Polymer dispersions and their interaction with mortar constituents and ceramic tile surfaces studied by zeta-potential measurements and atomic force microscopy

2012 ◽  
Vol 34 (5) ◽  
pp. 604-611 ◽  
Author(s):  
Josef Kaufmann ◽  
Frank Winnefeld ◽  
Roger Zurbriggen
Keyword(s):  
Atomic Force Microscopy ◽  
Zeta Potential ◽  
Ceramic Tile ◽  
Force Microscopy ◽  
Atomic Force ◽  
Polymer Dispersions

Comparison of atomic force microscopy and zeta potential derived surface charge density

2020 ◽  
Vol 130 (3) ◽  
pp. 36001
Author(s):  
M. Herzberg ◽  
S. Dobberschütz ◽  
D. Okhrimenko ◽  
N. E. Bovet ◽  
M. P. Andersson ◽  
...  
Keyword(s):  
Atomic Force Microscopy ◽  
Zeta Potential ◽  
Charge Density ◽  
Surface Charge ◽  
Surface Charge Density ◽  
Force Microscopy ◽  
Atomic Force

scholarly journals Response of Non-Polar Oil Component on Low Salinity Effect in Carbonate Reservoirs: Adhesion Force Measurement Using Atomic Force Microscopy

Energies ◽  
2019 ◽  
Vol 13 (1) ◽  
pp. 77 ◽  
Author(s):  
Nasser S. Al Maskari ◽  
Ahmad Sari ◽  
Md Mofazzal Hossain ◽  
Ali Saeedi ◽  
Quan Xie
Keyword(s):  
Contact Angle ◽  
Atomic Force Microscopy ◽  
Zeta Potential ◽  
Adhesion Force ◽  
Carbonate Reservoirs ◽  
Force Microscopy ◽  
Polar Components ◽  
Low Salinity ◽  
Atomic Force ◽  
Polar Oil

While the effect of polar-oil component on oil-brine-carbonate system wettability has been extensively investigated, there has been little quantitative analysis of the effect of non-polar components on system wettability, in particular as a function of pH. In this context, we measured the contact angle of non-polar oil on calcite surface in the presence of 10,000 ppm NaCl at pH values of 6.5, 9.5 and 11. We also measured the adhesion of non-polar oil group (–CH3) and calcite using atomic force microscopy (AFM) under the same conditions of contact angle measurements. Furthermore, to gain a deeper understanding, we performed zeta potential measurements of the non-polar oil-brine and brine-calcite interfaces, and calculated the total disjoining pressure. Our results show that the contact angle decreases from 125° to 78° with an increase in pH from 6.5 to 11. AFM measurements show that the adhesion force decreases with increasing pH. Zeta potential results indicate that an increase in pH would change the zeta potential of the non-polar oil-brine and calcite-brine interfaces towards more negative values, resulting in an increase of electrical double layer forces. The total disjoining pressure and results of AFM adhesion tests predict the same trend, showing that adhesion forces decrease with increasing pH. Our results show that the pH increase during low-salinity waterflooding in carbonate reservoirs would lift off non-polar components, thereby lowering residual oil saturation. This physiochemical process can even occur in reservoirs with low concentration of polar components in crude oils.

Electrostatic Forces on the Surface of Metals as Measured by Atomic Force Microscopy

2000 ◽  
Vol 10 (1-2) ◽  
pp. 15
Author(s):  
Eugene Sprague ◽  
Julio C. Palmaz ◽  
Cristina Simon ◽  
Aaron Watson
Keyword(s):  
Atomic Force Microscopy ◽  
Electrostatic Forces ◽  
Force Microscopy ◽  
Atomic Force
Sign in / Sign up

Export Citation Format

Share Document