Comparisons of single-phase and two-phase models for numerical predictions of Al2O3/water nanofluids convective heat transfer

2020 ◽  
Vol 31 (7) ◽  
pp. 3050-3061
Author(s):  
Zhaoping Ying ◽  
Boshu He ◽  
Di He ◽  
Yucheng Kuang ◽  
Jie Ren ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Single Phase ◽  
Two Phase ◽  
Numerical Predictions ◽  
Phase Models

A comparative analysis on the single-phase and two-phase mixture models for calculation of ferrofluid convective heat transfer in the presence of a magnetic field: a numerical study

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Hamed Jafari ◽  
Mohammad Goharkhah ◽  
Alireza Mahdavi Nejad
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Single Phase ◽  
Numerical Study ◽  
Phase Method ◽  
Two Phase ◽  
Content Type ◽  
Phase Models

Purpose This paper aims to analyze the accuracy of the single and two-phase numerical methods for calculation of ferrofluid convective heat transfer in the presence of a magnetic field. The findings of current study are compared with previous single-phase numerical results and experimental data. Accordingly, the effect of various parameters including nanoparticles concentration, Reynolds number and magnetic field strength on the performance of the single and two-phase models are evaluated. Design/methodology/approach A two-phase mixture numerical study is carried out to investigate the influence of four U-shaped electromagnets on the hydrodynamic and thermal characteristics of Fe3O4/Water ferrofluid flowing inside a heated channel. Findings It is observed that the applied external magnetic field signifies the convective heat transfer from the channel surface, despite local reduction at a few locations. The maximum heat transfer enhancement is predicted as 23% and 25% using single and two-phase models, respectively. The difference between the results of the two models is mainly attributed to the slip velocity effect which is accounted for in the two-phase model. The magnetic field gradient leads to a significant increase in the slip velocity which in turn causes a slight difference in velocity and temperature profiles obtained by the single and two-phase models in the magnetic field region. According to percentage error calculation, the two-phase method is generally more accurate than the single-phase method. However, the percentage error of both models improves by decreasing either magnetic field intensity or Reynolds number. Originality/value For the first time in the literature, to the best of the authors’ knowledge, the current work analyzes the accuracy of the single and two phase numerical methods for calculation of ferrofluid convective heat transfer in the presence of a magnetic field.

Assessment of Single and Two-Phase Models for Nanofluid Flow at the Entrance Region of a Uniformly Heated Tube

2012 ◽  
Author(s):  
Sinan Goktepe ◽  
Kunt Atalik ◽  
Hakan Erturk
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Friction Factor ◽  
Convective Heat ◽  
Control Volume ◽  
Convective Heat Transfer Coefficient ◽  
Computational Cost ◽  
Nanofluid Flow ◽  
Two Phase ◽  
Phase Models

Hydrodynamic and thermal characteristics of Al2O3 – water nanofluid flow at entry region of a uniformly heated pipe are studied applying finite control volume method (FCV). Single phase and Eulerian-Eulerian two-phase models were used in modelling of nanofluid flow and heat transfer. The two methods are evaluated by comparing predicted convective heat transfer coefficients and friction factor with experimental results from literature. Solutions with two different velocity pressure coupling algorithms, Full Multiphase Coupled, and Phase Coupled Semi-Implicit Method for Pressure Linked Equations are also compared in terms of accuracy and computational cost. Two-phase model predicts convective heat transfer coefficient and friction factor more accurately at the entry region. Moreover, computational cost can be reduced by implementing Full Multiphase Coupled scheme.

Comparison of Single and Two-Phase Models for the Study of Mixed Convection Flows With Nanofluids

2010 ◽  
Author(s):  
Mahmood Akbari ◽  
Amin Behzadmehr ◽  
Nicolas Galanis
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Mixed Convection ◽  
Single Phase ◽  
Volume Fraction ◽  
Solid Particles ◽  
Two Phase ◽  
Prediction Ability ◽  
Numerical Predictions ◽  
Phase Models

