The effective Young’s modulus of composites beyond the Voigt estimation due to the Poisson effect

2009 ◽  
Vol 69 (13) ◽  
pp. 2198-2204 ◽  
Author(s):  
Bin Liu ◽  
Xue Feng ◽  
Si-Ming Zhang
Keyword(s):  
Young’S Modulus ◽  
Young's Modulus ◽  
Poisson Effect

Mechanical properties of FeAlSi powders prepared by mechanical alloying from different initial feedstock materials

2019 ◽  
Vol 107 (2) ◽  
pp. 207 ◽  
Author(s):  
Jaroslav Čech ◽  
Petr Haušild ◽  
Miroslav Karlík ◽  
Veronika Kadlecová ◽  
Jiří Čapek ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Alloying ◽  
Young’S Modulus ◽  
Milling Time ◽  
Young's Modulus ◽  
Element Model ◽  
X Ray Diffraction ◽  
X Ray ◽  
Powder Particles ◽  
Complete Homogenization

FeAl20Si20 (wt.%) powders prepared by mechanical alloying from different initial feedstock materials (Fe, Al, Si, FeAl27) were investigated in this study. Scanning electron microscopy, X-ray diffraction and nanoindentation techniques were used to analyze microstructure, phase composition and mechanical properties (hardness and Young’s modulus). Finite element model was developed to account for the decrease in measured values of mechanical properties of powder particles with increasing penetration depth caused by surrounding soft resin used for embedding powder particles. Progressive homogenization of the powders’ microstructure and an increase of hardness and Young’s modulus with milling time were observed and the time for complete homogenization was estimated.

Degradation of Rocks, Through Cracking Caused by Differential Thermal Expansion, in Relation to Nuclear Waste Repositories

1981 ◽  
Vol 6 ◽  
Author(s):  
J.R. Mclaren ◽  
R.W. Davidge ◽  
I. Titchell ◽  
K. Sincock ◽  
A. Bromley
Keyword(s):  
Thermal Expansion ◽  
Grain Boundary ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Crack Density ◽  
Granitic Rocks ◽  
Multiphase Materials ◽  
Thermal Expansion Behaviour ◽  
Waste Repositories ◽  
Expansion Behaviour

ABSTRACTHeating to temperatures up to 500°C, gives a reduction in Young's modulus and increase in permeability of granitic rocks and it is likely that a major reason is grain boundary cracking. The cracking of grain boundary facets in polycrystalline multiphase materials showing anisotropic thermal expansion behaviour is controlled by several microstructural factors in addition to the intrinsic thermal and elastic properties. Of specific interest are the relative orientations of the two grains meeting at the facet, and the size of the facet; these factors thus introduce two statistical aspects to the problem and these are introduced to give quantitative data on crack density versus temperature. The theory is compared with experimental measurements of Young's modulus and permeability for various rocks as a function of temperature. There is good qualitative agreement, and the additional (mainly microstructural) data required for a quantitative comparison are defined.

Is it necessary to calculate Young’s modulus in AFM nanoindentation experiments regarding biological samples?

2020 ◽  
Vol 12 ◽  
Author(s):  
S.V. Kontomaris ◽  
A. Malamou ◽  
A. Stylianou
Keyword(s):  
Young’S Modulus ◽  
Biological Samples ◽  
Young's Modulus ◽  
Reference Sample ◽  
Nonlinear Behavior ◽  
Accurate Method ◽  
Accurate Solution ◽  
Hertz Model ◽  
Work Done

Background: The determination of the mechanical properties of biological samples using Atomic Force Microscopy (AFM) at the nanoscale is usually performed using basic models arising from the contact mechanics theory. In particular, the Hertz model is the most frequently used theoretical tool for data processing. However, the Hertz model requires several assumptions such as homogeneous and isotropic samples and indenters with perfectly spherical or conical shapes. As it is widely known, none of these requirements are 100 % fulfilled for the case of indentation experiments at the nanoscale. As a result, significant errors arise in the Young’s modulus calculation. At the same time, an analytical model that could account complexities of soft biomaterials, such as nonlinear behavior, anisotropy, and heterogeneity, may be far-reaching. In addition, this hypothetical model would be ‘too difficult’ to be applied in real clinical activities since it would require very heavy workload and highly specialized personnel. Objective: In this paper a simple solution is provided to the aforementioned dead-end. A new approach is introduced in order to provide a simple and accurate method for the mechanical characterization at the nanoscale. Method: The ratio of the work done by the indenter on the sample of interest to the work done by the indenter on a reference sample is introduced as a new physical quantity that does not require homogeneous, isotropic samples or perfect indenters. Results: The proposed approach, not only provides an accurate solution from a physical perspective but also a simpler solution which does not require activities such as the determination of the cantilever’s spring constant and the dimensions of the AFM tip. Conclusion: The proposed, by this opinion paper, solution aims to provide a significant opportunity to overcome the existing limitations provided by Hertzian mechanics and apply AFM techniques in real clinical activities.

