Some characteristics of a spin combustion site and of the processes occurring in it

1998 ◽  
Vol 34 (3) ◽  
pp. 288-291 ◽  
Author(s):  
A. K. Filonenko
1981 ◽  
Vol 42 ◽  
pp. 1-6 ◽  
Author(s):  
A.P. Aldushin ◽  
B.A. Malomed ◽  
Ya.B. Zeldovich

2000 ◽  
Vol 28 (1) ◽  
pp. 1421-1429 ◽  
Author(s):  
Igor Filimonov ◽  
Nickolai Kidin ◽  
Alexander Mukasyan

Author(s):  
V. S. Babkin ◽  
I. Wierzba ◽  
G. A. Karim

Combustion processes with excess enthalpy are described with examples given. It is shown that different processes, such as heat and mass transfer, phase and chemical changes are involved. Moreover, flames with excess enthalpy can be encountered in a variety of forms such as laminar or turbulent, within homogeneous or heterogeneous systems involving stationary or unsteady processes, with pulse or spin combustion and as cellular flames. It is to be shown that mainly due to the increase in the chemical reaction rates within the combustion zone, the excess enthalpy state can lead to substantial increases in the burning rates, widening the associated flammability limits and modifying the preignition processes. Some applications that can benefit from the use of such flames are outlined.


1982 ◽  
Vol 18 (2) ◽  
pp. 134-139 ◽  
Author(s):  
A. V. Dvoryankin ◽  
A. G. Strunina ◽  
A. G. Merzhanov
Keyword(s):  

2008 ◽  
Vol 78 (1) ◽  
pp. 612-616 ◽  
Author(s):  
A. M. Samoilenko ◽  
E. P. Belan

1990 ◽  
Vol 1 (1) ◽  
pp. 73-89 ◽  
Author(s):  
Marc Garbey ◽  
Hans G. Kaper ◽  
Gary K. Leaf ◽  
Bernard J. Matkowsky

This article is concerned with the structure and stability properties of a combustion front that propagates in the axial direction along the surface of a cylindrical solid fuel element. The fuel consists of a mixture of two finely ground metallic powders, which combine upon ignition in a one-step chemical reaction. The reaction is accompanied by a melting process, which in turn enhances the reaction rate. The combustion products are in the solid state. The reaction zone, inside which the melting occurs, is modelled as a front that propagates along the surface of the cylinder. The different modes of propagation that have been observed experimentally (such as single- and multiheaded spin combustion and multiple-point combustion) are explained as the results of bifurcations from a uniformly propagating plane circular front. The stability properties of the various modes are discussed.


Author(s):  
I. A. Koznacheev ◽  
K. V. Dobrego

The one-dimensional axisymmetric problem of initiation of a combustion wave in an oil-saturated reservoir is solved numerically. Two combustible components, viz. liquid (oil) and solid (kerogen, oil sorbate) were considered. The influence of the abovementioned components on time of the hot site ignition and combustion front speed was simulated and analyzed. It was demonstrated that growth of the mass fraction of liquid component (the total heat content being preserved) results in retard of formation of the hot site near the well and in reduction of the maximum temperature of the combustion wave, disregarding of the higher reactivity of liquid combustible. Simulation revealed existence of the two “peaks” of thermal front velocity. The first one corresponds by time to ignition of combustion site. The second one corresponds to a moment when the solid component combustion front overrides the oil displacement front. Calculations shown, that thermal wave propagation velocity, at least after passing the “peaks” and transition to quasi-steady regime, does not considerably depend on mass traction of the fluid component in the system. A typical term of the exothermic reaction site formation may increase from 50 to 200 days in case of growth of the liquid component content from 30 to 80 mass % at the considered thermal conditions in the oil reservoir. Thus, the implementation of the thermo-gas method in high-productive layers increases the likelihood of difficulty of initiation of a fire. Therefore, the study of the regularities of intra-combustion in such cases is of a particular interest. For instance, the task of combustion site ignition may be resolved by increase of oxygen content in blowing-gas or by means of non-steady (periodical) blowing. It is found that taking into consideration of highly reactive liquid component results in widening (diffusion) of the thermal front, which may play positive role in its spatial thermo-hydrodynamic stabilization. The results of simulation may be utilized for development of technical projects of oil recovery via in-situ combustion, for designing of furnaces utilizing multicomponent fixed layer fuels and for thermochemical investigation of multicomponent fuels.


2015 ◽  
Vol 51 (2) ◽  
pp. 214-231
Author(s):  
A. M. Samoilenko ◽  
E. P. Belan
Keyword(s):  

Sign in / Sign up

Export Citation Format

Share Document