  
Reinforced Composites ◽  
Fiber Reinforced ◽  
Regular Arrangement ◽  
Epoxy Matrices ◽  
Polymerization Conditions

The poor interfacial adhesion of aramid fiber and matrix limits the application of the final composites. In this study, a series of the sulfone-functionalized poly( p-phenylene terephthalamide) (SPPTA) copolymers were satisfactorily synthesized and the effects of polymerization conditions (contents of the additional monomer and the cosolvent LiCl, molar concentration and ratio of the monomer, reaction temperature and time) on the molecular weight of the copolymer were discussed. The introduction of the sulfone group in aromatic polyamides not only increased the polarity of poly( p-phenylene terephthalamide) (PPTA) but destroyed the regular arrangement of the molecular chains, which greatly improved the surface free energy and the solubility of the polymers in organic solvents. The polymer maintained excellent thermal and interfacial properties. Compared with the PPTA fiber/epoxy composites, the interfacial shear strength (IFSS) of SPPTA fiber-reinforced epoxy composites reached 43.5 MPa, with a significantly enhancement of 20.8%, implying that the study provided an effective method to achieve highly interfacial adhesion of aramid fiber-reinforced composites.

Water-resistant hemp fiber-reinforced composites: In-situ surface protection by polyethylene film

2018 ◽  
Vol 112 ◽  
pp. 210-216 ◽  
Author(s):  
Yingji Wu ◽  
Changlei Xia ◽  
Liping Cai ◽  
Sheldon Q. Shi ◽  
Jiangtao Cheng
Keyword(s):  
Fiber Reinforced Composites ◽  
Polyethylene Film ◽  
Reinforced Composites ◽  
Fiber Reinforced ◽  
Hemp Fiber ◽  
Surface Protection

scholarly journals Effect of Temperature and Water Absorption on Low-Velocity Impact Damage of Composites with Multi-Layer Structured Flax Fiber

Materials ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 453 ◽  
Author(s):  
Yiou Shen ◽  
Junjie Zhong ◽  
Shenming Cai ◽  
Hao Ma ◽  
Zehua Qu ◽  
...  
Keyword(s):  
Water Absorption ◽  
Structural Damage ◽  
Impact Damage ◽  
Damage Threshold ◽  
Flax Fiber ◽  
Fiber Reinforced Composites ◽  
Reinforced Composites ◽  
Fiber Reinforced ◽  
Damage Resistance ◽  
The Impact

Temperature and moisture can cause degradation to the impact properties of plant fiber-based composites owing to their complex chemical composition and multi-layer microstructure. This study focused on experimental characterization of the effect of important influencing factors, including manufacturing process temperature, exposure temperature, and water absorption, on the impact damage threshold and damage mechanisms of flax fiber reinforced composites. Firstly, serious reduction on the impact damage threshold and damage resistance was observed, this indicated excessive temperature can cause chemical decomposition and structural damage to flax fiber. It was also shown that a moderate high temperature resulted in lower impact damage threshold. Moreover, a small amount of water absorption could slightly improve the damage threshold load and the damage resistance. However, more water uptake caused severe degradation on the composite interface and structural damage of flax fiber, which reduced the impact performance of flax fiber reinforced composites.

Sign in / Sign up

Export Citation Format

Share Document