In-vitro measurement of the human knee joint motion during quadriceps leg raising

1998 ◽  
Vol 12 (4) ◽  
Author(s):  
Seonpil Kim
Keyword(s):  
Knee Joint ◽  
Joint Motion ◽  
Human Knee ◽  
Human Knee Joint ◽  
Knee Joint Motion

Accuracy of an electromagnetic measurement device and application to the measurement and description of knee joint motion

1998 ◽  
Vol 212 (5) ◽  
pp. 347-355 ◽  
Author(s):  
A M J Bull ◽  
F H Berkshire ◽  
A A Amis
Keyword(s):  
Knee Joint ◽  
Positional Error ◽  
Joint Motion ◽  
Step Size ◽  
Measurement Device ◽  
Human Knee ◽  
Multiple Receivers ◽  
Human Knee Joint ◽  
Knee Joint Motion ◽  
Electromagnetic Measurement

The aims of this study were to analyse the accuracy and sensitivity to metals of an electromagnetic motion measurement device and to use it to provide a description of motion of the human knee joint. A calibrated grid and sine bar were used to measure translational and rotational accuracy, which were found to be ±0.23 per cent of the step size (translation) and ±2.0 per cent of the step size (rotation) within an optimal operational zone of minimal positional error for which the receiver to transmitter separation was between 271 and 723 mm. The presence of multiple receivers was found to have a significant effect on the accuracy only when positioned within 30 mm of one another. Mild steel was found to have a significant detrimental effect when within 150 mm of the transmitter or receiver. A stainless steel bone screw had no effect on the accuracy of the device. A mathematical description of knee joint motion is presented which describes the motion in terms of clinical rotations. The device is a useful tool for measuring joint motion in the operating theatre and laboratory, owing to its accuracy and insensitivity to surgical alloys.

The reproducibility of passive human knee-joint motion characteristics

1985 ◽  
Vol 18 (7) ◽  
pp. 529-530
Author(s):  
L. Blankevoort ◽  
R. Huiskes ◽  
A. de Lange
Keyword(s):  
Knee Joint ◽  
Joint Motion ◽  
Human Knee ◽  
Human Knee Joint ◽  
Knee Joint Motion ◽  
Motion Characteristics

A New Load Application System for In Vitro Study of Ligamentous Injuries to the Human Knee Joint

1995 ◽  
Vol 117 (4) ◽  
pp. 373-382 ◽  
Author(s):  
J. M. Bach ◽  
M. L. Hull
Keyword(s):  
Knee Joint ◽  
Degree Of Freedom ◽  
Load Application ◽  
Accuracy Evaluation ◽  
Application System ◽  
Human Knee ◽  
Human Knee Joint ◽  
Flexion Extension ◽  
External Loads

This paper describes the design and accuracy evaluation of a new six degree of freedom load application system for in vitro testing of the human knee joint. External loads of both polarity in all six degrees of freedom can be applied either individually or in any combination while the knee is permitted to move unconstrained in response to applied loads. The flexion/extension degree of freedom permits the full physiological range of motion. In addition to external loads, forces of the three major muscle groups (quadriceps, hamstrings, gastrocnemius) crossing the joint can be developed. Full automation and rapid convergence of loads to programmed values are achieved through a computer which feeds command signals to servo controller/electro-pneumatic servo valves. The servo valves regulate pressure to pneumatic actuators which develop the various loads. Experiments undertaken to quantify the accuracy of both load and displacement measurements reveal that errors particularly in load measurement are effectively controlled through the apparatus design.

scholarly journals Modelling of the Human Knee Joint Supported by Active Orthosis

2018 ◽  
Vol 23 (1) ◽  
pp. 107-120
Author(s):  
V. Musalimov ◽  
Y. Monahov ◽  
M. Tamre ◽  
D. Rõbak ◽  
A. Sivitski ◽  
...  
Keyword(s):  
Knee Joint ◽  
Sagittal Plane ◽  
Low Cost ◽  
Lower Limbs ◽  
Human Knee ◽  
Human Knee Joint ◽  
Healthy Knee ◽  
Knee Joint Motion ◽  
Injured Knee ◽  
Active Orthosis

AbstractThe article discusses motion of a healthy knee joint in the sagittal plane and motion of an injured knee joint supported by an active orthosis. A kinematic scheme of a mechanism for the simulation of a knee joint motion is developed and motion of healthy and injured knee joints are modelled in Matlab. Angles between links, which simulate the femur and tibia are controlled by Simulink block of Model predictive control (MPC). The results of simulation have been compared with several samples of real motion of the human knee joint obtained from motion capture systems. On the basis of these analyses and also of the analysis of the forces in human lower limbs created at motion, an active smart orthosis is developed. The orthosis design was optimized to achieve an energy saving system with sufficient anatomy, necessary reliability, easy exploitation and low cost. With the orthosis it is possible to unload the knee joint, and also partially or fully compensate muscle forces required for the bending of the lower limb.

scholarly journals Direct Validation of Human Knee-Joint Contact Mechanics Derived From Subject-Specific Finite-Element Models of the Tibiofemoral and Patellofemoral Joints

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
Wei Gu ◽  
Marcus G. Pandy
Keyword(s):  
Finite Element ◽  
Knee Joint ◽  
Contact Mechanics ◽  
Contact Pressure ◽  
Weight Bearing ◽  
Human Knee ◽  
Human Knee Joint ◽  
Joint Contact ◽  
Joint Contact Pressure

Abstract The primary aim of this study was to validate predictions of human knee-joint contact mechanics (specifically, contact pressure, contact area, and contact force) derived from finite-element models of the tibiofemoral and patellofemoral joints against corresponding measurements obtained in vitro during simulated weight-bearing activity. A secondary aim was to perform sensitivity analyses of the model calculations to identify those parameters that most significantly affect model predictions of joint contact pressure, area, and force. Joint pressures in the medial and lateral compartments of the tibiofemoral and patellofemoral joints were measured in vitro during two simulated weight-bearing activities: stair descent and squatting. Model-predicted joint contact pressure distribution maps were consistent with those obtained from experiment. Normalized root-mean-square errors between the measured and calculated contact variables were on the order of 15%. Pearson correlations between the time histories of model-predicted and measured contact variables were generally above 0.8. Mean errors in the calculated center-of-pressure locations were 3.1 mm for the tibiofemoral joint and 2.1 mm for the patellofemoral joint. Model predictions of joint contact mechanics were most sensitive to changes in the material properties and geometry of the meniscus and cartilage, particularly estimates of peak contact pressure. The validated finite element modeling framework offers a useful tool for noninvasive determination of knee-joint contact mechanics during dynamic activity under physiological loading conditions.

Sign in / Sign up

Export Citation Format

Share Document