Glucose sensors based on enzyme immobilization onto biocompatible membranes obtained by radiation-induced polymerization

1994 ◽  
Vol 49 (3) ◽  
pp. 191-202 ◽  
Author(s):  
Lucio Doretti ◽  
Daniela Ferrara ◽  
Gilberto Barison ◽  
Silvano Lora
Keyword(s):  
Enzyme Immobilization ◽  
Glucose Sensors ◽  
Radiation Induced

Patterned growth of ZnO nanorods and enzyme immobilization toward the fabrication of glucose sensors

2010 ◽  
Vol 42 (10) ◽  
pp. 2880-2883 ◽  
Author(s):  
K. Ogata ◽  
H. Dobashi ◽  
K. Koike ◽  
S. Sasa ◽  
M. Inoue ◽  
...  
Keyword(s):  
Enzyme Immobilization ◽  
Zno Nanorods ◽  
Glucose Sensors ◽  
Patterned Growth

Radiation-Induced Precipitation at Thin Foil Surfaces in Ni-Be Alloys

1982 ◽  
Vol 40 ◽  
pp. 598-599
Author(s):  
T. Mukai ◽  
T. E. Mitchell
Keyword(s):  
Electron Microscopy ◽  
High Voltage ◽  
Electron Irradiation ◽  
High Vacuum ◽  
Thin Foil ◽  
Homogeneous Precipitation ◽  
High Voltage Electron Microscopy ◽  
Voltage Electron ◽  
High Voltage Electron ◽  
Radiation Induced

Radiation-induced homogeneous precipitation in Ni-Be alloys was recently observed by high voltage electron microscopy. A coupling of interstitial flux with solute Be atoms is responsible for the precipitation. The present investigation further shows that precipitation is also induced at thin foil surfaces by electron irradiation under a high vacuum.

Annealing Of Radiation Damage in Tungsten

1970 ◽  
Vol 28 ◽  
pp. 412-413
Author(s):  
Robert C. Rau ◽  
John Moteff
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Radiation Damage ◽  
Thermal Annealing ◽  
Neutron Fluence ◽  
Dislocation Loops ◽  
Defect Clusters ◽  
Polycrystalline Tungsten ◽  
Transmission Electron ◽  
Radiation Induced

Transmission electron microscopy has been used to study the thermal annealing of radiation induced defect clusters in polycrystalline tungsten. Specimens were taken from cylindrical tensile bars which had been irradiated to a fast (E > 1 MeV) neutron fluence of 4.2 × 1019 n/cm2 at 70°C, annealed for one hour at various temperatures in argon, and tensile tested at 240°C in helium. Foils from both the unstressed button heads and the reduced areas near the fracture were examined.Figure 1 shows typical microstructures in button head foils. In the unannealed condition, Fig. 1(a), a dispersion of fine dot clusters was present. Annealing at 435°C, Fig. 1(b), produced an apparent slight decrease in cluster concentration, but annealing at 740°C, Fig. 1(C), resulted in a noticeable densification of the clusters. Finally, annealing at 900°C and 1040°C, Figs. 1(d) and (e), caused a definite decrease in cluster concentration and led to the formation of resolvable dislocation loops.

Radiation-induced surface decomposition

1983 ◽  
Vol 41 ◽  
pp. 368-369
Author(s):  
M. L. Knotek
Keyword(s):  
Ionizing Radiation ◽  
Atomic Structure ◽  
Chemical Bonding ◽  
Neutral Species ◽  
Radiation Induced ◽  
Physical And Chemical ◽  
Surface Decomposition ◽  
The Relationship ◽  
Electron And Photon ◽  
Surface Bond

Modern surface analysis is based largely upon the use of ionizing radiation to probe the electronic and atomic structure of the surfaces physical and chemical makeup. In many of these studies the ionizing radiation used as the primary probe is found to induce changes in the structure and makeup of the surface, especially when electrons are employed. A number of techniques employ the phenomenon of radiation induced desorption as a means of probing the nature of the surface bond. These include Electron- and Photon-Stimulated Desorption (ESD and PSD) which measure desorbed ionic and neutral species as they leave the surface after the surface has been excited by some incident ionizing particle. There has recently been a great deal of activity in determining the relationship between the nature of chemical bonding and its susceptibility to radiation damage.

In situ TEM studies of irradiation effects for materials improvement

1991 ◽  
Vol 49 ◽  
pp. 452-453
Author(s):  
Charles W. Allen
Keyword(s):  
Nuclear Reactor ◽  
Austenitic Stainless Steels ◽  
High Energy ◽  
Point Of View ◽  
In Situ Tem ◽  
Irradiation Effects ◽  
Tem Analysis ◽  
Radiation Induced ◽  
Analytical Tools

Irradiation effects studies employing TEMs as analytical tools have been conducted for almost as many years as materials people have done TEM, motivated largely by materials needs for nuclear reactor development. Such studies have focussed on the behavior both of nuclear fuels and of materials for other reactor components which are subjected to radiation-induced degradation. Especially in the 1950s and 60s, post-irradiation TEM analysis may have been coupled to in situ (in reactor or in pile) experiments (e.g., irradiation-induced creep experiments of austenitic stainless steels). Although necessary from a technological point of view, such experiments are difficult to instrument (measure strain dynamically, e.g.) and control (temperature, e.g.) and require months or even years to perform in a nuclear reactor or in a spallation neutron source. Consequently, methods were sought for simulation of neutroninduced radiation damage of materials, the simulations employing other forms of radiation; in the case of metals and alloys, high energy electrons and high energy ions.

