A simple model for electrical conductivity of polymer carbon nanotubes nanocomposites assuming the filler properties, interphase dimension, network level, interfacial tension and tunneling distance

2018 ◽  
Vol 155 ◽  
pp. 252-260 ◽  
Author(s):  
Yasser Zare ◽  
Kyong Yop Rhee
Keyword(s):  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Simple Model ◽  
Interfacial Tension ◽  
Tunneling Distance

scholarly journals Effect of SWCNT-Tuball Paper on the Lightning Strike Protection of CFRPs and Their Selected Mechanical Properties

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3140
Author(s):  
Kamil Dydek ◽  
Anna Boczkowska ◽  
Rafał Kozera ◽  
Paweł Durałek ◽  
Łukasz Sarniak ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Copper Foil ◽  
Impact Resistance ◽  
Mechanical Analysis ◽  
Lightning Strike ◽  
Single Wall Carbon Nanotubes ◽  
Carbon Fibre Reinforced Polymer ◽  
The Impact

The main aim of this work was the investigation of the possibility of replacing the heavy metallic meshes applied onto the composite structure in airplanes for lightning strike protection with a thin film of Tuball single-wall carbon nanotubes in the form of ultra-light, conductive paper. The Tuball paper studied contained 75 wt% or 90 wt% of carbon nanotubes and was applied on the top of carbon fibre reinforced polymer before fabrication of flat panels. First, the electrical conductivity, impact resistance and thermo-mechanical properties of modified laminates were measured and compared with the reference values. Then, flat panels with selected Tuball paper, expanded copper foil and reference panels were fabricated for lightning strike tests. The effectiveness of lightning strike protection was evaluated by using the ultrasonic phased-array technique. It was found that the introduction of Tuball paper on the laminates surface improved both the surface and the volume electrical conductivity by 8800% and 300%, respectively. The impact resistance was tested in two directions, perpendicular and parallel to the carbon fibres, and the values increased by 9.8% and 44%, respectively. The dynamic thermo-mechanical analysis showed higher stiffness and a slight increase in glass transition temperature of the modified laminates. Ultrasonic investigation after lightning strike tests showed that the effectiveness of Tuball paper is comparable to expanded copper foil.

scholarly journals Enhancement of Electrical Conductivity of Aluminum-Based Nanocomposite Produced by Spark Plasma Sintering

Nanomaterials ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 1150
Author(s):  
Nicolás A. Ulloa-Castillo ◽  
Roberto Hernández-Maya ◽  
Jorge Islas-Urbano ◽  
Oscar Martínez-Romero ◽  
Emmanuel Segura-Cárdenas ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Spark Plasma Sintering ◽  
Experimental Tests ◽  
Powder Morphology ◽  
Plasma Sintering ◽  
Multi Walled Carbon Nanotubes ◽  
Spark Plasma ◽  
Ball Milling Technique ◽  
Walled Carbon Nanotubes

This article focuses on exploring how the electrical conductivity and densification properties of metallic samples made from aluminum (Al) powders reinforced with 0.5 wt % concentration of multi-walled carbon nanotubes (MWCNTs) and consolidated through spark plasma sintering (SPS) process are affected by the carbon nanotubes dispersion and the Al particles morphology. Experimental characterization tests performed by scanning electron microscopy (SEM) and by energy dispersive spectroscopy (EDS) show that the MWCNTs were uniformly ball-milled and dispersed in the Al surface particles, and undesirable phases were not observed in X-ray diffraction measurements. Furthermore, high densification parts and an improvement of about 40% in the electrical conductivity values were confirmed via experimental tests performed on the produced sintered samples. These results elucidate that modifying the powder morphology using the ball-milling technique to bond carbon nanotubes into the Al surface particles aids the ability to obtain highly dense parts with increasing electrical conductivity properties.

scholarly journals Electrically Conductive Networks from Hybrids of Carbon Nanotubes and Graphene Created by Laser Radiation

Nanomaterials ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1875
Author(s):  
Alexander Yu. Gerasimenko ◽  
Artem V. Kuksin ◽  
Yury P. Shaman ◽  
Evgeny P. Kitsyuk ◽  
Yulia O. Fedorova ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Laser Irradiation ◽  
Flexible Electronics ◽  
Threshold Energy ◽  
Wavelength Region ◽  
Hybrid Nanostructures ◽  
Graphene Sheets ◽  
Electrically Conductive ◽  
Walled Carbon Nanotubes