The single phase and three different two phase models (Volume of fluid, Mixture and Eulerian) are used to analyse laminar mixed convection flow of Al2O3-water nanofluids in a horizontal tube, in order to evaluate their prediction ability. The flow is considered steady and developing. The fluid’s physical properties are temperature dependent whereas those of the solid particles are constant. A uniform heat flux is applied at the fluid-solid interface. Two different Reynolds numbers and three different volume fractions have been considered. The governing three-dimensional partial differential equations are elliptical in all directions and coupled. Predicted convective heat transfer coefficients, velocity, and temperature profiles, as well as secondary flow’s velocity vectors and temperature contours are compared at different axial positions. To validate the comparisons and verify the accuracy of the results, the numerical predictions are compared with corresponding experimental data. There are essentially no differences between the predictions of the two-phase models; however their results are significantly different from those of the single-phase approach. Two-phase model results are closer to the experimental data, but they show an unrealistic increase in heat transfer for small changes of the particle volume fraction. Hydrodynamically, the two-phase and single-phase approaches perform almost the same but their thermal predictions are quite different.

A New Thermodynamic and Heat Transfer Model for Nanolubricants and Refrigerant Heat Transfer Processes in Smooth Copper Tubes

2020 ◽  
Vol 142 (8) ◽  
Author(s):  
Pratik S. Deokar ◽  
Lorenzo Cremaschi ◽  
Andrea A. M. Bigi
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Single Phase ◽  
Flow Boiling ◽  
Heat Transfer Model ◽  
Forced Flow ◽  
Transfer Model ◽  
Phase Flow ◽  
Two Phase

Abstract In air conditioning systems, lubricating oil leaves the compressor and circulates through the other system components. This lubricant acts as a contaminant affecting heat transfer in heat exchangers. The literature indicated that mixtures of refrigerants and nanolubricants, that is, nanoparticles dispersed in the lubricant oils, have potentials to augment heat transfer exchange effectiveness. However, the nanoparticle mechanisms leading to such heat transfer changes are still unclear and not well included in the models. In this work, an existing single-phase forced flow convective heat transfer model, originally developed for water-based nanofluids, was modified to include the effects of diffusion and mass balance of different shape nanoparticles within the laminar sublayer and turbulent layer of the flow. A new physics-based superposition heat transfer model for saturated two-phase flow boiling of refrigerant and nanolubricants was also developed by integrating the modified forced flow convective heat transfer model and a semi-empirical pool boiling model for nanolubricants. The new model included the several physical effects that influenced heat transfer, such as slip mechanisms at the nanoparticles and base fluid interface and its influence on the laminar sublayer thickness, momentum transfer from the nanoparticles to the growing bubbles, and formation of lubricant excess concentration at the tube surface and its influence on bubble growth and tube wetting. The new model was validated for single-phase convective heat transfer and two-phase flow boiling of refrigerant R410A with two nanolubricants, having nonspherical ZnO nanoparticles and spherical Al2O3 nanoparticles.

Single- and Two-Phase Convective Heat Transfer From Smooth and Enhanced Microelectronic Heat Sources in a Rectangular Channel

1989 ◽  
Vol 111 (4) ◽  
pp. 1045-1052 ◽  
Author(s):  
D. E. Maddox ◽  
I. Mudawar
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Source ◽  
Convective Heat Transfer ◽  
Forced Convection ◽  
Convective Heat ◽  
Single Phase ◽  
Rectangular Channel ◽  
Heat Sources ◽  
Two Phase

Experiments have been performed to assess the feasibility of cooling microelectronic components by means of single-phase and two-phase forced convection. Tests were conducted using a single heat source flush mounted to one wall of a vertical rectangular channel. An inert fluorocarbon liquid (FC-72) was circulated upward through the channel at velocities up to 4.1 m/s and with subcooling up to 46°C. The simulated microelectronic heat sources tested in this study include a smooth surface and three low-profile microstud surfaces of varying stud height, each having a base area of 12.7×12.7 mm2. Correlations were developed for the single-phase convective heat transfer coefficient over the Reynolds number range from 2800 to 1.5 × 105, where Reynolds number is based on the length of the heater. The results demonstrate that the low thermal resistances required for cooling of microelectronic heat sources may be achieved with single-phase forced convection by using high fluid velocity coupled with surface enhancement. Experiments were also performed to understand better the parametric trends of boiling heat transfer from the simulated microelectronic heat source. It was found that increased velocity and subcooling and the use of microstud surfaces enhance nucleate boiling, increase the critical heat flux, and reduce the magnitude of temperature overshoot upon the inception of nucleation.

Sign in / Sign up

Export Citation Format

Share Document