scholarly journals Erratum to: The determination of eigen-functions of a certain Sturm-Liouville equation and its application to problems of heat-transfer

1958 ◽  
Vol 7 (6) ◽  
pp. 478-478 ◽  
Author(s):  
S. N. Singh
Keyword(s):  
Heat Transfer ◽  
Liouville Equation ◽  
Sturm Liouville

INFLUENCE OF HEAT TREATMENT OF MOUNTAIN MASSIVE ON TEMPERATURE MODE OF GEOTHERMAL CIRCULATION SYSTEM

2018 ◽  
pp. 44-50
Author(s):  
Yu. P. Morozov
Keyword(s):  
Heat Transfer ◽  
Operating Time ◽  
Fluid Motion ◽  
Coolant Temperature ◽  
Circulation System ◽  
Thermal Processes ◽  
Temperature Mode ◽  
Heat Influx ◽  
Stationary Heat Transfer

Based on the solution of the problem of non-stationary heat transfer during fluid motion in underground permeable layers, dependence was obtained to determine the operating time of the geothermal circulation system in the regime of constant and falling temperatures. It has been established that for a thickness of the layer H <4 m, the influence of heat influxes at = 0.99 and = 0.5 is practically the same, but for a thickness of the layer H> 5 m, the influence of heat inflows depends significantly on temperature. At a thickness of the permeable formation H> 20 m, the heat transfer at = 0.99 has virtually no effect on the thermal processes in the permeable formation, but at = 0.5 the heat influx, depending on the speed of movement, can be from 50 to 90%. Only at H> 50 m, the effect of heat influx significantly decreases and amounts, depending on the filtration rate, from 50 to 10%. The thermal effect of the rock mass with its thickness of more than 10 m, the distance between the discharge circuit and operation, as well as the speed of the coolant have almost no effect on the determination of the operating time of the GCS in constant temperature mode. During operation of the GCS at a dimensionless coolant temperature = 0.5, the velocity of the coolant is significant. With an increase in the speed of the coolant in two times, the error changes by 1.5 times.

APPLICATION OF ADSORPTION METHOD FOR DETERMINATION OF LOCAL CONVECTIVE HEAT TRANSFER RATES

1974 ◽  
Author(s):  
S. Koncar-Djurdjevic ◽  
M. Mitrovic ◽  
S. Cvijovic ◽  
G. Popovic ◽  
Dimitrije Voronjec
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Adsorption Method ◽  
Transfer Rates

scholarly journals Experimental Determination of Stator Endwall Heat Transfer

1989 ◽  
Author(s):  
Robert J. Boyle ◽  
Louis M. Russell
Keyword(s):  
Heat Transfer ◽  
Liquid Crystal ◽  
Test Section ◽  
Electrical Power ◽  
Exhaust System ◽  
Ambient Air ◽  
Reynolds Numbers ◽  
Inlet Velocity ◽  
Turbine Vane

Local Stanton numbers were experimentally determined for the endwall surface of a turbine vane passage. A six vane linear cascade having vanes with an axial chord of 13.81 cm was used. Results were obtained for Reynolds numbers based on inlet velocity and axial chord between 73,000 and 495,000. The test section was connected to a low pressure exhaust system. Ambient air was drawn into the test section, inlet velocity was controlled up to a maximum of 59.4 m/sec. The effect of the inlet boundary layer thickness on the endwall heat transfer was determined for a range of test section flow rates. The liquid crystal measurement technique was used to measure heat transfer. Endwall heat transfer was determined by applying electrical power to a foil heater attached to the cascade endwall. The temperature at which the liquid crystal exhibited a specific color was known from a calibration test. Lines showing this specific color were isotherms, and because of uniform heat generation they were also lines of nearly constant heat transfer. Endwall static pressures were measured, along with surveys of total pressure and flow angles at the inlet and exit of the cascade.

Sign in / Sign up

Export Citation Format

Share Document