Superplastic deformation behavior of hot-rolled AZ31 magnesium alloy sheet at elevated temperatures

2006 ◽  
Vol 21 (3) ◽  
pp. 1-6 ◽  
Author(s):  
Zhang Kaifeng ◽  
Yin Deliang ◽  
Wang Guofeng ◽  
Han Wenbo
Keyword(s):  
Magnesium Alloy ◽  
Deformation Behavior ◽  
Superplastic Deformation ◽  
Elevated Temperatures ◽  
Alloy Sheet ◽  
Az31 Magnesium Alloy ◽  
Magnesium Alloy Sheet ◽  
Az31 Magnesium Alloy Sheet ◽  
Hot Rolled

Forming Behaviour at Elevated Temperature of a Laser Heat-Treated AZ31 Magnesium Alloy Sheet

2018 ◽  
Vol 941 ◽  
pp. 1270-1275
Author(s):  
Donato Sorgente ◽  
Gianfranco Palumbo ◽  
Alessandro Fortunato ◽  
Alessandro Ascari ◽  
Ali Arslan Kaya
Keyword(s):  
Magnesium Alloy ◽  
Heat Input ◽  
Elevated Temperatures ◽  
Alloy Sheet ◽  
Az31 Magnesium Alloy ◽  
Dome Height ◽  
Magnesium Alloy Sheet ◽  
Laser Heat ◽  
Az31 Magnesium Alloy Sheet ◽  
Forming Behaviour

The tailoring of mechanical and technological properties of the initial material in sheet metal forming has been widely investigated and successfully applied. The benefits of such an approach can be found in the improvement of both the post-forming performances of the manufactured component and the forming process capabilities. Different strategies can be found and most of them involve a microstructural alteration by a selective heat source (e.g. laser, induction, UV light). The use of aluminium alloys combined with these strategies has been extensively investigated, while magnesium alloys are almost not yet considered from this viewpoint. In this work, we investigated the effect of a selective laser heat treatment on an AZ31 magnesium alloy sheet. After laser heat treating a single track in the centre of a blank with different heat input values, bulge tests at elevated temperatures were conducted. The dome height evolution was continuously acquired during the tests and differences between the untreated specimen and the laser treated ones have been characterized. The effect of the laser treatment was evaluated also in terms of thickness distribution of the formed specimens. A thickness discontinuity was found along the treated specimens in the transition zone between the treated and the untreated material. Results highlighted that an effective change in the forming behaviour can be induced in the treated zone depending on the laser heat input. It has thus been shown that this approach can be employed for tailoring the magnesium alloy blank properties prior to the gas forming at elevated temperatures.

Forming Limit of AZ31 Magnesium Alloy Sheet under Non-Proportional Deformation at Elevated Temperature

2013 ◽  
Vol 535-536 ◽  
pp. 292-295 ◽  
Author(s):  
Takashi Katahira ◽  
Tetsuo Naka ◽  
Masahide Kohzu ◽  
Fusahito Yoshida
Keyword(s):  
Magnesium Alloy ◽  
Plastic Strain ◽  
Elevated Temperatures ◽  
Alloy Sheet ◽  
Az31 Magnesium Alloy ◽  
Forming Limit ◽  
Plastic Strain Increment ◽  
Magnesium Alloy Sheet ◽  
Az31 Magnesium Alloy Sheet ◽  
Strain Paths

In the present work, FLDs of AZ31 magnesium alloy sheet for non-proportional strain paths were investigated by performing two-step stretch forming experiments at various forming speeds (3, 30 and 300 mm.min-1) at elevated temperatures of 150, 200 and 250°C. The forming limit strainSuperscript texts, both for proportional and non-proportional deformations, increased with temperature rise and with decreasing forming speed. A FLC after a uniaxial pre-strain lies outside of the proportional FLC for a given condition of temperature and forming speed, whereas a biaxially pre-strained FLC lies inside of the proportional FLC. It was found that the accumulated effective plastic strain and the direction of plastic strain increment at the final stage of forming are two major factors that influence the forming limits for non-proportional deformations.

Investigation into AZ31 Sheet Metal Deep Drawing Process at Elevated Temperature

2010 ◽  
Vol 154-155 ◽  
pp. 1244-1250
Author(s):  
Peng Cheng Wang ◽  
Pei Wu ◽  
Zhi Yong Yue
Keyword(s):  
Elevated Temperature ◽  
Magnesium Alloy ◽  
Sheet Metal ◽  
Deep Drawing ◽  
Elevated Temperatures ◽  
Alloy Sheet ◽  
Az31 Magnesium Alloy ◽  
Magnesium Alloy Sheet ◽  
Az31 Magnesium Alloy Sheet ◽  
Az31 Sheet

In this paper, mechanical properties of unidirectional hot tensile tests of 3mm thick AZ31 magnesium alloy sheet metal are researched at elevated temperatures and under different tensile speeds. In this basis, thermal deep drawing of cylinders tests for 3mm thick AZ31 magnesium alloy sheet are investigated at elevated drawing temperatures, different drawing speeds and so on. Thermal deep drawing performance showed that set pieces better when elevated temperature and drawing speed range are appropriate to deep drawing.

Texture of AZ31 Magnesium Alloy Sheet Heavily Rolled by High Speed Warm Rolling

2007 ◽  
Vol 539-543 ◽  
pp. 3359-3364 ◽  
Author(s):  
Tetsuo Sakai ◽  
Hiroshi Utsunomiya ◽  
H. Koh ◽  
S. Minamiguchi
Keyword(s):  
Magnesium Alloy ◽  
High Speed ◽  
Room Temperature ◽  
Alloy Sheet ◽  
Rolling Temperature ◽  
Az31 Magnesium Alloy ◽  
Basal Texture ◽  
Double Peak ◽  
Magnesium Alloy Sheet ◽  
Az31 Magnesium Alloy Sheet

Magnesium alloy sheets had to be rolled at elevated temperature to avoid cracking. The poor workability of magnesium alloy is ascribed to its hcp crystallography and insufficient activation of independent slip systems. Present authors have succeeded in 1-pass heavy rolling of AZ31 magnesium alloy sheet below 473K by raising rolling speed above 1000m/min. Heavy reduction larger than 60% can be applied by 1-pass high speed rolling even at room temperature. The improvement of workability at lower rolling temperature is due to temperature rise by plastic working. The texture of heavily rolled AZ31 magnesium alloy sheet is investigated in the present study. The texture of sheets rolled 60% at room temperature was <0001>//ND basal texture. At the rolling temperature above 373K, the peak of (0001) pole tilted ±10-15 deg toward RD direction around TD axisto form a double peak texture. The texture varied through thickness. At the surface, the (0001) peak tilted ±10-15 deg toward TD direction around RD axis to form a TD-split double peak texture. The direction of (0001) peak splitting rotated 90 deg from the surface to the center of thickness. Heavily rolled magnesium alloy sheets have non-basal texture. The sheets having non-basal texture are expected to show better ductility than sheets with basal texture.

Sign in / Sign up

Export Citation Format

Share Document