Finite difference simulation and experimental investigation: effects of physical synergetic properties of nanoparticles on temperature distribution and surface integrity of workpiece in nanofluid MQL grinding process

2017 ◽  
Vol 95 (5-8) ◽  
pp. 2661-2679 ◽  
Author(s):  
Mohammadreza Shabgard ◽  
Mirsadegh Seyedzavvar ◽  
Mousa Mohammadpourfard ◽  
Mehran Mahboubkhah
Keyword(s):  
Experimental Investigation ◽  
Temperature Distribution ◽  
Finite Difference ◽  
Surface Integrity ◽  
Grinding Process ◽  
Mql Grinding

Study on Edge Contact Area and Surface Integrity of Workpiece in Point Grinding Process

2009 ◽  
Vol 407-408 ◽  
pp. 577-581
Author(s):  
Shi Chao Xiu ◽  
Zhi Jie Geng ◽  
Guang Qi Cai
Keyword(s):  
Surface Integrity ◽  
Contact Area ◽  
High Speed ◽  
Ground Surface ◽  
Depth Of Cut ◽  
Grinding Wheel ◽  
Grinding Process ◽  
Edge Contact ◽  
Cylindrical Grinding ◽  
Theoretic Foundations

During cylindrical grinding process, the geometric configuration and size of the edge contact area between the grinding wheel and workpiece have the heavy effects on the workpiece surface integrity. In consideration of the differences between the point grinding and the conventional high speed cylindrical grinding, the geometric and mathematic models of the edge contact area in point grinding were established. Based on the models, the numerical simulation for the edge contact area was performed. By means of the point grinding experiment, the effect mechanism of the edge contact area on the ground surface integrity was investigated. These will offer the applied theoretic foundations for optimizing the point grinding angles, depth of cut, wheel and workpiece speed, geometrical configuration and size of CBN wheel and some other grinding parameters in point grinding process.

Experimental Investigation of Microcutting Mechanisms in Marble Grinding

2009 ◽  
Vol 131 (6) ◽  
Author(s):  
LJ. Tanovic ◽  
P. Bojanic ◽  
R. Puzovic ◽  
S. Klimenko
Keyword(s):  
Experimental Study ◽  
Experimental Investigation ◽  
Cutting Force ◽  
Surface Finish ◽  
Normal Component ◽  
Natural Material ◽  
Grinding Process ◽  
Force Component ◽  
Diamond Grain

This paper offers an experimental study of the microcutting mechanisms in marble grinding to aid the optimization of the marble grinding process. The necessity for investigating these mechanisms is dictated by the increased use of marble in many applications and the fact that grinding and polishing processes are the dominant technologies used to meet surface finish requirements in this natural material. The experiments are aimed at the determination of the normal component of the cutting force and of the grain traces in microcutting with a single diamond grain. The investigations carried out make provisions for establishing critical grain penetration and cutting depths and allow the prediction of the normal cutting force component as a function of grain penetration speed and depth.

Einfluss der Abrichtgrößen beim Schleifen*/Influence of dressing parameters on the grinding process - Systematic research of dressing parameters on workpiece roughness and surface integrity

2016 ◽  
Vol 106 (01-02) ◽  
pp. 44-50
Author(s):  
T. Lierse ◽  
B. Karpuschewski ◽  
T. R. Kaul
Keyword(s):  
Aluminum Oxide ◽  
Surface Integrity ◽  
Cvd Diamond ◽  
Grinding Wheel ◽  
Systematic Research ◽  
Grinding Process ◽  
Wheel Topography ◽  
Grinding Wheel Topography

Dieser Beitrag zeigt, dass die durch die Abrichtparameter erzeugte Schleifscheibentopographie nicht nur die Oberflächengüte des Werkstücks, sondern auch dessen Eigenspannungszustand in der Werkstückrandzone in weiten Grenzen verändert. Die Untersuchungen zum Abrichten von Korundschleifscheiben mit einer CVD-Diamantformrolle stellen den Zusammenhang zwischen dem Abrichten unterschiedlicher Schleifscheiben zur Bauteilqualität in Form der Oberflächenrautiefe und randzonennahen Eigenspannungen her.   The quality of the workpiece rim is changed by every grinding process. The grinding wheel topography created by the dressing process has not only influence on the workpiece roughness but also on the surface integrity. The pointed research using aluminum oxide abrasive wheels dressed by CVD diamond dressing discs shows a correlation between the dressing parameters, the workpiece roughness and the surface integrity.

scholarly journals Peak Temperature Correlation and Temperature Distribution during Joining of AZ80A Mg Alloy by FSW – A Numerical and Experimental Investigation

2020 ◽  
Vol 66 (6) ◽  
pp. 395-407 ◽  
Author(s):  
p Sevvel ◽  
S.D. Dhanesh Babu ◽  
R. Senthil Kumar
Keyword(s):  
Experimental Investigation ◽  
Temperature Distribution ◽  
Quadratic Equation ◽  
Peak Temperature ◽  
Mg Alloy ◽  
Element Analysis ◽  
Temperature Correlation ◽  
Friction Stir ◽  
Az80a Mg Alloy ◽  
Experimental Values

A quadratic equation has been developed based on experimental measurements to estimate the peak temperature in the friction stir welding (FSW) process during the joining of AZ80A Mg alloys. The numerical simulation of the FSW process was performed by employing COMSOL software to predict and calculate the distribution of temperature on the various regions of the parent metal and the welded joints. The predicted and finite element analysis (FEA) simulating the results of the distribution of peak temperatures were found to be consistent with the experimental values. In addition to this, a parametric experimental investigation was conducted to identify the most influential process parameter that plays a significant role in the peak temperature distribution during FSW of AZ80A Mg alloy. Linear contributions by the input process parameters of FSW, namely, traversing speed, rotating tool speed and axial force on the peak temperature were observed to be 32.82 %, 41.65 % and 21.76 %, respectively.

Sign in / Sign up

Export Citation Format

Share Document