Relaxation effects of magnetization modulus and precession axis on damping time of precession in L1 0 -ordered FePt alloy film

2017 ◽  
Vol 17 (7) ◽  
pp. 1009-1013
Author(s):  
Ji-Wan Kim ◽  
Hyon-Seok Song ◽  
Chun-Yeol You ◽  
Sung-Chul Shin
Keyword(s):  
Alloy Film ◽  
Fept Alloy ◽  
Relaxation Effects

scholarly journals Enhancement of L10 ordering with the c-axis perpendicular to the substrate in FePt alloy film by using an epitaxial cap-layer

AIP Advances ◽  
2017 ◽  
Vol 7 (5) ◽  
pp. 056320 ◽  
Author(s):  
Mitsuru Ohtake ◽  
Masahiro Nakamura ◽  
Masaaki Futamoto ◽  
Fumiyoshi Kirino ◽  
Nobuyuki Inaba
Keyword(s):  
Alloy Film ◽  
Fept Alloy ◽  
Cap Layer

scholarly journals Ordering and self-diffusion in FePt alloy film

2008 ◽  
Vol 10 (5) ◽  
pp. 053031 ◽  
Author(s):  
M Gupta ◽  
A Gupta ◽  
J Stahn ◽  
T Gutberlet
Keyword(s):  
Alloy Film ◽  
Self Diffusion ◽  
Fept Alloy

Stress Relaxation and the Formation of Silicides in the Process of the Crystallization of NI-NB Films on SI

1991 ◽  
Vol 49 ◽  
pp. 898-899
Author(s):  
N. Rozhanski ◽  
V. Lifshitz
Keyword(s):  
Thin Films ◽  
Stress Relaxation ◽  
Integrated Circuits ◽  
Direct Evidence ◽  
Alloy Film ◽  
Diffusion Barriers ◽  
Effective Barrier

Thin films of amorphous Ni-Nb alloys are of interest since they can be used as diffusion barriers for integrated circuits on Si. A native SiO2 layer is an effective barrier for Ni diffusion but it deformation during the crystallization of the alloy film lead to the appearence of diffusion fluxes through it and the following formation of silicides. This study concerns the direct evidence of the action of stresses in the process of the crystallization of Ni-Nb films on Si and the structure of forming NiSi2 islands.

Evolution of the microstructure of Cu(Ti)/SiO2 layers annealed in NH3

1995 ◽  
Vol 53 ◽  
pp. 452-453
Author(s):  
J. Liu ◽  
N. D. Theodore ◽  
D. Adams ◽  
S. Russell ◽  
T. L. Alford ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Titanium Nitride ◽  
Large Scale ◽  
Standard Procedure ◽  
Alloy Film ◽  
Electron Beam Evaporation ◽  
Copper Metallization ◽  
Nominal Composition ◽  
Ti Alloy ◽  
Thermally Grown

Copper-based metallization has recently attracted extensive research because of its potential application in ultra-large-scale integration (ULSI) of semiconductor devices. The feasibility of copper metallization is, however, limited due to its thermal stability issues. In order to utilize copper in metallization systems diffusion barriers such as titanium nitride and other refractory materials, have been employed to enhance the thermal stability of copper. Titanium nitride layers can be formed by annealing Cu(Ti) alloy film evaporated on thermally grown SiO2 substrates in an ammonia ambient. We report here the microstructural evolution of Cu(Ti)/SiO2 layers during annealing in NH3 flowing ambient.The Cu(Ti) films used in this experiment were prepared by electron beam evaporation onto thermally grown SiO2 substrates. The nominal composition of the Cu(Ti) alloy was Cu73Ti27. Thermal treatments were conducted in NH3 flowing ambient for 30 minutes at temperatures ranging from 450°C to 650°C. Cross-section TEM specimens were prepared by the standard procedure.

Atomic Layer Deposition of LiF and Lithium Ion Conducting (AlF3)(LiF)x Alloys Using Trimethylaluminum, Lithium Hexamethyldisilazide and Hydrogen Fluoride

2017 ◽  
Author(s):  
Younghee Lee ◽  
Daniela M. Piper ◽  
Andrew S. Cavanagh ◽  
Matthias J. Young ◽  
Se-Hee Lee ◽  
...  
Keyword(s):  
Lithium Ion ◽  
Atomic Layer ◽  
Mass Gain ◽  
Alloy Film ◽  
Ex Situ ◽  
X Ray ◽  
Layer Deposition ◽  
Ion Conducting ◽  
Good Agreement

<div>Atomic layer deposition (ALD) of LiF and lithium ion conducting (AlF<sub>3</sub>)(LiF)<sub>x</sub> alloys was developed using trimethylaluminum, lithium hexamethyldisilazide (LiHMDS) and hydrogen fluoride derived from HF-pyridine solution. ALD of LiF was studied using in situ quartz crystal microbalance (QCM) and in situ quadrupole mass spectrometer (QMS) at reaction temperatures between 125°C and 250°C. A mass gain per cycle of 12 ng/(cm<sup>2</sup> cycle) was obtained from QCM measurements at 150°C and decreased at higher temperatures. QMS detected FSi(CH<sub>3</sub>)<sub>3</sub> as a reaction byproduct instead of HMDS at 150°C. LiF ALD showed self-limiting behavior. Ex situ measurements using X-ray reflectivity (XRR) and spectroscopic ellipsometry (SE) showed a growth rate of 0.5-0.6 Å/cycle, in good agreement with the in situ QCM measurements.</div><div>ALD of lithium ion conducting (AlF3)(LiF)x alloys was also demonstrated using in situ QCM and in situ QMS at reaction temperatures at 150°C A mass gain per sequence of 22 ng/(cm<sup>2</sup> cycle) was obtained from QCM measurements at 150°C. Ex situ measurements using XRR and SE showed a linear growth rate of 0.9 Å/sequence, in good agreement with the in situ QCM measurements. Stoichiometry between AlF<sub>3</sub> and LiF by QCM experiment was calculated to 1:2.8. XPS showed LiF film consist of lithium and fluorine. XPS also showed (AlF<sub>3</sub>)(LiF)x alloy consists of aluminum, lithium and fluorine. Carbon, oxygen, and nitrogen impurities were both below the detection limit of XPS. Grazing incidence X-ray diffraction (GIXRD) observed that LiF and (AlF<sub>3</sub>)(LiF)<sub>x</sub> alloy film have crystalline structures. Inductively coupled plasma mass spectrometry (ICP-MS) and ionic chromatography revealed atomic ratio of Li:F=1:1.1 and Al:Li:F=1:2.7: 5.4 for (AlF<sub>3</sub>)(LiF)<sub>x</sub> alloy film. These atomic ratios were consistent with the calculation from QCM experiments. Finally, lithium ion conductivity (AlF<sub>3</sub>)(LiF)<sub>x</sub> alloy film was measured as σ = 7.5 × 10<sup>-6</sup> S/cm.</div>

Abnormal Microstructure Evolution Behaviors of Annealed Ag-Co Alloy Film on Flexible Polyimide Substrates

2020 ◽  
Author(s):  
Yuanjiang Lv ◽  
Xin Xin Lian ◽  
Haoliang Sun ◽  
Xiaoxue Huang ◽  
Guang xin Wang
Keyword(s):  
Microstructure Evolution ◽  
Alloy Film
Sign in / Sign up

Export Citation Format

Share Document