Effect of Microcrystalline Cellulose from Banana Stem Fiber on Mechanical Properties and Crystallinity of PLA Composite Films

2011 ◽  
Vol 695 ◽  
pp. 170-173 ◽  
Author(s):  
Voravadee Suchaiya ◽  
Duangdao Aht-Ong
Keyword(s):  
Tensile Strength ◽  
Young’S Modulus ◽  
Microcrystalline Cellulose ◽  
Young's Modulus ◽  
Agricultural Waste ◽  
Composite Films ◽  
Sem Image ◽  
Biocomposite Films ◽  
Twin Screw ◽  
Banana Stem

This work focused on the preparation of the biocomposite films of polylactic acid (PLA) reinforced with microcrystalline cellulose (MCC) prepared from agricultural waste, banana stem fiber, and commercial microcrystalline cellulose, Avicel PH 101. Banana stem microcrystalline cellulose (BS MCC) was prepared by three steps, delignification, bleaching, and acid hydrolysis. PLA and two types of MCC were processed using twin screw extruder and fabricated into film by a compression molding. The mechanical and crystalline behaviors of the biocomopsite films were investigated as a function of type and amount of MCC. The tensile strength and Young’s modulus of PLA composites were increased when concentration of MCC increased. Particularly, banana stem (BS MCC) can enhance tensile strength and Young’s modulus of PLA composites than the commercial MCC (Avicel PH 101) because BS MCC had better dispersion in PLA matrix than Avicel PH 101. This result was confirmed by SEM image of fractured surface of PLA composites. In addition, XRD patterns of BS MCC/PLA composites exhibited higher crystalline peak than that of Avicel PH 101/PLA composites

scholarly journals Out-of-Plane Thermal Expansion Coefficient and Biaxial Young’s Modulus of Sputtered ITO Thin Films

Coatings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 153
Author(s):  
Chuen-Lin Tien ◽  
Tsai-Wei Lin
Keyword(s):  
Thin Films ◽  
Thermal Expansion ◽  
Thermal Stress ◽  
Young’S Modulus ◽  
Thermal Expansion Coefficient ◽  
Expansion Coefficient ◽  
Young's Modulus ◽  
Heating Temperature ◽  
Glass Substrates ◽  
Ito Thin Films

This paper proposes a measuring apparatus and method for simultaneous determination of the thermal expansion coefficient and biaxial Young’s modulus of indium tin oxide (ITO) thin films. ITO thin films simultaneously coated on N-BK7 and S-TIM35 glass substrates were prepared by direct current (DC) magnetron sputtering deposition. The thermo-mechanical parameters of ITO thin films were investigated experimentally. Thermal stress in sputtered ITO films was evaluated by an improved Twyman–Green interferometer associated with wavelet transform at different temperatures. When the heating temperature increased from 30 °C to 100 °C, the tensile thermal stress of ITO thin films increased. The increase in substrate temperature led to the decrease of total residual stress deposited on two glass substrates. A linear relationship between the thermal stress and substrate heating temperature was found. The thermal expansion coefficient and biaxial Young’s modulus of the films were measured by the double substrate method. The results show that the out of plane thermal expansion coefficient and biaxial Young’s modulus of the ITO film were 5.81 × 10−6 °C−1 and 475 GPa.

scholarly journals Correction to: Hydric Cycle Impacts on COx Argillite Permeability and Young’s Modulus

2021 ◽  
Vol 54 (3) ◽  
pp. 1149-1149
Author(s):  
Zhibo Duan ◽  
Frédéric Skoczylas ◽  
Chuanrui Wang ◽  
Jean Talandier
Keyword(s):  
Young’S Modulus ◽  
Young's Modulus

scholarly journals Developing a Quantifying Device for Soft Tissue Material Prop-Erties around Lumbar Spines

Biosensors ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 67
Author(s):  
Song Joo Lee ◽  
Yong-Eun Cho ◽  
Kyung-Hyun Kim ◽  
Deukhee Lee
Keyword(s):  
Lumbar Spine ◽  
Soft Tissue ◽  
Young’S Modulus ◽  
Viscoelastic Properties ◽  
Soft Tissues ◽  
Young's Modulus ◽  
Strain Curve ◽  
Stress And Strain ◽  
Commercial Device ◽  
Tissue Material

Knowing the material properties of the musculoskeletal soft tissue could be important to develop rehabilitation therapy and surgical procedures. However, there is a lack of devices and information on the viscoelastic properties of soft tissues around the lumbar spine. The goal of this study was to develop a portable quantifying device for providing strain and stress curves of muscles and ligaments around the lumbar spine at various stretching speeds. Each sample was conditioned and applied for 20 repeatable cyclic 5 mm stretch-and-relax trials in the direction and perpendicular direction of the fiber at 2, 3 and 5 mm/s. Our device successfully provided the stress and strain curve of the samples and our results showed that there were significant effects of speed on the young’s modulus of the samples (p < 0.05). Compared to the expensive commercial device, our lower-cost device provided comparable stress and strain curves of the sample. Based on our device and findings, various sizes of samples can be measured and viscoelastic properties of the soft tissues can be obtained. Our portable device and approach can help to investigate young’s modulus of musculoskeletal soft tissues conveniently, and can be a basis for developing a material testing device in a surgical room or various lab environments.

Sign in / Sign up

Export Citation Format

Share Document