Long-term osseointegration of 3D printed CoCr constructs with an interconnected open-pore architecture prepared by electron beam melting

2016 ◽  
Vol 36 ◽  
pp. 296-309 ◽  
Author(s):  
Furqan A. Shah ◽  
Omar Omar ◽  
Felicia Suska ◽  
Anders Snis ◽  
Aleksandar Matic ◽  
...  
Keyword(s):  
Electron Beam ◽  
Electron Beam Melting ◽  
Pore Architecture ◽  
3D Printed

scholarly journals Long-term osseointegration of 3D printed CoCr implants with an interconnected open-pore architecture

2016 ◽  
Vol 4 ◽  
Author(s):  
Shah Furqan ◽  
Omar Omar ◽  
Suska Felicia ◽  
Snis Anders ◽  
Emanuelsson Lena ◽  
...  
Keyword(s):  
Pore Architecture ◽  
3D Printed

Tribological Properties of Three-Dimensionally Printed Ti–6Al–4V Material Via Electron Beam Melting Process Tested Against 100Cr6 Steel Without and With Hank's Solution

2018 ◽  
Vol 140 (6) ◽  
Author(s):  
N. W. Khun ◽  
W. Q. Toh ◽  
X. P. Tan ◽  
E. Liu ◽  
S. B. Tor
Keyword(s):  
Electron Beam ◽  
Tribological Properties ◽  
Electron Beam Melting ◽  
Surface Hardness ◽  
Melting Process ◽  
Martensitic Structure ◽  
Mechanical And Tribological Properties ◽  
3D Printed ◽  
Electron Beam Melting Process ◽  
Hank’S Solution

Three-dimensionally (3D) printed Ti–6Al–4V (Ti64) samples via an electron beam melting (EBM) process were developed to investigate their microstructure and mechanical and tribological properties in comparison with those of commercial Ti64 samples. The 3D-printed Ti64 samples had a heavily twinned and acicular martensitic structure that was responsible for their higher surface hardness than that of the commercial Ti64 samples. The 3D-printed Ti64 samples tested against a 100Cr6 steel counter ball without and with Hank's solution had a higher wear resistance associated with their higher surface hardness than the commercial Ti64 samples. The use of Hank's solution during sliding reduced the wear of the both Ti64 samples as a result of the lubricating effect of the solution. It could be concluded that the 3D-printed Ti64 samples in this study had comparable mechanical and tribological properties to those of the commercial Ti64 samples.

Assessing Porosity in Selective Electron Beam Melting Manufactured Ti–6Al–4V by Nonlinear Impact Modulation Spectroscopy

2020 ◽  
Vol 39 (4) ◽  
Author(s):  
Jan Kober ◽  
Alexander Kirchner ◽  
Alena Kruisova ◽  
Milan Chlada ◽  
Sigrun Hirsekorn ◽  
...  
Keyword(s):  
Electron Beam ◽  
Electron Beam Melting ◽  
Modulation Spectroscopy ◽  
Selective Electron Beam Melting

scholarly journals A millifluidic chip for cultivation of fish embryos and toxicity testing fabricated by 3D printing technology

RSC Advances ◽  
2021 ◽  
Vol 11 (33) ◽  
pp. 20507-20518
Author(s):  
Petr Panuška ◽  
Zuzana Nejedlá ◽  
Jiří Smejkal ◽  
Petr Aubrecht ◽  
Michaela Liegertová ◽  
...  
Keyword(s):  
3D Printing ◽  
Toxicity Testing ◽  
Toxicity Screening ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Fish Embryos ◽  
3D Printed ◽  
Novel Design

A novel design of 3D printed zebrafish millifluidic system for embryonic long-term cultivation and toxicity screening has been developed. The chip unit provides 24 cultivation chambers and a selective individual embryo removal functionality.

Processing of Tungsten Through Electron Beam Melting

2021 ◽  
pp. 153041
Author(s):  
Elizabeth A.I. Ellis ◽  
Michael A. Sprayberry ◽  
Christopher Ledford ◽  
Jameson P. Hankwitz ◽  
Michael M. Kirka ◽  
...  
Keyword(s):  
Electron Beam ◽  
Electron Beam Melting
Sign in / Sign up

Export Citation Format

Share Document