One-step method for fabrication of bioinspired hierarchical superhydrophobic surface with robust stability

2019 ◽  
Vol 473 ◽  
pp. 493-499 ◽  
Author(s):  
Dongguang Zhang ◽  
Linghan Li ◽  
Yali Wu ◽  
Bin Zhu ◽  
Honglie Song
Keyword(s):  
Robust Stability ◽  
Superhydrophobic Surface ◽  
Step Method ◽  
One Step

scholarly journals One-step fabrication of soft calcium superhydrophobic surfaces by a simple electrodeposition process

RSC Advances ◽  
2022 ◽  
Vol 12 (1) ◽  
pp. 297-308
Author(s):  
Zhi Chen ◽  
Yongbo Hu ◽  
Xu He ◽  
Yihao Xu ◽  
Xuesong Liu ◽  
...  
Keyword(s):  
Formation Process ◽  
Superhydrophobic Surface ◽  
Surface Preparation ◽  
Superhydrophobic Surfaces ◽  
Water Droplets ◽  
Step Method ◽  
Electrodeposition Process ◽  
Pressing Force ◽  
One Step

We investigated a one-step method for calcium superhydrophobic surface preparation and researched the formation process of loose, flower-like microstructures. Also, we found that the pressing force strongly impacts the dynamics of water droplets.

One-step method for fabrication of biomimetic superhydrophobic surface on aluminum alloy

2015 ◽  
Vol 466 ◽  
pp. 125-131 ◽  
Author(s):  
Yan Liu ◽  
Jindan Liu ◽  
Shuyi Li ◽  
Yaming Wang ◽  
Zhiwu Han ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Superhydrophobic Surface ◽  
Step Method ◽  
One Step

Effect of Dynamic Crosslinking on Mechanical Properties of PP/EPDM Blends

1993 ◽  
Vol 58 (11) ◽  
pp. 2642-2650 ◽  
Author(s):  
Zdeněk Kruliš ◽  
Ivan Fortelný ◽  
Josef Kovář
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Shear Modulus ◽  
High Impact ◽  
Necessary Condition ◽  
Step Method ◽  
Melt Mixing ◽  
One Step ◽  
High Impact Strength ◽  
Dynamic Curing

The effect of dynamic curing of PP/EPDM blends with sulfur and thiuram disulfide systems on their mechanical properties was studied. The results were interpreted using the knowledge of the formation of phase structure in the blends during their melt mixing. It was shown, that a sufficiently slow curing reaction is necessary if a high impact strength is to be obtained. Only in such case, a fine and homogeneous dispersion of elastomer can be formed, which is the necessary condition for high impact strength of the blend. Using an inhibitor of curing in the system and a one-step method of dynamic curing leads to an increase in impact strength of blends. From the comparison of shear modulus and impact strength values, it follows that, at the stiffness, the dynamically cured blends have higher impact strength than the uncured ones.

Bismuth particles imbedded degradable nanohydrogel prepared by one-step method for tumor dual-mode imaging and chemo-photothermal combined therapy

2019 ◽  
Vol 375 ◽  
pp. 122000 ◽  
Author(s):  
Yang Xuan ◽  
Xian-Lin Song ◽  
Xiao-Quan Yang ◽  
Ruo-Yun Zhang ◽  
Zi-Yu Song ◽  
...  
Keyword(s):  
Combined Therapy ◽  
Dual Mode ◽  
Step Method ◽  
One Step

scholarly journals Bio-Based Polyurethane Networks Derived from Liquefied Sawdust

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3138
Author(s):  
Kamila Gosz ◽  
Agnieszka Tercjak ◽  
Adam Olszewski ◽  
Józef Haponiuk ◽  
Łukasz Piszczyk
Keyword(s):  
Biomass Conversion ◽  
Structural Features ◽  
Mechanical Analysis ◽  
Process Efficiency ◽  
Hydroxyl Number ◽  
Step Method ◽  
One Step ◽  
Liquefaction Process ◽  
The Fourier Transform ◽  
Liquefaction Temperature

The utilization of forestry waste resources in the production of polyurethane resins is a promising green alternative to the use of unsustainable resources. Liquefaction of wood-based biomass gives polyols with properties depending on the reagents used. In this article, the liquefaction of forestry wastes, including sawdust, in solvents such as glycerol and polyethylene glycol was investigated. The liquefaction process was carried out at temperatures of 120, 150, and 170 °C. The resulting bio-polyols were analyzed for process efficiency, hydroxyl number, water content, viscosity, and structural features using the Fourier transform infrared spectroscopy (FTIR). The optimum liquefaction temperature was 150 °C and the time of 6 h. Comprehensive analysis of polyol properties shows high biomass conversion and hydroxyl number in the range of 238–815 mg KOH/g. This may indicate that bio-polyols may be used as a potential substitute for petrochemical polyols. During polyurethane synthesis, materials with more than 80 wt% of bio-polyol were obtained. The materials were obtained by a one-step method by hot-pressing for 15 min at 100 °C and a pressure of 5 MPa with an NCO:OH ratio of 1:1 and 1.2:1. Dynamical-mechanical analysis (DMA) showed a high modulus of elasticity in the range of 62–839 MPa which depends on the reaction conditions.

Discussion on Repair Method of Concrete Highway Pavement

2013 ◽  
Vol 321-324 ◽  
pp. 209-212
Author(s):  
Chun Yan Xia
Keyword(s):  
Mechanical Properties ◽  
Preparation Program ◽  
Step Method ◽  
Concrete Technology ◽  
Concrete Material ◽  
Repair Method ◽  
Ordinary Concrete ◽  
One Step ◽  
Highway Pavement

nfluences on properties of the concrete highway pavement were analyzed in this paper, and the optimal formulation materials were gotten to use in the repair of used-broken cement blocks in the experiment. Polyurethane concrete material was prepared, combing the ordinary concrete technology with one-step method of the synthesis of polyurethane hard bubble, and then its mechanical properties of the relevant parameters were measured to determine the optimal preparation program. The results show that the polyurethane concrete also has sufficiently good mechanical properties while it has the characteristic of fast patching.

A novel, one-step method for the conversion of primary alcohols into carbamate-protected amines

2002 ◽  
Vol 43 (21) ◽  
pp. 3887-3890 ◽  
Author(s):  
Michael R. Wood ◽  
June Y. Kim ◽  
Kathy M. Books
Keyword(s):  
Primary Alcohols ◽  
Step Method ◽  
One Step
Sign in / Sign up

Export Citation Format

Share Document