A technology for the formation of electrically conductive nanostructures from single-walled carbon nanotubes (SWCNT), multi-walled carbon nanotubes (MWCNT), and their hybrids with reduced graphene oxide (rGO) on Si substrate has been developed. Under the action of single pulses of laser irradiation, nanowelding of SWCNT and MWCNT nanotubes with graphene sheets was obtained. Dependences of electromagnetic wave absorption by films of short and long nanotubes with subnanometer and nanometer diameters on wavelength are calculated. It was determined from dependences that absorption maxima of various types of nanotubes are in the wavelength region of about 266 nm. It was found that contact between nanotube and graphene was formed in time up to 400 fs. Formation of networks of SWCNT/MWCNT and their hybrids with rGO at threshold energy densities of 0.3/0.5 J/cm2 is shown. With an increase in energy density above the threshold value, formation of amorphous carbon nanoinclusions on the surface of nanotubes was demonstrated. For all films, except the MWCNT film, an increase in defectiveness after laser irradiation was obtained, which is associated with appearance of C–C bonds with neighboring nanotubes or graphene sheets. CNTs played the role of bridges connecting graphene sheets. Laser-synthesized hybrid nanostructures demonstrated the highest hardness compared to pure nanotubes. Maximum hardness (52.7 GPa) was obtained for MWCNT/rGO topology. Regularity of an increase in electrical conductivity of nanostructures after laser irradiation has been established for films made of all nanomaterials. Hybrid structures of nanotubes and graphene sheets have the highest electrical conductivity compared to networks of pure nanotubes. Maximum electrical conductivity was obtained for MWCNT/rGO hybrid structure (~22.6 kS/m). Networks of nanotubes and CNT/rGO hybrids can be used to form strong electrically conductive interconnections in nanoelectronics, as well as to create components for flexible electronics and bioelectronics, including intelligent wearable devices (IWDs).

Dielectric properties of Shell oil transformer oil with impurities of carbon nanotubes and fullerene C60

2021 ◽  
Vol 24 (04) ◽  
pp. 413-418
Author(s):  
O.V. Kovalchuk ◽  
◽  
I.P. Studenyak ◽  
T.M. Kovalchuk ◽  
E.A. Ayryan ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Dielectric Properties ◽  
Fullerene C60 ◽  
Transformer Oil ◽  
C60 Fullerene ◽  
Cooling Efficiency ◽  
Fullerene Concentration ◽  
Multiwall Nanotubes

At the temperature 293 K, the influence of two types of nanoimpurities (carbon multiwall nanotubes and C60 fullerene) both separately and together on the dielectric properties of Shell oil transformer oil has been studied. It has been shown that these impurities do not significantly effect on the value of the dielectric permittivity of Shell oil, but more significantly increase its conductivity. It has been found that in the presence of nanotubes inside Shell oil, the dependence of its electrical conductivity on the fullerene concentration is nonmonotonic. The samples with the fullerene concentration 100 ppm have the highest conductivity. At the fullerene concentration 300 ppm, the conductivity of Shell oil with the impurities of carbon nanotube and C60 fullerene becomes almost equal to the electrical conductivity of Shell oil only with the impurities of carbon nanotubes. It has been suggested that C60 fullerene can be used to reduce the electrical conductivity of Shell oil with magnetic nanoparticles required to increase the cooling efficiency of transformers under the action of their own magnetic field.

PLA/Carbon Nanotubes Multifilament Yarns for Relative Humidity Textile Sensor

2011 ◽  
Vol 6 (3) ◽  
pp. 155892501100600 ◽  
Author(s):  
Eric Devaux ◽  
Carole Aubry ◽  
Christine Campagne ◽  
Maryline Rochery
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Relative Humidity ◽  
Melt Spinning ◽  
Flexible Sensor ◽  
Spinning Process ◽  
Textile Sensor ◽  
Multifilament Yarns

Polylactide (PLA) was mixed with 4 wt.% of carbon nanotubes (CNTs) to produce electrical conductive multifilament yarns by melt spinning process for humidity detection. Thanks to a variation of electrical conductivity, this flexible sensor could detect the moisture presence. The introduction of plasticizer was necessary to ensure higher fluidity and drawability of the blend during the spinning process. The plasticizer modifies the crystallinity and the mechanical properties of the yarns. The effectiveness of this sensor (PLA/4 wt.% CNTs fibres) sensitive to humidity, is optimal when the spinning conditions are adapted. In this way, the temperature and the rate of the drawing roll were reduced. The influence of these parameters on the crystallinity, the mechanical properties and the sensitivity of the yarns were studied. Once the appropriate spinning conditions found, one humidity sensitive yarn was processed and the repeatability and efficient reversibility of its sensitivity were highlighted.

Sign in / Sign up

Export Citation Format

Share Document