Application of the two-phase three-component computational model to predict cavitating flow in a centrifugal pump and its validation

2016 ◽  
Vol 131 ◽  
pp. 142-150 ◽  
Author(s):  
Yong Wang ◽  
Houlin Liu ◽  
Dongxi Liu ◽  
Shouqi Yuan ◽  
Jian Wang ◽  
...  
Keyword(s):  
Computational Model ◽  
Centrifugal Pump ◽  
Cavitating Flow ◽  
Two Phase

CFD analysis of two‐phase cavitating flow in a centrifugal pump with an inducer

Heat Transfer ◽  
2020 ◽  
Vol 49 (6) ◽  
pp. 3854-3881
Author(s):  
Debarpan Paul ◽  
Himanshu Agarwal ◽  
Babu Rao Ponangi
Keyword(s):  
Centrifugal Pump ◽  
Cavitating Flow ◽  
Cfd Analysis ◽  
Two Phase

Experimental analysis of two-phase flow in a radial centrifugal pump

2017 ◽  
Author(s):  
Henrique Stel ◽  
Edgar Ofuchi ◽  
Dalton Bertoldi ◽  
Moisés Marcelino Neto ◽  
Rigoberto Morales ◽  
...  
Keyword(s):  
Centrifugal Pump ◽  
Experimental Analysis ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Two Phase

NUMERICAL EVALUATION OF THE TWO-PHASE FLOW IN A RADIAL CENTRIFUGAL PUMP

2018 ◽  
Author(s):  
Carlos Eduardo Ribeiro Santa Cruz Mendoza ◽  
Rafael Dunaiski ◽  
Edgar Ofuchi ◽  
Henrique Stel ◽  
Rigoberto Morales
Keyword(s):  
Centrifugal Pump ◽  
Numerical Evaluation ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Two Phase

A Method for Correlating the Characteristics of Centrifugal Pumps in Two-Phase Flow

1978 ◽  
Vol 100 (4) ◽  
pp. 395-409 ◽  
Author(s):  
Jaroslaw Mikielewicz ◽  
David Gordon Wilson ◽  
Tak-Chee Chan ◽  
Albert L. Goldfinch
Keyword(s):  
Centrifugal Pump ◽  
Two Phase Flow ◽  
Flow Direction ◽  
Semiempirical Method ◽  
Head Loss ◽  
Phase Flow ◽  
Loss Ratio ◽  
Centrifugal Pumps ◽  
Reversed Flow ◽  
Two Phase

The semiempirical method described combines the ideal performance of a centrifugal pump with experimental data for single and two-phase flow to produce a so-called “head-loss ratio,” which is the apparent loss of head in two-phase flow divided by the loss of head in single-phase flow. This head-loss ratio is shown to be primarily a function of void fraction. It is demonstrated that the measured characteristics of a centrifugal pump operating in two-phase flow in normal rotation and normal and reversed flow directions (first and second -quadrant operation) and in reversed rotation and reversed flow direction (third-quadrant operation) can be reproduced with acceptable accuracy.

Calculating Method for the Solid Phase Effect Coefficient of the Solid-Fluid Two Phase Flow Centrifugal Pump

2010 ◽  
Vol 29-32 ◽  
pp. 658-663
Author(s):  
Chuan Jun Li ◽  
Gang Yu ◽  
Xin Wang
Keyword(s):  
Differential Equation ◽  
Centrifugal Pump ◽  
Two Phase Flow ◽  
Solid Phase ◽  
High Accuracy ◽  
Phase Flow ◽  
Phase Effect ◽  
Two Phase ◽  
Error Band ◽  
Calculating Method

In order to acquire the solid-fluid two phase flow centrifugal pump’s slurry head according with the fact, the solid phase effect coefficient must be calculated precisely. By analysising the acting forces on the solid particle, its moving differential equation was established. And the calculating formula of the solid phase effect coefficient was deduced based on the equation. For the sake of verifying its validity, a test of contrast and comparison on the calculating slurry heads by some ways was carried out. The results shows that the relative error values of the slurry head calculated are less than 2.00% with a small and stably error band. The method has the advantage of simple calculating process, high accuracy, low randomness and good practicability.

scholarly journals Wear Characteristics of Dense Fine Particles Solid-Liquid Two-Phase Fluid Centrifugal Pump with Open Impellers

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Yanping Wang ◽  
Chuanfeng Han ◽  
Ye Zhou ◽  
Zhe Lin ◽  
Jianfeng Ma ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Volume Concentration ◽  
Fine Particles ◽  
Two Phase Flow ◽  
Middle Part ◽  
Phase Flow ◽  
Particle Volume ◽  
Two Phase ◽  
Wear Characteristics

The demand for a centrifugal pump with open impellers for conveying dense fine particles in solid-liquid two-phase flow has increased significantly in actual engineering. The wear of dense fine particles on the centrifugal pump is also exceedingly prominent, which affects the engineering efficiency and economic benefits. The two-phase flow in the open centrifugal pump is three-dimensional and unsteady; the movement of high-volume concentration particles in the centrifugal pump and its mutual influence on the two-phase flow, which results in the calculation of wear, are very intricate. To study the wear characteristics of the centrifugal pump with open impeller with high-volume concentration particles more accurately, numerical simulation and experimental comparison are carried out for the impeller wear of dense fine particles transported by the centrifugal pump with open impellers. Considering the relationship between particles and walls, we used the Fluent 18.0 built-in rebound function and wear model. The RNG k-ε model and the DDPM model were adopted in the numerical simulation, and the numerical solution for centrifugal pump wear was performed under flow rate (9.6 m3·h−1, 12.8 m3·h−1, 16 m3·h−1, and 19.2 m3·h−1), different particle sizes (0.048 mm, 0.106 mm, 0.15 mm, 0.27 mm, and 0.425 mm), and different particle volume concentrations (10%, 15%, 20%, 25%, and 30%), respectively. By comparing the serious wear positions of the impeller, the experimental results correspond well with the numerical simulation, which can be used to predict and study the wear characteristics of the impeller. The results show that the most serious area of blade wear is the middle part of the pressure surface, followed by the middle part of the upper part of the blade. The wear of the impeller is greatly affected by relevant parameters, such as pump flow rate, particle diameter, and particle volume concentration. These results can provide some basis for the wear-resistant design of dense fine particle impeller.

Sign in / Sign up

Export Citation Format

Share Document