Mechanical properties of textile-inserted PP/PP knitted composites using injection–compression molding

2006 ◽  
Vol 37 (12) ◽  
pp. 2285-2299 ◽  
Author(s):  
O.A. Khondker ◽  
X. Yang ◽  
N. Usui ◽  
H. Hamada
Keyword(s):  
Mechanical Properties ◽  
Compression Molding ◽  
Injection Compression Molding

Study on Optical Properties of Microstructure of Lightguiding Plate for Micro Injection Molding and Micro Injection-Compression Molding

2006 ◽  
Vol 505-507 ◽  
pp. 229-234 ◽  
Author(s):  
Yung Kang Shen ◽  
H.J. Chang ◽  
C.T. Lin
Keyword(s):  
Optical Properties ◽  
Injection Molding ◽  
Digital Camera ◽  
Mold Temperature ◽  
Compression Molding ◽  
Micro Injection Molding ◽  
Melt Temperature ◽  
Packing Pressure ◽  
Injection Compression Molding ◽  
Better Than

The purpose of this paper presents the optical properties of microstructure of lightguiding plate for micro injection molding (MIM) and micro injection-compression molding (MICM). The lightguiding plate is applied on LCD of two inch of digital camera. Its radius of microstructure is from 100μm to 300μm by linearity expansion. The material of lightguiding plate uses the PMMA plastic. This paper uses the luminance distribution to make a comparison between MIM and MICM for the optical properties of lightguiding plate. The important parameters of process for optical properties are the mold temperature, melt temperature and packing pressure in micro injection molding. The important parameters of process for optical properties are the compression distance, mold temperature and compression speed in micro injection-compression molding. The process of micro injection-compression molding is better than micro injection molding for optical properties.

A Theoretical Analysis on Resin Injection/Compression Molding

2007 ◽  
Vol 334-335 ◽  
pp. 209-212 ◽  
Author(s):  
Akbar Shojaei ◽  
A. Spah
Keyword(s):  
Analytical Solutions ◽  
Mold Filling ◽  
Compression Molding ◽  
Fiber Content ◽  
Flow Front ◽  
Transfer Molding ◽  
Unidirectional Flow ◽  
Resin Injection ◽  
Filling Time ◽  
Injection Compression Molding

In the present investigation, mold filling process of resin injection/compression molding (RI/CM) is compared with resin transfer molding (RTM) for simple mold geometry. To do this, analytical solutions are obtained for RI/CM in unidirectional flow. Based on the analytical solutions, flow front progression and pressure distribution are compared with RTM at different fiber content. The results indicate that the RI/CM reduces the mold filling time significantly, particularly for composite parts with higher fiber content.

Effect of Filler Compositions on the Mechanical Properties of Bamboo Filled Polyester Composite

2014 ◽  
Vol 879 ◽  
pp. 90-95 ◽  
Author(s):  
Abdul Rahman Noor Leha ◽  
Nor Amalina Nordin
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Impact Test ◽  
Compression Molding ◽  
Engineering Applications ◽  
Maximum Value ◽  
Polyester Composite ◽  
Bamboo Powder ◽  
Flexural Tests ◽  
The Impact

Biocomposite from bamboo powder was fabricated by compression molding technique. The objective of this study was to investigate the mechanical properties of bamboo compounded with epoxy with different ratio. Tensile and flexural tests were done to characterize its mechanical properties. It was observed that the strength of bamboo-polyester was increased with increasing amount of bamboo powder. The tensile and flexural strength shows the highest value at 25 wt.% bamboo. However, the impact test shows the maximum value at 20 wt.% bamboo powder. These results exhibit the bamboo-polyester can be a good candidate to be used in many engineering applications

scholarly journals Hedysarum coronarium-Based Green Composites Prepared by Compression Molding and Fused Deposition Modeling

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 465
Author(s):  
Roberto Scaffaro ◽  
Maria Clara Citarrella ◽  
Emmanuel Fortunato Gulino ◽  
Marco Morreale
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Fused Deposition Modeling ◽  
Young's Modulus ◽  
Compression Molding ◽  
Green Composite ◽  
Fused Deposition ◽  
Hedysarum Coronarium ◽  
Deposition Modeling ◽  
Fibers Orientation

In this work, an innovative green composite was produced by adding Hedysarum coronarium (HC) flour to a starch-based biodegradable polymer (Mater-Bi®, MB). The flour was obtained by grinding together stems, leaves and flowers and subsequently sieving it, selecting a fraction from 75 μm to 300 μm. Four formulations have been produced by compression molding (CM) and fused deposition modeling (FDM) by adding 5%, 10%, 15% and 20% of HC to MB. The influence of filler content on the processability was tested, and rheological, morphological and mechanical properties of composites were also assessed. Through CM, it was possible to obtain easily homogeneous samples with all filler amounts. Concerning FDM, 5% and 10% HC-filled composites proved also easily printable. Mechanical results showed filler effectively acted as reinforcement: Young’s modulus and tensile strengths of the composites increased from 74.3 MPa to 236 MPa and from 18.6 MPa to 33.4 MPa, respectively, when 20% of HC was added to the pure matrix. FDM samples, moreover, showed higher mechanical properties if compared with CM ones due to rectilinear infill and fibers orientation. In fact, regarding the 10% HC composites, Young’s modulus of the CM and FDM ones displayed a relative increment of 176% and 224%, respectively.

scholarly journals Compression Molding and Mechanical Properties of Green-Composite Based on Ramie/PLA Non-Twisted Commingled Yarn

2004 ◽  
Vol 53 (7) ◽  
pp. 776-781 ◽  
Author(s):  
Teruo KIMURA ◽  
Masahiro KURATA ◽  
Tatsuki MATSUO ◽  
Hirokazu MATSUBARA ◽  
Tadayuki SAKOBE
Keyword(s):  
Mechanical Properties ◽  
Compression Molding ◽  
Green Composite ◽  
Commingled Yarn
Sign in / Sign up

Export Citation Format

Share Document