Rigidity and resistance of larval- and adult schistosomes-medium interface

2014 ◽  
Vol 446 (1) ◽  
pp. 255-260 ◽  
Author(s):  
Federica Migliardo ◽  
Hatem Tallima ◽  
Rashika El Ridi
Keyword(s):  
Medium Interface

Fatty Acid Metabolism in Human Keratinocytes Cultivated at an Air-Medium Interface

1989 ◽  
Vol 92 (2) ◽  
pp. 196-202 ◽  
Author(s):  
Nanna Y. Schürer ◽  
Daniel J. Monger ◽  
Mara Hincenbergs ◽  
Mary L. Williams
Keyword(s):  
Fatty Acid ◽  
Fatty Acid Metabolism ◽  
Acid Metabolism ◽  
Human Keratinocytes ◽  
Medium Interface ◽  
Air Medium

Pseudo interface waves observed at the fluid/porous-medium interface. A comparison of two methods

2011 ◽  
Vol 129 (5) ◽  
pp. 2912-2922 ◽  
Author(s):  
K. N. van Dalen ◽  
G. G. Drijkoningen ◽  
D. M. J. Smeulders
Keyword(s):  
Porous Medium ◽  
Interface Waves ◽  
Medium Interface

scholarly journals Numerical Analysis for the Progressive Failure of Binary-Medium Interface under Shearing

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Rihong Cao ◽  
Wenyu Tang ◽  
Hang Lin ◽  
Xiang Fan
Keyword(s):  
Shear Strength ◽  
Bond Strength ◽  
Normal Stress ◽  
Strength Ratio ◽  
Normal Stresses ◽  
Stress Increase ◽  
Tensile Cracks ◽  
Medium Interface ◽  
High Bond ◽  
High Bond Strength

Binary-medium specimens were fabricated using the particle flow code, and the shear strength, dilatancy, and failure behavior of the binary-medium specimens with different bond strength ratios (0.25, 0.5, 0.75, and 1.0) under different normal stresses were studied. Numerical results show that the bond strength ratio and normal stresses considerably influence the shear strengths of binary-medium interface. Shear strength increases as the bond strength ratio and normal stress increase. The dilation of interfaces with high bond strength ratios is more evident than those of interfaces with lower bond strength ratios, and the curves for the high bond strength ratio exhibit remarkable fluctuations during the residual stage. At increased normal stress and bond strength ratio, the peak dilation angle shows decreasing and increasing trends successively. In this study, the specimens exhibited three kinds of failure modes. In mode II, the sawtooth experienced shear failure, but some tensile cracks appeared on the interface of the binary-medium. In mode III, no sawtooth was cut off, indicating tensile failure on the interface. At a low bond strength ratio, damage or failure is mostly concentrated in the upper part of the model. Failure parts gradually transfer to the lower part of the model when the bond strength ratio and normal stress increase. Furthermore, evident tensile cracks occur on the interface. When the bond strength ratio reaches 1.0, the failure mode of the specimen gradually transforms from sheared-off failure to chip-off failure. The number of microcracks in the specimens indicates that the lower the bond strength ratio, the more severe the damage on the specimens.

Role of the Solid–Aqueous Medium Interface in Transferring Light-Induced Excitation of Silicon

2019 ◽  
Vol 64 (9) ◽  
pp. 1350-1356
Author(s):  
D. I. Tetel’baum ◽  
V. S. Tulovchikov ◽  
Yu. A. Mendeleva ◽  
E. V. Kuril’chik ◽  
A. A. Nikolskaya ◽  
...  
Keyword(s):  
Aqueous Medium ◽  
Medium Interface
Sign in / Sign up

Export Citation Format

Share Document