Flow field of suspended solids in a stirred tank reactor by Lagrangian tracking

2007 ◽  
Vol 62 (22) ◽  
pp. 6143-6154 ◽  
Author(s):  
Debangshu Guha ◽  
P.A. Ramachandran ◽  
M.P. Dudukovic
Keyword(s):  
Flow Field ◽  
Suspended Solids ◽  
Stirred Tank ◽  
Stirred Tank Reactor ◽  
Tank Reactor ◽  
Lagrangian Tracking

scholarly journals Measurement of Lagrangian Trajectories in a 3 L Stirred Tank Reactor using 4D Particle Tracking Velocimetry with Shake-the-Box

2021 ◽  
Vol 1 (1) ◽  
Author(s):  
Jürgen Fitschen ◽  
Alexandra Von Kameke ◽  
Sebastian Hofmann ◽  
Marko Hoffmann ◽  
Michael Schlüter
Keyword(s):  
Flow Field ◽  
Particle Tracking ◽  
Particle Tracking Velocimetry ◽  
Three Dimensional ◽  
Field Measurements ◽  
Stirred Tank ◽  
Two Dimensional ◽  
Scientific Publications ◽  
Stirred Tank Reactor ◽  
Tank Reactor

Stirred tank reactors are widely used in the chemical industry and bioprocess engineering and, consequently, a large number of scientific publications deal with the characterization of those apparatuses. However, there is very little information about the flow conditions. This is mostly due to the fact that these apparatuses are generally made of stainless steel, which restricts optical access. Furthermore, three-dimensional flow field measurements are still not trivial and involve costly equipment, therefore, investigations often reduce to two-dimensional PIV measurements. Nevertheless, recent works (Rosseburg et al., 2018; Taghavi and Moghaddas, 2020; Kuschel et al., 2021) impressively show the formation of compartments which hinder and delay mixing. However, these measurements are based either on instantaneous concentration profiles by means of pLIF measurements or on a two-dimensional projection of the system and thus do not allow conclusions about the development of the three dimensional compartments and the exchange rates between the compartments. In this work, for the first time, instantaneous flow field measurements with high spatial and temporal resolution are performed in the entire volume of a 3L stirred tank reactor based on 4D particle tracking velocimetry. The highly resolved particle trajectories further allow detailed Lagrangian analysis of the mixing dynamics inside the reactor, data that was previously inaccessible.

Modeling and Experimental Study of a Stirred Tank Reactor

2006 ◽  
Vol 3 (1) ◽  
Author(s):  
Marc Dhainaut ◽  
Pål Tetlie ◽  
Knut Bech
Keyword(s):  
Flow Field ◽  
Momentum Equation ◽  
Experimental Results ◽  
Stirred Tank ◽  
Stirred Tank Reactor ◽  
Sliding Mesh ◽  
Tank Reactor ◽  
Modeling Approach ◽  
Vertical Sections ◽  
Mesh Technique

This study proposes a comparison between CFD (Computational Fluid Dynamics) and experimental results for a cylindrical stirred tank reactor. The stirred tank reactor considered here is 0.7 m high, 0.4 m in diameter, baffled and has four impeller blades on a single shaft, placed at the symmetry axis. The tank is filled with water and serves as a model for molten aluminium purifying reactors.The experimental part of the study compares the use of PIV and LDV techniques to determine the flow field inside the tank. We use PIV to get a complete picture of the flow field in two vertical sections of the tank (one radial and one eccentric). LDV is then used to check and compare the velocities obtained by PIV along horizontal lines belonging to the two vertical sections considered under the PIV-measurements. Good overall agreement between the two methods is obtained.The experimental results are compared to simulation of the tank using an alternative model that we have implemented in the commercial CFD software Fluent. The modeling approach we propose here avoids the classical sliding mesh technique and its tedious use (especially for pre- and post-processing). Our model does not physically represent the impeller blades. It rather introduces them as a time-dependent source term in the momentum equation. This term is only accounted for at the cells that would have been swept by a blade if the blades were present. The modeling of the tank and the set-up of the case are faster and easier. The computation of the flow field using this modeling approach is compared to the sliding mesh approach and to the experimental results discussed above. Results show good agreement between experimental data and both modeling approaches (sliding mesh technique and no impeller model). The model we propose does not bring more accuracy but more convenience in the modeling work.

Transient response of the 1-st order dynamic system with fluctuating parameters

1979 ◽  
Vol 44 (7) ◽  
pp. 2184-2195
Author(s):  
Vladimír Herles ◽  
Jan Čermák ◽  
Antonín Havlíček
Keyword(s):  
Dynamic System ◽  
Dynamic Behavior ◽  
Transient Response ◽  
Flow Model ◽  
Stirred Tank ◽  
Order System ◽  
Random Parameters ◽  
Stirred Tank Reactor ◽  
Tank Reactor ◽  
Theoretical Results

The paper deals with the analysis of the dynamic behavior of the 1st order system with two random parameters. The theoretical results have been compared with experiments on flow model of a stirred tank reactor.

scholarly journals Quantifying the reactive uptake of OH by organic aerosols in a continuous flow stirred tank reactor

2009 ◽  
Vol 11 (36) ◽  
pp. 7885 ◽  
Author(s):  
Dung L. Che ◽  
Jared D. Smith ◽  
Stephen R. Leone ◽  
Musahid Ahmed ◽  
Kevin R. Wilson
Keyword(s):  
Continuous Flow ◽  
Organic Aerosols ◽  
Stirred Tank ◽  
Stirred Tank Reactor ◽  
Tank Reactor
Sign in / Sign up

Export Citation Format

Share Document