Atmospheric corrosion behavior of paint systems applied on weathered hot-dip galvanized steel

2002 ◽  
Vol 74 (12) ◽  
pp. 59-68 ◽  
Author(s):  
D. Fuente ◽  
M. Morcillo ◽  
J. Simancas ◽  
L. S. Hernández ◽  
J. L. Ruiz
Keyword(s):  
Corrosion Behavior ◽  
Atmospheric Corrosion ◽  
Galvanized Steel ◽  
Paint Systems

scholarly journals Effect of Oxide Scale Microstructure on Atmospheric Corrosion Behavior of Hot Rolled Steel Strip

Coatings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 517
Author(s):  
Bin Sun ◽  
Lei Cheng ◽  
Chong-Yang Du ◽  
Jing-Ke Zhang ◽  
Yong-Quan He ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Oxide Scale ◽  
Corrosion Product ◽  
Corrosion Behavior ◽  
Corrosion Test ◽  
Atmospheric Corrosion ◽  
Corrosion Mechanism ◽  
Type I ◽  
Rust Layer ◽  
Hot Rolled

The atmospheric corrosion behavior of a hot-rolled strip with four types (I–IV) of oxide scale was investigated using the accelerated wet–dry cycle corrosion test. Corrosion resistance and porosity of oxide scale were studied by potentiometric polarization measurements. Characterization of samples after 80 cycles of the wet–dry corrosion test showed that scale comprised wüstite and magnetite had strongest corrosion resistance. Oxide scale composed of inner magnetite/iron (>70%) and an outer magnetite layer had the weakest corrosion resistance. The corrosion kinetics (weight gain) of each type of oxide scale followed an initial linear and then parabolic (at middle to late corrosion) relationship. This could be predicted by a simple kinetic model which showed good agreement with the experimental results. Analysis of the potentiometric polarization curves, obtained from oxide coated steel electrodes, revealed that the type I oxide scale had the highest porosity, and the corrosion mechanism resulted from the joint effects of electrochemical behavior and the porosity of the oxide scale. In the initial stage of corrosion, the corrosion product nucleated and an outer rust layer formed. As the thickness of outer rust layer increased, the corrosion product developed on the scale defects. An inner rust layer then formed in the localized pits as crack growth of the scale. This attacked the scale and expanded into the substrate during the later stage of corrosion. At this stage, the protective effect of the oxide scale was lost.

Evaluation Method for Time-Dependent Corrosion Behavior of Carbon Steel Plate Using Atmospheric Corrosion Monitoring Sensor

2009 ◽  
Vol 417-418 ◽  
pp. 417-420 ◽  
Author(s):  
Shigenobu Kainuma ◽  
Kunihiro Sugitani ◽  
Yoshihiro Ito ◽  
In Tae Kim
Keyword(s):  
Carbon Steel ◽  
Corrosion Behavior ◽  
Atmospheric Corrosion ◽  
Evaluation Method ◽  
Steel Plates ◽  
Time Dependent ◽  
Corrosion Monitoring ◽  
Corrosion Sensor ◽  
Atmospheric Exposure ◽  
Corrosive Environments

The purpose of this research is to propose a method for evaluating the time-dependent corrosion behavior of carbon steel plates using an atmospheric corrosion monitor (ACM) corrosion sensor consisting of a Fe/Ag-galvanic couple. Atmospheric exposure tests were carried out on steel　plates for periods of 6, 12, and 24-months on the island of Okinawa in Japan. The Specimens were mounted on racks at angles of 0, 45 and 90 to the horizontal to obtain corrosion data in various corrosive environments. In addition, the environments of the skyward- and groundward-facing surfaces of the specimens were monitored using ACM sensors. The sensor outputs were recorded during the exposure tests.

The Effect of Composition and Microstructure on Corrosion Behavior in SST of Zn-Al-Mg Galvanized Steel Sheet

2013 ◽  
Vol 442 ◽  
pp. 64-69
Author(s):  
Feng Li ◽  
Jia Shun Lv ◽  
Hong Gang Yang ◽  
Fang Zhou ◽  
Leng Zhang ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Steel Sheet ◽  
Alloy Composition ◽  
Element Distribution ◽  
Galvanized Steel ◽  
Good Corrosion Resistance ◽  
Excellent Corrosion Resistance

Z11A3M, Z6A3M, Z1.6A1.6M, Z1A1M and Z1M coating samples were prepared in HDPS by traditional continuous hot dipping method. The microstructure, element distribution and phase was analyzed by SEM, EPMA and XRD. The corrosion resistance was checked in SST. The result was, MgZn2 and eutectic could be found in all ZAM coating. The ZAM coatings showed excellent corrosion resistance in SST than GI. The corrosion resistance was 4.1 to 11 times of GI. There was no strong relativity between alloy composition and corrosion resistance due to Mg enrichment on the surface of coating. Edge-unsealed ZAM samples showed good corrosion resistance than edge-sealed sample.

Sign in / Sign up

Export Citation Format

Share Document