scholarly journals Stiffness and failure behaviour of folded sandwich cores under combined transverse shear and compression

2007 ◽  
Vol 38 (5) ◽  
pp. 1288-1295 ◽  
Author(s):  
M. Kintscher ◽  
L. Kärger ◽  
A. Wetzel ◽  
D. Hartung
Keyword(s):  
Transverse Shear ◽  
Failure Behaviour ◽  
Transverse Shear And Compression

On the nominal transverse shear strain to characterize the severity of creasing

TAPPI Journal ◽  
2018 ◽  
Vol 17 (04) ◽  
pp. 231-240
Author(s):  
Douglas Coffin ◽  
Joel Panek
Keyword(s):  
Shear Strain ◽  
Transverse Shear ◽  
Elastic Limit ◽  
Experimental Results ◽  
Transverse Shear Strain ◽  
Maximum Strain ◽  
Machine Direction ◽  
Engineering Approach ◽  
Wide Range ◽  
Analytic Expression

A transverse shear strain was utilized to characterize the severity of creasing for a wide range of tooling configurations. An analytic expression of transverse shear strain, which accounts for tooling geometry, correlated well with relative crease strength and springback as determined from 90° fold tests. The experimental results show a minimum strain (elastic limit) that needs to be exceeded for the relative crease strength to be reduced. The theory predicts a maximum achievable transverse shear strain, which is further limited if the tooling clearance is negative. The elastic limit and maximum strain thus describe the range of interest for effective creasing. In this range, cross direction (CD)-creased samples were more sensitive to creasing than machine direction (MD)-creased samples, but the differences were reduced as the shear strain approached the maximum. The presented development provides the foundation for a quantitative engineering approach to creasing and folding operations.

A Simple Model for Cornering and Belt-edge Separation in Radial Tires

1986 ◽  
Vol 14 (1) ◽  
pp. 3-32 ◽  
Author(s):  
P. Popper ◽  
C. Miller ◽  
D. L. Filkin ◽  
W. J. Schaffers
Keyword(s):  
Simple Model ◽  
Transverse Shear ◽  
Mathematical Analysis ◽  
Pure Bending ◽  
Radial Tire ◽  
Optimum Angle ◽  
Shear Strains ◽  
Interlaminar Shear ◽  
Edge Separation ◽  
Shear Bending

Abstract A mathematical analysis of radial tire cornering was performed to predict tire deflections and belt-edge separation strains. The model includes the effects of pure bending, transverse shear bending, lateral restraint of the carcass on the belt, and shear displacements between belt and carcass. It also provides a description of the key mechanisms that act during cornering. The inputs include belt and carcass cord properties, cord angle, pressure, rubber properties, and cornering force. Outputs include cornering deflections and interlaminar shear strains. Key relations found between tire parameters and responses were the optimum angle for minimum cornering deflections and its dependence on cord modulus, and the effect of cord angle and modulus on interlaminar shear strains.

Determination of the transverse shear stress in layered composites

2020 ◽  
Vol 86 (2) ◽  
pp. 44-53
Author(s):  
Yu. I. Dudarkov ◽  
M. V. Limonin
Keyword(s):  
Shear Stress ◽  
Transverse Shear ◽  
Composite Beam ◽  
Layered Composite ◽  
Equivalent Model ◽  
Shear Stresses ◽  
Transverse Shear Stress ◽  
Layered Composites ◽  
Laminate Composites ◽  
Transverse Shear Stresses

An engineering approach to estimation of the transverse shear stresses in layered composites is developed. The technique is based on the well-known D. I. Zhuravsky equation for shear stresses in an isotropic beam upon transverse bending. In general, application of this equation to a composite beam is incorrect due to the heterogeneity of the composite structure. According to the proposed method, at the first stage of its implementation, a transition to the equivalent model of a homogeneous beam is made, for which the Zhuravsky formula is valid. The transition is carried out by changing the shape of the cross section of the beam, provided that the bending stiffness and generalized elastic modulus remain the same. The calculated shear stresses in the equivalent beam are then converted to the stress values in the original composite beam from the equilibrium condition. The main equations and definitions of the method as well as the analytical equation for estimation of the transverse shear stress in a composite beam are presented. The method is verified by comparing the analytical solution and the results of the numerical solution of the problem by finite element method (FEM). It is shown that laminate stacking sequence has a significant impact both on the character and on the value of the transverse shear stress distribution. The limits of the applicability of the developed technique attributed to the conditions of the validity of the hypothesis of straight normal are considered. It is noted that under this hypothesis the shear stresses do not depend on the layer shear modulus, which explains the absence of this parameter in the obtained equation. The classical theory of laminate composites is based on the similar assumptions, which gives ground to use this equation for an approximate estimation of the transverse shear stresses in in a layered composite package.

Finite element bending analysis of symmetric and non-symmetric functionally graded sandwich beams using a novel parabolic shear deformation theory

2021 ◽  
pp. 146442072110050
Author(s):  
Mohamed-Ouejdi Belarbi ◽  
Abdelhak Khechai ◽  
Aicha Bessaim ◽  
Mohammed-Sid-Ahmed Houari ◽  
Aman Garg ◽  
...  
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Shear Deformation ◽  
Transverse Shear ◽  
Deformation Theory ◽  
Shear Deformation Theory ◽  
Element Model ◽  
Beam Element ◽  
Functionally Graded ◽  
Sandwich Beams

In this paper, the bending behavior of functionally graded single-layered, symmetric and non-symmetric sandwich beams is investigated according to a new higher order shear deformation theory. Based on this theory, a novel parabolic shear deformation function is developed and applied to investigate the bending response of sandwich beams with homogeneous hardcore and softcore. The present theory provides an accurate parabolic distribution of transverse shear stress across the thickness and satisfies the zero traction boundary conditions on the top and bottom surfaces of the functionally graded sandwich beam without using any shear correction factors. The governing equations derived herein are solved by employing the finite element method using a two-node beam element, developed for this purpose. The material properties of functionally graded sandwich beams are graded through the thickness according to the power-law distribution. The predictive capability of the proposed finite element model is demonstrated through illustrative examples. Four types of beam support, i.e. simply-simply, clamped-free, clamped–clamped, and clamped-simply, are used to study how the beam deflection and both axial and transverse shear stresses are affected by the variation of volume fraction index and beam length-to-height ratio. Results of the numerical analysis have been reported and compared with those available in the open literature to evaluate the accuracy and robustness of the proposed finite element model. The comparisons with other higher order shear deformation theories verify that the proposed beam element is accurate, presents fast rate of convergence to the reference results and it is also valid for both thin and thick functionally graded sandwich beams. Further, some new results are reported in the current study, which will serve as a benchmark for future research.

Failure behaviour of cladding made from Sv 07Kh25N13 austenitic stainless steel

2021 ◽  
Vol 189 ◽  
pp. 104275
Author(s):  
J. Štefan ◽  
J. Siegl ◽  
J. Adámek ◽  
R. Kopřiva ◽  
M. Kytka
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Failure Behaviour
Sign in / Sign up

Export Citation Format

Share Document