Xenon ion irradiation of superconducting YBa2Cu3O7 thin films

1990 ◽  
Vol 48 (4) ◽  
pp. 92-93
Author(s):  
H. Watanabe ◽  
B. Kabius ◽  
B. Roas ◽  
K. Urban
Keyword(s):  
Defect Formation ◽  
Ion Irradiation ◽  
High Resolution Electron Microscopy ◽  
Structural Disorder ◽  
Flux Lines ◽  
Pinning Effect ◽  
Magnetic Flux Lines ◽  
Resolution Electron ◽  
Radiation Induced ◽  
Induced Defects

Recently it was reported that the critical current density(Jc) of YBa2Cu2O7, in the presence of magnetic field, is enhanced by ion irradiation. The enhancement is thought to be due to the pinning of the magnetic flux lines by radiation-induced defects or by structural disorder. The aim of the present study was to understand the fundamental mechanisms of the defect formation in association with the pinning effect in YBa2Cu3O7 by means of high-resolution electron microscopy(HRTEM).The YBa2Cu3O7 specimens were prepared by laser ablation in an insitu process. During deposition, a substrate temperature and oxygen atmosphere were kept at about 1073 K and 0.4 mbar, respectively. In this way high quality epitaxially films can be obtained with the caxis parallel to the <100 > SrTiO3 substrate normal. The specimens were irradiated at a temperature of 77 K with 173 MeV Xe ions up to a dose of 3.0 × 1016 m−2.

Applications of ultramicrotomy for materials characterization

1993 ◽  
Vol 51 ◽  
pp. 232-233
Author(s):  
R.T. Blackham ◽  
J.J. Haugh ◽  
C.W. Hughes ◽  
M.G. Burke
Keyword(s):  
Materials Science ◽  
Microstructural Analysis ◽  
Analytical Electron Microscopy ◽  
Austenitic Stainless Steels ◽  
Specimen Preparation ◽  
Preparation Technique ◽  
Thermally Induced ◽  
Radiation Induced ◽  
Characterization Of Materials

Essential to the characterization of materials using analytical electron microscopy (AEM) techniques is the specimen itself. Without suitable samples, detailed microstructural analysis is not possible. Ultramicrotomy, or diamond knife sectioning, is a well-known mechanical specimen preparation technique which has been gaining attention in the materials science area. Malis and co-workers and Glanvill have demonstrated the usefulness and applicability of this technique to the study of a wide variety of materials including Al alloys, composites, and semiconductors. Ultramicrotomed specimens have uniform thickness with relatively large electron-transparent areas which are suitable for AEM anaysis.Interface Analysis in Type 316 Austenitic Stainless Steel: STEM-EDS microanalysis of grain boundaries in austenitic stainless steels provides important information concerning the development of Cr-depleted zones which accompany M23C6 precipitation, and documentation of radiation induced segregation (RIS). Conventional methods of TEM sample preparation are suitable for the evaluation of thermally induced segregation, but neutron irradiated samples present a variety of problems in both the preparation and in the AEM analysis, in addition to the handling hazard.

Low-voltage field-emission SEM of polymeric membranes for glucose biosensors

1990 ◽  
Vol 48 (3) ◽  
pp. 860-861
Author(s):  
Lorna K. Mayo ◽  
Kenneth C. Moore ◽  
Mark A. Arnold
Keyword(s):  
Glucose Sensor ◽  
Low Voltage ◽  
Glucose Sensors ◽  
Polymeric Membranes ◽  
Artificial Endocrine Pancreas ◽  
Self Monitoring ◽  
Conducting Materials ◽  
Insulin Dependent ◽  
Living Tissues ◽  
Voltage Scanning

An implantable artificial endocrine pancreas consisting of a glucose sensor and a closed-loop insulin delivery system could potentially replace the need for glucose self-monitoring and regulation among insulin dependent diabetics. Achieving such a break through largely depends on the development of an appropriate, biocompatible membrane for the sensor. Biocompatibility is crucial since changes in the glucose sensors membrane resulting from attack by orinter action with living tissues can interfere with sensor reliability and accuracy. If such interactions can be understood, however, compensations can be made for their effects. Current polymer technology offers several possible membranes that meet the unique chemical dynamics required of a glucose sensor. Two of the most promising polymer membranes are polytetrafluoroethylene (PTFE) and silicone (Si). Low-voltage scanning electron microscopy, which is an excellent technique for characterizing a variety of polymeric and non-conducting materials, 27 was applied to the examination of experimental sensor membranes.

Sign in / Sign up

Export Citation Format

Share Document