scholarly journals Effect of heat treatment on properties of steam cured fly ash-lime compacts

2005 ◽  
Vol 28 (7) ◽  
pp. 697-702 ◽  
Author(s):  
S. Maitra ◽  
S. Das ◽  
K. Das ◽  
A. Basumajumdar
Keyword(s):  
Heat Treatment ◽  
Fly Ash

Physical, Mechanical and Micro-Structural Properties of F Type Fly-Ash Based Geopolymeric Bricks Produced by Pressure Forming Process

2010 ◽  
Vol 69 ◽  
pp. 69-74 ◽  
Author(s):  
Ömer Arıöz ◽  
Kadir Kilinç ◽  
Mustafa Tuncan ◽  
Ahmet Tuncan ◽  
Taner Kavas
Keyword(s):  
Heat Treatment ◽  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Heat Treatment Temperature ◽  
Treatment Duration ◽  
Treatment Temperature ◽  
Alumino Silicate ◽  
Heat Treatment Duration

Geopolymer is a new class of three-dimensionally networked amorphous to semi-crystalline alumino-silicate materials, and first developed by Professor Joseph Davidovits in 1978. Geopolymers can be synthesized by mixing alumino–silicate reactive materials such as kaolin, metakaolin or pozzolans in strong alkaline solutions such as NaOH and KOH and then cured at room temperature. Heat treatment applied at higher temperatures may give better results. Depending on the mixture, the optimum temperature and duration vary 40-100 °C and 2-72 hours, respectively. The properties of geopolymeric paste depend on type of source material (fly ash, metakaolin, kaolin), type of activator (sodium silicate-sodium hydroxide, sodium silicate-potassium hydroxide), amount of activator, heat treatment temperature, and heat treatment duration. In this experimental investigation, geopolymeric bricks were produced by using F-type fly ash, sodium silicate, and sodium hydroxide solution. The bricks were treated at various temperatures for different hours. The compressive strength and density of F-type fly ash based geopolymeric bricks were determined at the ages of 7, 28 and 90 days. Test results have revealed that the compressive strength values of F-type fly ash based geobricks ranged between 5 and 60 MPa. It has been found that the effect of heat treatment temperature and heat treatment duration on the density of F-type fly ash based geobricks was not significant. It should be noted that the spherical particle size increased as the heat treatment temperature increased in the microstructure of F-type fly ash based geobricks treated in oven at the temperature of 60 °C for 24 hours.

Research on Barite Concrete Mixed with Fly Ash

2013 ◽  
Vol 275-277 ◽  
pp. 2107-2111
Author(s):  
Qiu Lin Zou ◽  
Jun Li ◽  
Zhen Yu Lai
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Compressive Strength ◽  
High Temperature ◽  
Fly Ash ◽  
Apparent Density ◽  
Cycle Times ◽  
Residual Compressive Strength ◽  
Temperature Performance

Barite concrete with density grade of 3 and strength grade of C30 was prepared by mixing with different fineness of fly ash. The workability, mechanical properties and long-term high temperature performance of the prepared barite concrete were researched. Results show that the workability of barite concrete is improved by mixing with fly ash, and no segregation of mixture has been observed. The apparent density and 3d, 28d compressive strength of barite concrete are decreased obviously after mixing with fly ash. But with the increasing of the fineness of fly ash, the apparent density and 3d, 28d compressive strength of barite concrete have a slight increase. High temperature residual compressive strength is decreased with the increasing of temperature. The cycle times of heat treatment at 400°C only has a little effect on residual compressive strength of barite concrete.

scholarly journals Heat treatment effect on metal matrix composite with brass matrix and fly ash

2018 ◽  
Vol 204 ◽  
pp. 05020
Author(s):  
Aminnudin Aminnudin ◽  
Moch. Agus Choiron
Keyword(s):  
Heat Treatment ◽  
Fly Ash ◽  
Metal Matrix Composite ◽  
Matrix Composite ◽  
Coal Combustion ◽  
Metal Matrix ◽  
Treatment Process ◽  
Impact Test ◽  
Test Results ◽  
The Matrix

Metal matrix composite (MMC) is a combination of two or more materials using metal as a matrix. In this paper we used brass as the matrix and fly ash as for the particle. The fly ash used is fly ash which is produced from coal combustion in the Paiton power plant. Fly ash composition in the MMC are 5% and 10%. The MMC was produced with gas furnace. Heat tratment to MMC was done at 350 and 400 °C.Hard testing process, tensile test and impack test are carried out at MMC before heat treatment and after heat treatment. From the test results showed an increase in hardness, tensile strength and impact test showed the heat treatment process at a temperature of 350 °C. Heat treatment at a temperature of 400 °C does not improve the mechanical properties of MMC

