Enhanced osseointegration of Ti6Al4V ELI screws built-up by electron beam additive manufacturing: An experimental study in rabbits

2020 ◽  
Vol 508 ◽  
pp. 145160 ◽  
Author(s):  
Byoung-Soo Lee ◽  
Hae-Jin Lee ◽  
Kang-Sik Lee ◽  
Hyung Giun Kim ◽  
Gun-Hee Kim ◽  
...  
Keyword(s):  
Experimental Study ◽  
Electron Beam ◽  
Additive Manufacturing

A Procedure for Determining the Operating Modes of Electron Beam Wire Feed Layer-Wise Deposition for Additive Manufacturing

Vestnik MEI ◽  
2017 ◽  
pp. 8-14 ◽  
Author(s):  
Aleksandr V. Gudenko ◽  
◽  
Viktor К. Dragunov ◽  
Andrey Р. Sliva ◽  
◽  
...  
Keyword(s):  
Electron Beam ◽  
Additive Manufacturing ◽  
Operating Modes ◽  
Wire Feed

scholarly journals Contactless temperature measurement in wire-based electron beam additive manufacturing Ti-6Al-4V

2021 ◽  
Author(s):  
F. Pixner ◽  
R. Buzolin ◽  
S. Schönfelder ◽  
D. Theuermann ◽  
F. Warchomicka ◽  
...  
Keyword(s):  
Electron Beam ◽  
Additive Manufacturing ◽  
Thermal Imaging ◽  
Temperature Profiles ◽  
Layer By Layer ◽  
Thermal Cycles ◽  
Cooling Rates ◽  
Geometric Boundary ◽  
Microstructural Characterisation ◽  
Local Misorientation

AbstractThe complex thermal cycles and temperature distributions observed in additive manufacturing (AM) are of particular interest as these define the microstructure and the associated properties of the part being built. Due to the intrinsic, layer-by-layer material stacking performed, contact methods to measure temperature are not suitable, and contactless methods need to be considered. Contactless infrared irradiation techniques were applied by carrying out thermal imaging and point measurement methods using pyrometers to determine the spatial and temporal temperature distribution in wire-based electron beam AM. Due to the vacuum, additional challenges such as element evaporation must be overcome and additional shielding measures were taken to avoid interference with the contactless techniques. The emissivities were calibrated by thermocouple readings and geometric boundary conditions. Thermal cycles and temperature profiles were recorded during deposition; the temperature gradients are described and the associated temperature transients are derived. In the temperature range of the α+β field, the cooling rates fall within the range of 180 to 350 °C/s, and the microstructural characterisation indicates an associated expected transformation of β→α'+α with corresponding cooling rates. Fine acicular α and α’ formed and local misorientation was observed within α as a result of the temperature gradient and the formation of the α’.

scholarly journals Directionally-Dependent Mechanical Properties of Ti6Al4V Manufactured by Electron Beam Melting (EBM) and Selective Laser Melting (SLM)

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3603
Author(s):  
Tim Pasang ◽  
Benny Tavlovich ◽  
Omry Yannay ◽  
Ben Jakson ◽  
Mike Fry ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Tensile Strength ◽  
Electron Beam ◽  
Additive Manufacturing ◽  
Selective Laser Melting ◽  
Electron Beam Melting ◽  
Rolling Direction ◽  
Laser Melting ◽  
Plate Rolling

An investigation of mechanical properties of Ti6Al4V produced by additive manufacturing (AM) in the as-printed condition have been conducted and compared with wrought alloys. The AM samples were built by Selective Laser Melting (SLM) and Electron Beam Melting (EBM) in 0°, 45° and 90°—relative to horizontal direction. Similarly, the wrought samples were also cut and tested in the same directions relative to the plate rolling direction. The microstructures of the samples were significantly different on all samples. α′ martensite was observed on the SLM, acicular α on EBM and combination of both on the wrought alloy. EBM samples had higher surface roughness (Ra) compared with both SLM and wrought alloy. SLM samples were comparatively harder than wrought alloy and EBM. Tensile strength of the wrought alloy was higher in all directions except for 45°, where SLM samples showed higher strength than both EBM and wrought alloy on that direction. The ductility of the wrought alloy was consistently higher than both SLM and EBM indicated by clear necking feature on the wrought alloy samples. Dimples were observed on all fracture surfaces.

Peculiarities of tensile deformation and fracture of high-nitrogen steel obtained by electron beam additive manufacturing

2020 ◽  
Author(s):  
Sergey V. Astafurov ◽  
Elena G. Astafurova ◽  
Kseniya A. Reunova ◽  
Evgenii V. Melnikov ◽  
Marina Yu. Panchenko ◽  
...  
Keyword(s):  
Electron Beam ◽  
Additive Manufacturing ◽  
Tensile Deformation ◽  
High Nitrogen Steel ◽  
High Nitrogen ◽  
Deformation And Fracture ◽  
Nitrogen Steel
Sign in / Sign up

Export Citation Format

Share Document