Under-Deposit Corrosion of Carbon Steel Beneath Full Coverage of CaCO3 Deposit Layer under Different Atmospheres

2021 ◽  
Author(s):  
Lin Pang ◽  
Zhengbin Wang ◽  
Wilfred Emori ◽  
Yugui Zheng
Keyword(s):  
Carbon Steel ◽  
Full Coverage ◽  
Deposit Layer

Direct Observation of Heat Exchanger Deposits by Cross Sectioning

1967 ◽  
Vol 25 ◽  
pp. 364-365
Author(s):  
R. W. Anderson ◽  
D. L. Senecal
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Heat Exchanger ◽  
Direct Observation ◽  
Cross Sections ◽  
Preparation Method ◽  
Specimen Preparation ◽  
Flowing Water ◽  
Transmission Electron ◽  
Deposit Layer

A problem was presented to observe the packing densities of deposits of sub-micron corrosion product particles. The deposits were 5-100 mils thick and had formed on the inside surfaces of 3/8 inch diameter Zircaloy-2 heat exchanger tubes. The particles were iron oxides deposited from flowing water and consequently were only weakly bonded. Particular care was required during handling to preserve the original formations of the deposits. The specimen preparation method described below allowed direct observation of cross sections of the deposit layers by transmission electron microscopy.The specimens were short sections of the tubes (about 3 inches long) that were carefully cut from the systems. The insides of the tube sections were first coated with a thin layer of a fluid epoxy resin by dipping. This coating served to impregnate the deposit layer as well as to protect the layer if subsequent handling were required.

Pyrolytic carbon filaments and associated catalytic particles formed in steel tubes

1984 ◽  
Vol 42 ◽  
pp. 662-663
Author(s):  
Y. L. Chen ◽  
J. R. Bradley
Keyword(s):  
Stainless Steel ◽  
Carbon Steel ◽  
Catalyst Particle ◽  
Pyrolytic Carbon ◽  
Plain Carbon Steel ◽  
304 Stainless Steel ◽  
Hydrocarbon Gases ◽  
Steel Tubes ◽  
Filamentous Carbon ◽  
Carbon Filaments

Considerable effort has been directed toward an improved understanding of the production of the strong and stiff ∼ 1-20 μm diameter pyrolytic carbon fibers of the type reported by Koyama and, more recently, by Tibbetts. These macroscopic fibers are produced when pyrolytic carbon filaments (∼ 0.1 μm or less in diameter) are thickened by deposition of carbon during thermal decomposition of hydrocarbon gases. Each such precursor filament normally lengthens in association with an attached catalyst particle. The subject of filamentous carbon formation and much of the work on characterization of the catalyst particles have been reviewed thoroughly by Baker and Harris. However, identification of the catalyst particles remains a problem of continuing interest. The purpose of this work was to characterize the microstructure of the pyrolytic carbon filaments and the catalyst particles formed inside stainless steel and plain carbon steel tubes. For the present study, natural gas (∼; 97 % methane) was passed through type 304 stainless steel and SAE 1020 plain carbon steel tubes at 1240°K.

Internal friction in a martensitic high-carbon steel

2001 ◽  
Vol 81 (12) ◽  
pp. 2797-2808
Author(s):  
Rustem Bagramov, Daniele Mari, Willy Benoi
Keyword(s):  
Carbon Steel ◽  
Internal Friction ◽  
High Carbon Steel ◽  
High Carbon

Development of trimming technology for hot rolled ultra-low carbon steel

1993 ◽  
Vol 90 (7-8) ◽  
pp. 917-922
Author(s):  
Y. Matsuda ◽  
M. Nishino ◽  
J. Ikeda
Keyword(s):  
Carbon Steel ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Ultra Low Carbon Steel ◽  
Hot Rolled

INFLUENCE THE QUENCHING AND TEMPERING ON THE MICROSTRUCTURE, MECHANICAL PROPERTIES AND SURFACE ROUGHNESS, OF MEDIUM CARBON STEEL

2018 ◽  
Vol 18 (1) ◽  
pp. 125-135
Author(s):  
Sattar H A Alfatlawi
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Surface Roughness ◽  
Carbon Steel ◽  
Cold Water ◽  
Medium Carbon Steel ◽  
Medium Carbon ◽  
Heating And Cooling ◽  
Treatment Processes ◽  
Quenching And Tempering

One of ways to improve properties of materials without changing the product shape toobtain the desired engineering applications is heating and cooling under effect of controlledsequence of heat treatment. The main aim of this study was to investigate the effect ofheating and cooling on the surface roughness, microstructure and some selected propertiessuch as the hardness and impact strength of Medium Carbon Steel which treated at differenttypes of heat treatment processes. Heat treatment achieved in this work was respectively,heating, quenching and tempering. The specimens were heated to 850°C and left for 45minutes inside the furnace as a holding time at that temperature, then quenching process wasperformed in four types of quenching media (still air, cold water (2°C), oil and polymersolution), respectively. Thereafter, the samples were tempered at 200°C, 400°C, and 600°Cwith one hour as a soaking time for each temperature, then were all cooled by still air. Whenthe heat treatment process was completed, the surface roughness, hardness, impact strengthand microstructure tests were performed. The results showed a change and clearimprovement of surface roughness, mechanical properties and microstructure afterquenching was achieved, as well as the change that took place due to the increasingtoughness and ductility by reducing of brittleness of samples.

Commercial aqueous additives as used eco-friendly corrosion inhibitors for carbon steel in natural seawater

2020 ◽  
Vol 65 (1) ◽  
pp. 77-82
Author(s):  
Simona CAPRARESCU ◽  
◽  
Violeta PURCAR ◽  
Cristina MODROGAN ◽  
◽  
...  
Keyword(s):  
Carbon Steel ◽  
Corrosion Inhibitors ◽  
Natural Seawater

Effects of Particle Size Distribution on Corrosion Rate of Carbon Steel in Soil

2020 ◽  
Vol 69 (4) ◽  
pp. 102-106
Author(s):  
Shota Ohki ◽  
Shingo Mineta ◽  
Mamoru Mizunuma ◽  
Soichi Oka ◽  
Masayuki Tsuda
Keyword(s):  
Particle Size ◽  
Carbon Steel ◽  
Corrosion Rate ◽  
Particle Size Distribution ◽  
Size Distribution
Sign in / Sign up

Export Citation Format

Share Document