scholarly journals A facile chemical screening method for the detection of stress corrosion cracking in 9 carat gold alloys

Gold Bulletin ◽  
2009 ◽  
Vol 42 (3) ◽  
pp. 209-214 ◽  
Author(s):  
B. Neumeyer ◽  
John Hensler ◽  
Anthony P. O’Mullane ◽  
Suresh K. Bhargava
Keyword(s):  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Screening Method ◽  
Corrosion Cracking ◽  
Gold Alloys ◽  
Carat Gold ◽  
Chemical Screening ◽  
Detection Of Stress

Stress corrosion cracking of 18 carat gold

2004 ◽  
Vol 46 (1) ◽  
pp. 1-4 ◽  
Author(s):  
G.S Duffó ◽  
S.B Farina ◽  
J.R Galvele
Keyword(s):  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Corrosion Cracking ◽  
Carat Gold

Acoustic detection of stress-corrosion cracking of nitrogen austenitic steels

2014 ◽  
Vol 115 (6) ◽  
pp. 586-599 ◽  
Author(s):  
Yu. I. Filippov ◽  
V. V. Sagaradze ◽  
V. A. Zavalishin ◽  
N. L. Pecherkina ◽  
N. V. Kataeva ◽  
...  
Keyword(s):  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Corrosion Cracking ◽  
Austenitic Steels ◽  
Acoustic Detection ◽  
Detection Of Stress

Electron Metallography of Chemical Attack Upon Some Alloys Susceptible to Stress Corrosion Cracking

CORROSION ◽  
1963 ◽  
Vol 19 (11) ◽  
pp. 373t-389t ◽  
Author(s):  
H. W. PICKERING ◽  
P. R. SWANN
Keyword(s):  
Aluminum Alloys ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Corrosion Cracking ◽  
Surface Roughening ◽  
Gold Alloys ◽  
Atom Concentration ◽  
Chemical Attack ◽  
Copper Gold ◽  
Slip Planes

Abstract The microstructures of deformed copper-gold, copper-aluminum, copper-zinc and magnesium-aluminum alloys were examined by transmission electron microscopy. These specimens were further examined after exposure to solutions which do and do not cause stress corrosion cracking. Exposure to “cracking” solutions resulted in a localized pitting or tubular form of attack, whereas the solutions which did not produce cracking caused a uniform surface roughening. When thin-foil specimens were deformed within the corrosive environments, the tubular attack and the surface roughening were observed to be enhanced in the regions of heavy deformation. Observations also indicated that for all the alloys investigated, static dislocations did not initiate chemical attack. In general, the pitting or tubular type of attack may be initiated at grain boundaries, antiphase boundary junctions in ordered copper-gold alloys, at precipitates and the substructure of twins in magnesium-aluminum alloys and at other sites which could not be identified. It was concluded that compositional rather than physical disturbances initiate preferential chemical attack on the surface of the alloys studied. For copper-gold alloys the superficial chemical disturbance can be as small as a six-atom cluster. Rates of pitting greater than 0.4 cm/hr can be attained for copper-gold alloys, which compares well with stress corrosion crack velocities. In the discussion of these results a new mechanism for transgranular stress corrosion is presented. It is proposed that when susceptible alloys are exposed to stress corrosion cracking environments a mechanically weak, pitted structure is produced along active slip planes, and that ductile fracture occurs through this corroded material. The chemical activity of the slip planes, which are believed to initiate the pitting attack, is discussed in relation to (a) the type of surface slip structure found in alloys where cross slip is difficult, (b) increase in solute atom concentration at the crack tip through the mass transfer of solute atoms to the surface by planar groups of moving dislocations, and (c) segregation and precipitation on slip planes. It was found that very fine precipitates, which are either an intermediate magnesium-aluminum phase or Mg17Al12, formed on the basal planes of quenched magnesium-1 or 7 atomic percent aluminum (<0.001 percent Fe, Cu or Ni) alloys when aged at room temperature. The presence of these precipitates was associated with the transgranular stress corrosion susceptibility of these alloys.

Detection of Stress Corrosion Cracking by Direct-Current Potential Difference Method

2011 ◽  
Author(s):  
Naoya Tada ◽  
Makoto Uchida ◽  
Hiroki Maeda ◽  
Atsushi Hozuki
Keyword(s):  
Stress Corrosion ◽  
Direct Current ◽  
Stress Corrosion Cracking ◽  
Difference Method ◽  
Corrosion Cracking ◽  
Potential Difference ◽  
Measurement Results ◽  
Detection Of Stress ◽  
Metal Weld ◽  
Current Potential

Stress corrosion cracking (SCC) is one of serious damages occurred in power generating plants, petrochemical plants, and gas pipelines. However, it is not easy to detect and evaluate SCCs because their shapes are complex and they are usually initiated in the weldment composed of base metal, weld metal, and heat-affected zone. In this study, the direct-current potential difference method (DC-PDM) was applied to SCCs artificially introduced in plate specimens and the applicability of DC-PDM to their detection was discussed. It was found from the measurement results that the potential differences near SCC were higher than those away from SCC. This fact suggests that SCC is detectable by DC-PDM.

scholarly journals Remote detection of stress corrosion cracking: Surface composition and crack detection

2018 ◽  
Author(s):  
Cliff J. Lissenden ◽  
Igor Jovanovic ◽  
Arthur T. Motta ◽  
Xuan Xiao ◽  
Samuel Le Berre ◽  
...  
Keyword(s):  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Crack Detection ◽  
Surface Composition ◽  
Corrosion Cracking ◽  
Remote Detection ◽  
Detection Of Stress
Sign in / Sign up

Export Citation Format

Share Document