The Fate of Lead in MSWI-Fly Ash During Heat Treatment: An X-Ray Absorption Spectroscopy Study

2009 ◽  
Vol 11 (6) ◽  
pp. 507-512 ◽  
Author(s):  
Rudolf Paul Wilhelm Jozef Struis ◽  
Maarten Nachtegaal ◽  
Harald Mattenberger ◽  
Christian Ludwig
Keyword(s):  
Heat Treatment ◽  
Fly Ash ◽  
Absorption Spectroscopy ◽  
Spectroscopy Study ◽  
Mswi Fly Ash ◽  
X Ray ◽  
X Ray Absorption

The Use of Anthracite Fly Ash for the Production of Autoclaved Aerated Concrete

2012 ◽  
Vol 512-515 ◽  
pp. 3003-3006
Author(s):  
Rostislav Drochytka ◽  
Vit Cerný ◽  
Karel Kulísek
Keyword(s):  
Heat Treatment ◽  
Fly Ash ◽  
Construction Industry ◽  
Raw Materials ◽  
Exothermic Reaction ◽  
Reaction Heat ◽  
Anthracite Coal ◽  
Concrete Production ◽  
Aerated Concrete ◽  
Cellular Concrete

Burning high-quality anthracite coal produces ash with a high content of unburned residues, which in many cases permanently exceeds 20%. These ashes usually contain high levels of amorphous phase providing the pozzolanic activity, this making them particularly useful if potentially applied in the construction industry. Such potential of effective treatment necessitates reducing the content of unburned residues, the best level here being less than 4% w/w. This paper deals with the results of testing heat treatment of fly ashes particularly using the resources of eastern Slovakia. Tests have shown that tested process of heat treatment can safely reduce the content of unburned residues in fly ash whilst maintaining high levels of the glass phase. Raw materials thus modified meet the requirements for the use in cellular concrete production technology with beneficial use of exothermic reaction heat from fly ash treatment in pre-heating the autoclaves.

Effect of Heat Treatment Process on the Preparation of Foamed Glass Ceramic from Red Mud and Fly Ash

2014 ◽  
Vol 670-671 ◽  
pp. 201-204 ◽  
Author(s):  
Yu Xi Guo ◽  
Yi He Zhang ◽  
Hong Wei Huang ◽  
Pan Hu
Keyword(s):  
Heat Treatment ◽  
Fly Ash ◽  
Glass Ceramic ◽  
Red Mud ◽  
Treatment Process ◽  
Sintering Temperature ◽  
Holding Time ◽  
Heat Treatment Process ◽  
Ceramic Foams

Lightweight glass ceramic foams have been prepared from a mixture of solid wastes, namely 40 wt-% red mud and 60 wt-% fly ash. In this work, we illustrate the effects of variables in heat treatment process, including the sintering temperature and the holding time, on the quality of the foams. The reduction of sintering temperature as well as the holding time, was found to limit the coalescence and improve the apparent density and the compressive strength.

Effect of Borax on Lightweight Material from Cullet and Fly Ash

2016 ◽  
Vol 690 ◽  
pp. 109-113 ◽  
Author(s):  
Sutthima Sriprasertsuk ◽  
Phatthiya Suwannason ◽  
Wanna T. Saengchantara
Keyword(s):  
Thermal Conductivity ◽  
Heat Treatment ◽  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Silicate ◽  
Raw Materials ◽  
Raw Material ◽  
Test Results ◽  
Heat Process ◽  
Lightweight Material

This work investigated the recycling of fly ash waste and cullet as the raw materials for lightweight bodies produced by heat treatment and using sodium silicate as the binder. Borax was mixed with fly ash and cullet, and put into the block in dimension 10x10x2 cm3. The lightweight materials thus produced were then sintered at temperature of 800 °C. Density, compressive strength and thermal conductivity were determined. Borax showed a positive sintering effect on the porosity of lightweight material during the heat process. The compressive strength of lightweight material diminished with the reduction of density and thermal conductivity. Lightweight material manufactured with borax showed the lower density and thermal conductivity accompanied by the higher compressive strength. The test results indicated that using fly ash and cullet as the raw material with borax could obtain the lightweight material, thus enhancing the possibility of its reuse in a sustainable way.

Sign in / Sign up

Export Citation Format

Share Document