Non-contact, fibrous cellulose acetate/aluminum flexible electronic-sensor for humidity detecting

2020 ◽  
Vol 20 ◽  
pp. 100347 ◽  
Author(s):  
Xiangyu Meng ◽  
Jianhui Yang ◽  
Zhenguo Liu ◽  
Weibing Lu ◽  
Yueming Sun ◽  
...  
Keyword(s):  
Cellulose Acetate ◽  
Electronic Sensor ◽  
Flexible Electronic ◽  
Fibrous Cellulose

A STUDY OF THE SULPHATE ESTER OF UNSTABILIZED CELLULOSE ACETATE

1954 ◽  
Vol 32 (6) ◽  
pp. 566-580 ◽  
Author(s):  
Karl Keirstead ◽  
John Myers
Keyword(s):  
Thermal Stability ◽  
Ion Exchange ◽  
Cellulose Acetate ◽  
Salt Solution ◽  
Sulphate Content ◽  
Fibrous Cellulose ◽  
Thermal Stability Of

Evidence for the existence of the ester form of the sulphate in unstabilized cellulose acetate has been examined by ion exchange studies on precipitated and fibrous cellulose acetate. The equilibrium reached during ion exchange is affected by the pH and by the concentration of the salt solution used. The thermal stability of the ester is shown to vary inversely with the sulphate content. A study has been made of the accuracy of the various analyses involved.

Cellulose Acetate Reverse Osmosis Membrane Structure

1972 ◽  
Vol 30 ◽  
pp. 528-529
Author(s):  
H. K. Plummer ◽  
E. Eichen ◽  
C. D. Melvin
Keyword(s):  
Cellulose Acetate ◽  
Reverse Osmosis ◽  
Membrane Structure ◽  
Freeze Drying ◽  
Dense Layer ◽  
Water Removal ◽  
Reverse Osmosis Membrane ◽  
Correct Interpretation ◽  
Electron Image ◽  
Scanning Electron

Much of the work reported in the literature on cellulose acetate reverse osmosis membranes has raised new and important questions with regard to the dense or “active” layer of these membranes. Several thickness values and structures have been attributed to the dense layer. To ensure the correct interpretation of the cellulose acetate structure thirteen different preparative techniques have been used in this investigation. These thirteen methods included various combinations of water substitution, freeze drying, freeze sectioning, fracturing, embedding, and microtomy techniques with both transmission and scanning electron microscope observations.It was observed that several factors can cause a distortion of the structure during sample preparation. The most obvious problem of water removal can cause swelling, shrinking, and folds. Improper removal of embedding materials, when used, can cause a loss of electron image contrast and, or structure which could hinder interpretation.

The Control of Cigarette Smoke Deliveries Using Heat-Shrinkable Films

1975 ◽  
Vol 8 (2) ◽  
Author(s):  
R. A. Crellin ◽  
G. O. Brooks ◽  
H. G. Horsewell
Keyword(s):  
Particulate Matter ◽  
Cellulose Acetate ◽  
Cigarette Smoke ◽  
Total Particulate Matter ◽  
Puff Volume ◽  
Cigarette Paper ◽  
High Degree

AbstractA ventilating filter for cigarettes has been developed which reduces the delivery of smoke constituents from the final two to three puffs. Since the normaI delivery for these three puffs can account for up to half the total particulate matter and nicotine delivered by the whole cigarette, usefuI reductions per cigarette can be produced. The ventilating filter consists of cellulose acetate tow wrapped in heat-shrinkable film and attached to a tobacco rod using perforated tipping paper. When the cigarette is smoked, the perforations remain closed by contact with the impermeable film until transfer of heat to the filter is sufficient to soften the filter tow and shrink the film. Ventilating air now enters the cigarette and reduces the smoke deliveries. The effectiveness of the ventilating filter is increased by using films which have a low shrink temperature, high shrink tension and a high degree of biaxiaI shrinkage. Increases in filter plasticiser level, tipping perforation area and puff volume improve the effectiveness of the ventilating filter but increases in cigarette paper porosity and tobacco butt length reduce the effectiveness

Sign in / Sign up

Export Citation Format

Share Document